co2-naooch-h2o- you ji an duo xiang fu he ping heng xi tong de re li xue mo xing

Hu Liang,Luo Zanchun,Su Yuanfu

1991-01-01

Abstract:测定了25℃时HCOOH-H 2 O-有机胺和CO 2 -NaOOCH-H 2 O-有机胺系统的平衡数据。通过对复合平衡过程的分解和简化,利用Pitzer方程和NRTL方程,建立了CO 2 -NaOOCH-H 2 O-有机胺复合平衡系统的热力学模型。模型计算值与实验值的吻合情况良好。

What problem does this paper attempt to address?

Measurement And Modeling Of The High-Pressure Phase Behavior Of The Carbon Dioxide Plus Propene Oxide Binary System

Jia-Jun Wang,Jin-Tang Duan,Long Wang,Xue-Ping Gu,Lian-Fang Feng

DOI: https://doi.org/10.1021/je100142g

2010-01-01

Abstract:The phase equilibrium of the binary system carbon dioxide + propene oxide has been determined for carbon dioxide mole fractions from 0.1 to 0.7 and temperatures from (303.2 to 353.2) K. The experimental measurements of bubble points were carried out in an experimental device incorporating a moveable piston and a vision window. A good description of the phase behavior in a wide range of temperatures with the Peng-Robinson equation of state using the one-parameter conventional van der Waals mixing rule has been obtained, on the basis of measured data and literature data for the carbon dioxide + propene oxide system. The binary interaction parameter k(ij) has been optimized to match experimental data at each temperature separately and found to be temperature-dependent, especially at high temperatures.
Calculation Model of Henry′s Constants of Oxygen in Aqueous Acetic Acid

Xi Li

2007-01-01

Abstract:Proper calculation model for Henry's constants of oxygen in aqueous acetic acid at high temperature is not available at present.Hu′s extended scaled particle theory(1985) is applicable for various systems under extensive temperature range,but no report on applying this theory to organic acid system is available for the moment.Based on the extended scaled particle theory,this model was modified in two aspects to build a Henry's constant calculation model for oxygen in aqueous acetic acid: one was about considering the dependence of thermodynamic parameters on temperature;the other was about adjusting the effective size parameter of oxygen according to the feature of organic solution.The parameters of this model were regressed from the literature data,and the Henry's constants of oxygen in aqueous acetic acid from the published experimental data were consistent with the Henry's constants estimated by the developed calculation model.The method can be used to predict the Henry's constants of oxygen in aqueous acetic acid at different temperatures(273-500 K) and in different acetic acid mass concentration(0-100%).
THERMODYNAMIC CONSISTENCY FOR THE VAPOR-LIQUID EQUILIBRIUM DATA OF ASSOCIATING SYSTEM

彭勇,梁菊,平丽娟,毛建卫,朱虹

2009-01-01

Abstract:Based on the chemical theory and the Hayden-O'Connell(HOC) method,the association system's real vapor phase composition and the phase equilibrium computation general formula were inferred completely,and simplified at atmospheric and reduced pressure.The associating system thermodynamic consistency check method had established.Isobaric vapor-liquid equilibrium(VLE) data of the water+formic acid,water+acetic acid and water+propionic acid systems were correlated.The predicted value obtained in this way agreed well with the literature value.The results showed that the model was simple and reliable,and very few basic properties constants were required.Finally,the experimental VLE data of acetic acid+N,N-dimethylformamide the system were taken as the example,its thermodynamic consistency was checked by the establishment association system thermodynamics consistency check method,the Herington area test and the point-to-point method.
CO2 Removal from Air by Hollow-fiber Membrane-based Absorption System

叶向群,孙亮,张林,周志军,陈欢林

DOI: https://doi.org/10.3321/j.issn:1003-9015.2003.03.001

2003-01-01

Abstract:In order to remove CO2 from air,alkanolamines were chosen as the absorbent,and a CO2 removal system was built with two polypropylene hollow-fiber membrane modules.The results showed that,when concentration of absorbent Cam is 2.0mo1·L-1,air fow raate Vg is less than 0.30 m·s-1,and absorbent flow rate V1 is less than 0.01 m·s-1,the overall mass transfer coefficent Ka of CO2 aborption is about 0.03~0.06mol·m-2·min-1·(mol·L-1)-1.The effect of V1 and Vg on mass transfer coefficient Ka was investigated.Mass transfer in gas phase is the controlling step.A mathematical model of Ka was set up.The results from the model are in good agreement with the experimental data.The model could be used for process design of membrane-based absorption.
CO2 Solubility Measurement and Thermodynamic Modeling for 1-Methylpiperazine/water/co2

Han Li,Yann Le Moullec,Jiahui Lu,Jian Chen,Jose Carlos Valle Marcos,Guofei Chen,Fabrice Chopin

DOI: https://doi.org/10.1016/j.fluid.2015.03.021

IF: 2.745

2015-01-01

Fluid Phase Equilibria

Abstract:An accurate thermodynamic model is the primary element needed for the process simulation and optimization for CO2 absorption in aqueous amine solutions. In this work, the thermodynamic model was built in Aspen Plus, using the electrolyte nonrandom two-liquid (ENRTL) activity coefficient model to represent vapor pressure and heat capacity data, simultaneously, for amine, vapor–liquid equilibrium (VLE), excess enthalpy (HE), and pKa data for amine/H2O, and CO2 solubility data for amine/CO2/H2O. The cyclic diamine 1-methylpiperazine (1MPZ) is a promising amine for CO2 capture. CO2 solubility was measured for 1MPZ aqueous solutions at three concentrations – 10wt%, 30wt%, and 40wt% and four temperatures – 313.15K, 343.15K, 373.15K, and 393.15K. The excess enthalpy for 1MPZ+H2O was obtained by the Setaram C80 calorimeter at 303.15K and 323.15K, within a whole mole-fraction range. The interaction parameters of nonrandom two-liquid model (NRTL) and ENRTL, along with the standard state properties of amine ions – protonated 1MPZ (1MPZH+, 1MPZH2+), 1MPZ carbamate (1MPZCOO−), and protonated 1MPZ carbamate (H1MPZCOO) – were regressed from data obtained from this work as well as literature, which agreed with the model calculation.
Experimental and Thermodynamic Study on New CO2 Absorbents

Mengyue Zhou,Yubing Liu,Hongwei Li,Zhigang Tang,Xiao Xing,Dong Guo,Weiyang Fei

DOI: https://doi.org/10.1016/j.ccst.2022.100040

2022-01-01

Carbon Capture Science & Technology

Abstract:UNIFAC model is a thermodynamic model for predicting activity coefficients based on the group contribution method, which is very important in predicting gas-liquid equilibrium, especially for CO2-absorbent system. In this research, we used UNIFAC model to regress the interaction parameters of -CH2O versus CO2, -CH2O versus -CO3 in CO2 -1, 2-Dimethoxyethane and Dimethyl Carbonate-1, 2-Dimethoxyethane system through experimental and literature data, and predicted the increased solubility of CO2 in the absorbents with increased number of ether bonds and carbon chain. Results revealed the Henry's coefficient of CO2 in CO2- Dimethyl Carbonate system is 1.32 and 1.42 times higher than that in CO2-pentane-3-oxy-1,5-diyl dimethyl dicarbonate and CO2- octane-3,6dioxy-1,8-diyl dimethyl dicarbonate system at 323.15K, respectively. The gas-liquid equilibrium results calculated by UNIFAC model correspond well with experimental results. This study provides a new idea for designing CO2 new absorbent.
Vapor-liquid Equilibrium Measurement and Heating Performance Modeling on Eco-Friendly Zeotropic Blends of CO2/R1234ze(Z) and CO2/R1336mzz(E)

Jielin Luo,Zhiming Ye,Zhen Zhao,Kaiyin Yang,Shaozhi Zhang,Qin Wang

DOI: https://doi.org/10.1016/j.applthermaleng.2023.120576

IF: 6.4

2023-01-01

Applied Thermal Engineering

Abstract:In the context of sustainable development, CO2 and hydrofluoroolefins (HFOs) are regarded as promising refrigerant candidates. Despite recognition of application potential, the knowledge of their blends is insufficient. In this paper, vapor-liquid equilibrium (VLE) properties of two eco-friendly zeotropic CO2/HFO blends, namely CO2/R1234ze(Z) and CO2/R1336mzz(E), were measured at temperature from 253.15 K to 333.15 K at CO2 concentration from 0 to 1. Peng-Robinson (PR) model and Soave-Redlich-Kwong (SRK) model are identified as suitable models for describing VLE of CO2/HFO with deviation less than 4.5%, whereas Perturbed-Chain Sta-tistical Associating Fluid Theory (PC-SAFT) model is shown to have larger deviation. Furthermore, a heat pump water heater is modelled to demonstrate the working potential of CO2/HFO in terms of thermodynamics and safety, while the newly fitted binary interaction parameter kij being used. Both CO2/R1234ze(Z) and CO2/ R1336mzz(E) show more than 150% advantage in volumetric heating capacity and comparable heating effi-ciency compared to R134a. The optimal concentration of CO2 is higher than 0.6, eliminating the flammability of mixture. Additionally, the operating pressures of CO2/HFO are reduced to lower than 3.2 MPa at typical working condition due to HFO addition. The results contribute to the accurate VLE description of CO2/HFO and further investigation on the applications of eco-friendly refrigerants.
A vapor-liquid phase equilibrium model for binary CO2-H2O and CH4-H2O systems above 523 K for application to fluid inclusions

ShiDe Mao,Zhenhao Duan,Wenxuan Hu

DOI: https://doi.org/10.1016/j.supflu.2009.02.007

IF: 3.9

2009-01-01

The Journal of Supercritical Fluids

Abstract:Accurate prediction of both volumetric and vapor–liquid phase equilibria of binary CO2–H2O and CH4–H2O mixtures with a single equation of state proves to be difficult. In this study we use an activity–fugacity model to predict the vapor–liquid phase equilibria above 523K and adapt a Helmoholtz model to calculate volumetric properties of these two binary systems. The average deviations of water content in the vapor phase from experimental data are 3.25% and 3.19% for the CO2–H2O and CH4–H2O mixtures, respectively, and the average deviations of gas solubility in liquid phase from experimental data are 4.29% and 3.50%, respectively. The model can find wide applications, and an example is given for the analysis of fluid inclusions in geochemistry.
Composition Analysis of Co2-Nh3-H2o System Based on Raman Spectra

Qing Zhao,Shujuan Wang,Feng Qin,Changhe Chen

DOI: https://doi.org/10.1021/ie1010178

2011-01-01

Industrial & Engineering Chemistry Research

Abstract:We used Raman spectroscopy to systematically and comprehensively measure the concentrations of the main ion components (NH2COO-, HCO3-, and CO32-) in the CO2-NH3-H2O system for an initial total ammonia concentration [A] = 0.69, 0.88, 1.09, 1.34, 1.60, and 2.10 mol.L-1 and CO2 loading [C]/[A] = 0.18, 0.35, 0.43, 0.50, and 0.67, respectively. The experimental data were processed using two existing theoretical methods, and the analysis on results allowed us to propose a number of improvements based on these theoretical methods. Experimental results show that upon increasing [C]/ [A], the ratios of [NH2COO-] and [CO32-] to total carbon decrease linearly, whereas the ratio of [HCO3-] to total carbon increases linearly. The reaction process can be divided into three steps. Considering the impacts of experiment errors, [A] has little effect on the relative composition of the system in the range we studied. Results calculated with a revised theoretical method are in better agreement with the experimental data.
Experimental and an Electrolyte Non-Random Two-Liquid Model to Predict the Vapor–liquid Equilibrium of CO2 in Aqueous Solutions of Diethylenetriamine

Ruilei Zhang,Yandong Tang,Weifeng Shan,Haijun Liu,Haijun Li,Jian Chen

DOI: https://doi.org/10.1177/1747519820964179

2020-01-01

Journal of Chemical Research

Abstract:The absorption and desorption data of CO2 in aqueous solutions with a mass fraction of 10% and 20% of diethylenetriamine are measured at 313.15, 343.15, 373.15, and 393.15 K. The electrolyte non-random two-liquid theory is developed using Aspen V9.0 to correlate and predict the vapor–liquid equilibrium of CO2 in aqueous diethylenetriamine solutions. The model predicted the heat capacity and saturated vapor pressure data of diethylenetriamine, the mixed heat of a diethylenetriamine–H2O binary system, and the vapor–liquid equilibrium data of a diethylenetriamine–H2O–CO2 ternary system. The physical parameters and the interaction parameters of the model system are calculated. The model predicted CO2 solubility showing a 10% average absolute deviation from experimental data. The calculated values of the model are basically consistent with the experimental values.
Measurement and Thermodynamic Modeling for CO2 Solubility in the N-(2-Hydroxyethyl) Piperazine + Water System

