Abstract:With the development in additive manufacturing, the use of surface treatments for gas turbine design applications has greatly expanded. An experimental investigation of the pressure loss and heat transfer characteristics within impingement jet arrays with arrays of target surface micro cooling units is presented. The discharge coefficient and Nusselt number are measured and determined for an evaluation of the pressure loss of the flow system and heat transfer level, respectively. Considered are effects of impingement jet Reynolds number ranging from 1000 to 15,000 and micro cooling units (square pin fin) height (h) with associated values of 0.01, 0.02, 0.05, 0.2, and 0.4 D, where D is the impingement hole diameter. Presented are variations of Nusselt number, and Nusselt number ratio, discharge coefficient, discharge coefficient ratio, discharge coefficient correlation. Depending upon the micro cooling unit height, discharge coefficient ratios slightly decrease with height, and the ratio values generally remain unit value (1.0). When Rej = 1000 and 2500 for several cooling units height values, discharge coefficient ratios show the pressure loss decreases about 2–18% and 3–6%, respectively, when compared to the data of a baseline smooth target surface plate. The observed phenomenon is due to the effects of flow blockage of micro cooing units, local flow separation, and near-wall viscous sublayer reattachment. Results also show that heat transfer levels increase 20–300% for some of the tested toughened target surface plates when compared to smooth target surface plates. The heat transfer level enhancement is because of an increase in thermal transport and near-wall mixing, as well as the increased wetted area. In addition, micro cooling units elements break the viscous sublayer and cause greater turbulence intensity when compared to the smooth target surface. Overall, results demonstrate that the target surface micro cooling units do not result in a visible increment in pressure loss and reduce pressure loss of the flow system for some of the tested patterns. Moreover, results show the significant ability of micro cooling units to enhance the surface heat transfer capability of impingement cooling relative to smooth target surfaces.

Effects of Nozzle Arrangement on Uniformity of Multiple Impinging Jets Heat Transfer in a Fast Cooling Simulation Device

Numerical Study of Heat Flux Reduction Mechanism of the Counterflowing Jet in Rarefied Flows

Effect of the Nozzle Geometry on Flow Field and Heat Transfer in Annular Jet Impingement

Numerical simulation of single-jet impact cooling and double-jet impact cooling of hot-rolled L-shaped steel based on multiphase flow model

Numerical investigation on heat transfer enhancement and surface temperature non-uniformity improvement of spray cooling

Numerical Simulation of the Flow and Heat Transfer Characteristics of Sweeping and Direct Jets on a Flat Plate with Film Holes

Numerical Study and Structural Optimization of Impinging Jet Heat Transfer Performance of Floatation Nozzle

Heat transfer and flow structure characteristics of film-cooled leading edge model with sweeping and normal jets

Modelling Of Impinging Flow And Heat Transfer In A Confined Narrow Gap

NUMERICAL INVESTIGATION OF DIFFERENT TURBULENCE MODELS APPLIED IN COMBINED IMPINGEMENT AND FILM COOLING

Effects Of The Nozzle Exit Section Shape On The Velocity Field And Heat Transfer Of Impinging Synthetic Jets

Numerical Simulation Coupling on Fluid Flow and Heat Transfer in Nozzle and Equipment Cabin of Solid Rocket Motor during Operation Process

Numerical Study on Flow and Heat Transfer Characteristics of 3D Turbulent Impinging Jets

Numerical Study on Stagnation Point Heat Transfer by Jet Impingement in A Confined Narrow Gap

Numerical Simulation and Optimization of Microchannel Heat Sink Combined With Jet Impingement

A developed transition simulation model for turbulent plane jet impingement heat transfer

Numerical Investigation of the Flow and Infrared Radiation Characteristics of Nozzles with Transverse Jets of Different Shapes

Experimental Investigation of Micro Cooling Units on Impingement Jet Array Flow Pressure Loss and Heat Transfer Characteristics

Effect of Reynolds Number, Hole Patterns, Target Plate Thickness on Cooling Performance of an Impinging Jet Array: Part Ii - Conjugate Heat Transfer Results and Optimization

Experimental Investigation of Local and Average Heat Transfer Coefficients under an Inline Impinging Jet Array, Including Jets with Low Impingement Distance and Inclined Angle

Experimental and numerical analysis on thermal-dynamic performance in designed impingement-jet double-layer nested microchannel heat sinks with streaming vertical bifurcations