Abstract:The solid/gas eutectic unidirectional solidification process is a new kind of technology fabricating the lotus-type porous structure. Besides having the properties of large specific surface area, excellent sound absorption, penetrating performance etc. of traditional porous materials, the particularity of the lotus-type porous structure makes it has extraordinary mechanical and thermal properties. There is a great potential for lotus-type porous aluminum in the field of lightweight engineering and heat dissipation of chip owing to its low density, outstanding corrosion resistance and high thermal conductivity. However, the fabrication of lotus-type porous aluminum has always been been more difficulty than other metals. Until porous aluminum with excellent pore structure was fabricated under very small solidification rates (0.008 similar to 0.015 mm/s) and high superheat degrees of melt (240 similar to 340 K), the proper processing parameters were recognized to be essential for the coupled growth of solid/gas phases for Al-H-2 system, especially the solidification rate. In this work, a three-dimensional time-dependent model describing the evolution of single pore was established based on the theoretical analysis of mass transfer, gas bubble nucleation, pore growth, interruption and detachment. The morphology of single pore under different solidification rates were simulated during the Gasar process by using the finite difference method for Al-H-2 system. The research reveals: coupled growth of solid/gas phases can be achieved under the solidification rates from 0.15 mm/s to 0.005 mm/s. The average pore diameter which ranges from 100 pm to 1100 pm increases with decreasing the solidification rate. The pore length also increases while the pore aspect ratio is nearly a constant about 40 with decreasing the solidification rate. The simulated average pore diameter is in good agreement with the experimental values when solidification rate equals to 0.015 mm/s, and then being slightly lower than the experimental ones with decreasing the solidification rate. The diffusion of hydrogen into the melt during the solidification process is regarded as the main reason of the discrepancy between simulated and experimental average pore diameters. The maximum value of the simulated solidification rates for coupled growth of solid/gas phases in Al-H-2 system first increases from less than 0.01 mm/s to 0.15 mm/s and then being a constant, while the minimum ones increase from about 0.0001 mm/s to 0.01 mm/s with improving the overheat degree of melt and hydrogen partial pressure. By comparing the relative parameters of Al-H-2 and Cu-H-2 systems, the solubility of hydrogen is regarded to be the main parameter which determines solidification rates of coupled growth of solid/gas phases for Al-H-2 system.

Fabrication of Gasar Ingots with Straight Parallel Pores by a Bridgman Method

Influence of Withdrawing Speed on the Porous Structures of Gasar Ingots Fabricated by Bridgman Method

Pore Structure Analysis of Large Size Gasar Cu Ingot Prepared by Bridgman Method

EFFECT OF WITHDRAWING RATE ON PORE MORPHOLOGY OF LOTUS-TYPE POROUS COPPER PRODUCED BY SINGLE-MOLD GASAR TECHNIQUE

The pore growth process and pore coalescence process in Gasar copper

Fabrication of Lotus-Type Porous Micro-Channel Copper by Single-Mold Gasar Technique

Intrinsic Versus Extrinsic Effects on Serrated Flow of Bulk Metallic Glasses

FABRICATION OF REGULAR POROUS MAGNESIUM WITH RADIAL PORE DISTRIBUTION BY 2D GASAR PROCESS

THEORETICAL ANALYSIS ON EFFECT OF TRANSFERENCE VELOCITY ON STRUCTURE OF POROUS METALS FABRICATED BY CONTINUOUS CASTING GASAR PROCESS

FABRICATION OF LOTUS-STRUCTURED POROUS MAGNESIUM WITH GASAR PROCESS

Optimization of multi-directional forging parameters of large-scale Mg-Gd-Y-Zn-Zr alloy forged part guided by finite element simulation

Numerical Simulation of Directionally Solidified Industrial Gas Turbine Hollow Blades by Liquid Metal Cooling

Effect of the Solidification Mode on the Pore Growth of Gasar Porous Mg‐Ag Alloy

Modeling and Numerical Simulation Research on Hollow Steel Ingot Forging Process of Heavy Cylinder Forging

A Steady Solution of the Gasar Eutectic Growth in Directional Solidification

Research on Rotatory Deformation Uniformity and Compaction Effect of Super-heavy Hollow Steel Ingot

Design of variable withdrawal rate for superalloy single-crystal blade fabrication

Effects Of Withdrawal Rate On The Microstructure Of Directionally Solidified Gh4720li Superalloys

MODELING AND SIMULATION OF STRUCTURAL FORMATION OF POROUS ALUMINUM IN GASAR SOLIDIFICATION

Research on Grain Refinement and Homogenization During the Mandrel Stretching Process of a Hollow Steel Ingot Used for Heavy Hydro-Generator Shaft

Computerized simulation of shortened ingots with a controlled crystallization for manufacturing of high-quality forgings