Simeng Li,Gern Woo Kang,Jian Chen

DOI: https://doi.org/10.3389/fenrg.2021.785039

IF: 3.4

2021-01-01

Frontiers in Energy Research

Abstract:Amine scrubbing is the most important technique for capturing CO2. The cyclic diamine N-(2-Hydroxyethyl)-piperazine (HEPZ), a derivative of piperazine, with good mutual solubility in aqueous solution, a low melting point, and a high boiling point, has the potential to replace PZ as an activator added in the mixed amine system to capture CO2. In this study, the solubility of CO2 in aqueous HEPZ solutions was determined for three HEPZ concentrations and four temperatures. The VLE data for HEPZ-H2O were obtained using a gas–liquid double circulation kettle at pressure 30–100 kPa, and the thermodynamic model for the HEPZ-H2O-CO2 system was built in Aspen Plus based on the electrolytic non-random two-liquid (ENRTL) activity model. The physical parameters for HEPZ and the interaction parameters for ENRTL, along with reaction constants of carbamate reactions, were regressed. Using the thermodynamic model, the CO2 cyclic capacity, speciation with loading, and heat of reaction for the CO2 capture system by the aqueous HEPZ solution are predicted and analyzed.
Simulations of vapor–liquid phase equilibrium and interfacial tension in the CO2–H2O–NaCl system

yang liu,thomas lafitte,athanassios z panagiotopoulos,pablo g debenedetti

DOI: https://doi.org/10.1002/aic.14042

IF: 4.167

2013-01-01

AIChE Journal

Abstract:Direct interfacial molecular dynamics simulations are used to obtain the phase behavior and interfacial tension of CO2-H2O-NaCl mixtures over a broad temperature and pressure range (50 degrees CT250 degrees C, 0P600 bar) and NaCl concentrations (1-4 mol/kg H2O). The predictive ability of several existing water (SPC and TIP4P2005), carbon dioxide (EPM2 and TraPPE), and sodium chloride (SD and DRVH) models is studied and compared, using conventional Lorentz-Berthelot combining rules for the unlike-pair parameters. Under conditions of moderate NaCl molality (approximate to 1 mol/kg H2O), the predictions of the CO2 solubility in the water-rich and CO2-rich phase resemble those in the CO2-H2O system [Liu et al., J Phys Chem B. 2011;115:6629-6635]. Consistent with our previous work, the TraPPE/TIP4P2005 model combination gives the best overall performance in predicting coexistence composition and pressure in the water-rich phase. Critical assessments are also made on the ranges of temperature and pressure where particular model combinations work better. The dependence of the interfacial tension on temperature and pressure is better predicted by the TraPPE/TIP4P2005 and EPM2/SPC models, whereas the EPM2/TIP4P2005 model overestimates this property by 10-20%, possibly due to the inadequacy of the combining rules. It is also found that the interfacial tension increases with salt concentration, consistent with experimental observations. (c) 2013 American Institute of Chemical Engineers AIChE J, 59: 3514-3522, 2013
Phase Equilibrium Calculation of Mixtures: Comparison of SAFT, Modified SAFT, and BACK EOS for Supercritical CO2-C2H5OH System

张志禹,胡中桥,杨基础,李以圭

2002-01-01

Abstract:Three calculational models, statistical associating fluid theory (SAFT), modified SAFT, and Boublík-Alder-Chen-Kreglewshi (BACK) are compared for supercritical CO2-C2H5OH using a set of van der Waals type mixing rules for both the BACK equation of state (EOS) and the SAFT EOS. Equations are presented for the residual Helmholtz free energy, residual chemical potentials, and compressibilty factor for mixtures. A comparison with experimental vapor-liquid equilibrium (VLE) data reveals that the BACK EOS together with the suggested mixing rules provides more accurate prediction of the binary system than the SAFT or the modified SAFT model with no adjustable binary parameters. The correlation results are improved with an adjustable parameter.
Thermodynamic Model and Process Simulation for CO2 Removal with Low Temperature Methanol

