Abstract:Complex curvature and/or high-stiffened components are often in the elastic-plastic deformation range during the loading stage of creep age forming (CAF) process. Effects of initial stress level, extending from 80 to 210 MPa (typically experienced by large-scale structural components), on the stress relaxation ageing behavior and microstructural evolution of AA2219 alloy have been experimentally investigated by means of stress relaxation ageing tests, tensile tests and scanning transmission electron microscopy. Stress relaxation curves can be mainly divided into two stages: the variable-rate relaxation (VRR) stage and steady-rate relaxation (SRR) stage. When the initial stress levels are less than the yield strength, all stress relaxation curves exhibit a similar decreasing tendency where the stress reduces rapidly in a short VRR stage and then remains almost unchanged for a long SRR stage. Distinctively, the stress relaxation curve whose initial stress is higher than yield strength does not experience the same relaxation law. With increasing initial stress, the duration of the VRR stage extends appreciably and the stress reduction rate during the SRR stage increases. Stress exponent calculation considering the threshold stress suggests the dislocation creep mechanism governs the deformation of stress relaxation. Dislocations induced by loading initial stress are responsible for the significant difference in stress relaxation behavior for different initial stress levels. Besides, age strengthening effect improves with increase in initial stress, as is ascribed to the enhanced precipitation of pre-theta' and theta' phases accompanying conventional GP zones and theta ''. A straightforward, mechanism-based constitutive modeling is established by considering the dislocation and threshold stress. The material constants are calibrated using the experimental data. The initial-stress-level dependence of stress relaxation behavior predicted through the derived constitutive modeling agrees well with the experimental results. The proposed constitutive modeling can be applied to accurately simulate the CAF of large complex structural parts.

The Effect of Stress-Aging on Dimensional Stability Behavior of Al-Cu-Mg Alloy

Effects of Two-Stage Aging on the Dimensional Stability of Al-Cu-Mg Alloy

Effects of Stress-Aging on the Microstructure and Properties of an Aging Forming Al–Cu–Mg–Ag Alloy

Mechanism of Stress Aging in Al-Cu（-Mg-Ag） Alloys

Effect of external stress on the growth of precipitates in Al-Cu and Al-Cu-Mg-Ag alloys

Enhancing Stress Corrosion Cracking Resistance of Low Cu-Containing Al-Zn-Mg-Cu Alloys by Aging Treatment Control

Effects of External Stress During Aging on Microstructure and Properties of AI-Cu-Mg-Ag Alloy

The Effect of SiC Addition on the Dimensional Stability of Al-Cu-Mg Alloy

Effects of External Stress on Aging Precipitation Behavior of Al-Cu-Mg-Ag Alloy

Effects of External Stress Aging on Morphology and Precipitation Behavior of Θ″ Phase in Al-Cu Alloy

Effect of Stress Aging on Mechanical Properties and Microstructures of 2E12 Aluminum Alloy

Influence of Stress‐Aging Processing on Precipitates and Mechanical Properties of a 7075 Aluminum Alloy

Effect of stress coupled with electric field on microstructure of 2524 aluminum alloy

Quantitative study of the effect of stress on the precipitation in an Al-Cu-Mg-Ag alloy single crystal

Effect of Stress on Microstructure and Mechanical Properties during Age Forming Process of 7050 Aluminum Alloy

Effect of Stress Coupled with Electric Field on Aging Dynamics of 2524 Aluminum Alloy

Experimental study on Complex Stress Effect for Stress Relaxation Aging Behavior of Al-Cu-Li Alloy

Stress-relaxation Ageing Behavior and Microstructural Evolution under Varying Initial Stresses in an Al–Cu Alloy: Experiments and Modeling

Evolution of precipitates during two-stage stress-aging of an Al-Zn-Mg-Cu alloy

Quantitative Study of Dimensional Stability Mechanism and Microstructure Evolution During Precipitation Process of 2024al Alloy

Effect of aging route on the precipitation behavior and thermal stability of Al-Cu-Mg-Ag alloy