XIAO Zhen-ping,FANG Ding-ye,YING Wei-yong,LIU Sen,CHEN Jian

DOI: https://doi.org/10.3969/j.issn.1005-9954.2011.07.018

2011-01-01

Abstract:For the study on simulation of CO2 capture processes with low temperature methanol,a thermodynamic model was established for a system with gases and strong polar components under high pressure.The Soave-Redlich-Kwong(SRK) cubic equation of state,Huron-Vidal mixing rule and Non-Random-Two-Liquid(NRTL) model for activity coefficients were used,and 45 pairs of parameters activity coefficient model were regressed with gas solubility and vapor-liquid equilibrium data.The simulation of the CO2 removal process was carried out.The results show that the thermodynamic method is valid for the process simulation with nonpolar gases such as H2,N2,CH4 and strong polar components such as CH3OH and H2O.
Thermodynamic studies for improving the prediction of CO2 equilibrium solubility in aqueous 2-dimethylamino-2-methyl-1-propanol

Rui Zhang,Xinwei He,Tianzi Liu,Min Xiao,Hao Ling,Xiayi Hu,Xiaowen Zhang,Feiying Tang,Chao''en Li,He''an Luo

DOI: https://doi.org/10.1016/j.seppur.2022.121292

IF: 8.6

2022-08-15

Separation and Purification Technology

Abstract:In this work, CO2 equilibrium solubility in aqueous 2-(dimethylamino)-2-methyl-1-propanol (2DMA2M1P) solution was investigated by varying temperature, CO2 partial pressure and amine concentration. Dissociation constant (pKa) and CO2 absorption heat of 2DMA2M1P were calculated. Results show that the CO2 equilibrium solubility increases with the CO2 partial pressure but decreases with the increase of temperature. It was also revealed that the CO2 equilibrium solubility declines when the concentration of 2DMA2M1P increases from 1 to 2 mol/L. In addition, a new extended Cf model was proposed for predicting the CO2 equilibrium solubility, and the predicted results show a good agreement with the experimental measured data with an average absolute deviation (AAD) of 2.08%. Furthermore, the proposed model was validated with the published data of tertiary amines, and the results indicate that the developed model has a good universality in predicting the CO2 equilibrium solubility. Finally, a comparison with other reported amines was also made in terms of the CO2 equilibrium solubility and the CO2 absorption heat. All of them proved that the 2DMA2M1P could be a competitive amine solvents for CO2 capture.

engineering, chemical
Experiment and Modeling of Vapor–liquid Equilibria for H2O+CH3OH+KCl and H2O+CH3OH+NaBr Systems

Xianzhen Xu,Yu Zhou,Zonghua Wang,Xi Wang

DOI: https://doi.org/10.1016/j.calphad.2018.09.003

2018-01-01

Abstract:In this work, vapor–liquid equilibrium (VLE) data were reported on mixed solvent electrolyte systems containing H2O+CH3OH+KCl and H2O+CH3OH+NaBr. The measurements were carried out in a computer-controlled glass apparatus. A new model based on UNIQUAC equation was proposed for the correlation of vapor–liquid equilibria in mixed solvent electrolyte systems. The model for the excess Gibbs energy was modified from the UNIQUAC equation, and the activity coefficients were calculated by UNIQUAC terms and solvent-solution effect terms. In addition, an assumption for the solution effect was introduced into this model. Experiment and literature data for mixed solvent electrolyte systems were successfully correlated using the proposed model.
Thermodynamic Calculations of the Critical Points of the H2–CO2–CH4–CO–H2O System

Cheng Siyuan,Ma Weigang,Sakoda Naoya,Zhang Xing

DOI: https://doi.org/10.1007/s10765-020-02725-5

2020-01-01

International Journal of Thermophysics

Abstract:Knowledge of the stability limit and critical point of the H 2 –CO 2 –CH 4 –CO–H 2 O system is significant for the management and optimization of the gasification systems of organic substances in supercritical water. We report thermodynamic calculations of the stability limits and critical points of the H 2 –CO 2 –CH 4 –CO–H 2 O system based on the cubic equation of state. Prior to the calculations of the quinary system, phase equilibria of the H 2 –CO 2 and CH 4 –C 2 H 6 systems and critical points of the CO 2 –H 2 O system were calculated and compared with experimental data. The calculated temperature stability limit decreased as the mole fraction of H 2 in the quinary system increased. The calculated critical point of the (0.50 H 2 + 0.01 CO 2 + 0.02 CH 4 + 0.02 CO + 0.45 H 2 O) mixture (in mole fractions) was at about 610 K and 300 MPa. The increase in the mole fraction of CO 2 or H 2 O and the corresponding decrease of the mole fraction of H 2 in the quinary system would make the critical temperature and pressure change significantly. The calculations indicated that all the p – T states of the quinary system in our previous work were stable.
Density Measurement and PC-SAFT/tPC-PSAFT Modeling of the CO2 + H2O System over a Wide Temperature Range

Yongchen Song,Weiwei Jian,Yi Zhang,Mingjun Yang,Jiafei Zhao,Weiguo Liu,Yu Liu,Yong Shen

DOI: https://doi.org/10.1021/je500062a

IF: 3.119

2014-01-01

Journal of Chemical & Engineering Data

Abstract:The aim of this work is to report the (p, p, T) densities for the CO2 + H2O system from 274.15 K to 413.15 K and for pressures up to 18 MPa. The binary mixtures were initially synthesized at compositions with a CO2 mole fraction of x(1) = (0, 0.0042, 0.0084, and 0.0124). The experimental densities were measured using a magnetic suspension balance with a high-pressure measurement cell. The densities of the CO2 + H2O solutions increased linearly with increasing pressure and decreased with increasing temperature. The partial molar volumes calculated from the experimental densities had a good agreement with the model proposed by Sedlbauer et al. The perturbed chain-statistical associating fluid theory (PC-SAFT) and the truncated PC-polar SAFT (tPC-PSAFT) equations of state were used to calculate the densities of the CO2 + H2O systems in four different cases. Different models of the CO2 and the H2O components were presented in this work. In PC-SAFT, CO2 was modeled as a nonassociation molecule, and H2O was modeled as a molecule with four associating sites. For tPC-PSAFT, CO2 was considered as a nonassociation molecule with a quadrupole moment, and H2O was a molecule with four association sites and a dipole moment. In both PC-SAFT and tPC-PSAFT, correlations were established for the association parameters of pure water and the binary interaction parameter k(12), which markedly improved the accuracy of the prediction. The improved PC-SAFT, combined with the correlated association parameters of the pure water and k(12), gave the best prediction for the experimental densities in this work and in previous studies. The density differences between the pure water and the CO2 + H2O solutions were also predicted well by the improved PC-SAFT.
The CPA Equation of State and an Activity Coefficient Model for Accurate Molar Enthalpy Calculations of Mixtures with Carbon Dioxide and Water/Brine

P. C. Myint,Y. Hao,A. Firoozabadi

DOI: https://doi.org/10.48550/arXiv.1504.05123

2015-04-20

Soft Condensed Matter

Abstract:Thermodynamic property calculations of mixtures containing carbon dioxide (CO$_2$) and water, including brines, are essential in theoretical models of many natural and industrial processes. The properties of greatest practical interest are density, solubility, and enthalpy. Many models for density and solubility calculations have been presented in the literature, but there exists only one study, by Spycher and Pruess, that has compared theoretical molar enthalpy predictions with experimental data. In this report, we recommend two different models for enthalpy calculations: the CPA equation of state by Li and Firoozabadi, and the CO$_2$ activity coefficient model by Duan and Sun. We show that the CPA equation of state, which has been demonstrated to provide good agreement with density and solubility data, also accurately calculates molar enthalpies of pure CO$_2$, pure water, and both CO$_2$-rich and aqueous (H$_2$O-rich) mixtures of the two species. It is applicable to a wider range of conditions than the Spycher and Pruess model. In aqueous sodium chloride (NaCl) mixtures, we show that Duan and Sun's model yields accurate results for the partial molar enthalpy of CO$_2$. It can be combined with another model for the brine enthalpy to calculate the molar enthalpy of H$_2$O-CO$_2$-NaCl mixtures. We conclude by explaining how the CPA equation of state may be modified to further improve agreement with experiments. This generalized CPA is the basis of our future work on this topic.
Predicting Vapor-Liquid Equilibria of CO2+HFC Binary Mixtures by the PR EOS Combined with a Group Contribution Model

Zirui Wu,Lingfeng Shi,Rui Sun,Hua Tian,Xuan Wang,Gequn Shu

DOI: https://doi.org/10.52396/justc-2023-0001

2023-01-01

JUSTC

Abstract:CO2+HFC binary mixtures have good performance and environmental friendliness and are considered good alternative working fluids in cooling and power cycle systems. The vapor-liquid phase equilibrium properties are key to the calculation of the enthalpy and entropy of mixtures, which is critical for the analysis of cooling and power cycle systems. To accurately predict the vapor-liquid equilibrium of CO2 and HFC (R23, R32, R41, R125, R134a, R143a, R152a, R161, and R227ea) binary mixtures, a group contribution model based on the excess free energy (GE) mixing rules (PR+MHV1+UNIFAC and PR+LCVM+UNIFAC) is established in this paper. The interaction parameters between groups such as -CO2, -Alkane, -CHF, and -CHF3 are obtained by the vapor-liquid phase equilibrium experiment of CO2 and HFC refrigerants, and these group parameters are critical for predicting their vapor-liquid phase equilibrium properties (the pressures and vapor phase molar fractions). The AARDp value calculated by the PR+LCVM+UNIFAC model is 5.53%, the value of AADy1 is 0.0132, and the AARDp and AADy1 values of the PR+MHV1+UNIFAC model are 7.40% and 0.0229, respectively. However, for the CO2+R32 system, the PR+MHV+UNIFAC prediction model can reproduce the experimental data with lower deviations, and the values of AARDp and AADy1 are 1.53% and 0.0045, respectively. In summary, for CO2+HFC binary mixtures, the PR+LCVM+UNIFAC group contribution model can reproduce the experimental data with lower deviations, but for individual CO2 binary mixtures (such as CO2+R32), the PR+MHV1+UNIFAC model also has unique advantages. According to the prediction results of the group contribution model, the PR+LCVM+UNIFAC model has significantly improved the calculation progress compared with the PR+MHV1+UNIFAC model used in the previous system.

co2-naooch-h2o- you ji an duo xiang fu he ping heng xi tong de re li xue mo xing

Measurement And Modeling Of The High-Pressure Phase Behavior Of The Carbon Dioxide Plus Propene Oxide Binary System

Calculation Model of Henry′s Constants of Oxygen in Aqueous Acetic Acid

THERMODYNAMIC CONSISTENCY FOR THE VAPOR-LIQUID EQUILIBRIUM DATA OF ASSOCIATING SYSTEM

CO2 Removal from Air by Hollow-fiber Membrane-based Absorption System

CO2 Solubility Measurement and Thermodynamic Modeling for 1-Methylpiperazine/water/co2

Experimental and Thermodynamic Study on New CO2 Absorbents

Vapor-liquid Equilibrium Measurement and Heating Performance Modeling on Eco-Friendly Zeotropic Blends of CO2/R1234ze(Z) and CO2/R1336mzz(E)

A vapor-liquid phase equilibrium model for binary CO2-H2O and CH4-H2O systems above 523 K for application to fluid inclusions

Composition Analysis of Co2-Nh3-H2o System Based on Raman Spectra

Experimental and an Electrolyte Non-Random Two-Liquid Model to Predict the Vapor–liquid Equilibrium of CO2 in Aqueous Solutions of Diethylenetriamine

Measurement and Thermodynamic Modeling for CO2 Solubility in the N-(2-Hydroxyethyl) Piperazine + Water System

Simulations of vapor–liquid phase equilibrium and interfacial tension in the CO2–H2O–NaCl system

Phase Equilibrium Calculation of Mixtures: Comparison of SAFT, Modified SAFT, and BACK EOS for Supercritical CO2-C2H5OH System

Thermodynamic Model and Process Simulation for CO2 Removal with Low Temperature Methanol

Thermodynamic studies for improving the prediction of CO2 equilibrium solubility in aqueous 2-dimethylamino-2-methyl-1-propanol

Experiment and Modeling of Vapor–liquid Equilibria for H2O+CH3OH+KCl and H2O+CH3OH+NaBr Systems

Thermodynamic Calculations of the Critical Points of the H2–CO2–CH4–CO–H2O System

Density Measurement and PC-SAFT/tPC-PSAFT Modeling of the CO2 + H2O System over a Wide Temperature Range

The CPA Equation of State and an Activity Coefficient Model for Accurate Molar Enthalpy Calculations of Mixtures with Carbon Dioxide and Water/Brine

Predicting Vapor-Liquid Equilibria of CO2+HFC Binary Mixtures by the PR EOS Combined with a Group Contribution Model