FPGA-based Layered/enhanced ACO-OFDM Transmitter.

Qibing Wang,Binhuang Song,Bill Corcoran,David Boland,Leimeng Zhuang,Yiwei Xie,Arthur J. Lowery

DOI: https://doi.org/10.1364/ofc.2017.tu3d.6

2017-01-01

Abstract:We present an FPGA-based QPSK-encoded 9.375 Gb/s layered/enhanced ACO-OFDM transmitter giving a high spectral efficiency. The measured Q-factor is greater than 13 dB after 20-km standard single-mode fiber transmission.

What problem does this paper attempt to address?

42.13 Gbit/s 16QAM-OFDM photonics-wireless transmission in 75-110GHz band

Idelfonso Tafur Tafur Monroy

DOI: https://doi.org/10.2528/pier12013006

2012-01-01

Progress In Electromagnetics Research

Abstract:We present a simple architecture for realizing high capacity W-band (75-110 GHz) photonics-wireless system. 42.13 Gbit/s 16QAM-OFDM optical baseband signal is obtained in a seamless 15 GHz spectral bandwidth by using an optical frequency comb generator, resulting in a spectral efficiency of 2.808 bits/s/Hz. Transparent photonic heterodyne up-conversion based on two free-running lasers is employed to synthesize the W-band wireless signal. In the experiment, we program an improved DSP receiver and successfully demonstrate photonics-wireless transmission of 8.9 Gbit/s, 26.7 Gbit/s and 42.13 Gbit/s 16QAM-OOFDM W-band signals, with achieved bit-error-rate (BER) performance below the forward error correction (FEC) limit.
Fiber Wireless Transmission of 8.3-Gb/s/ch QPSK-OFDM Signals in 75–110-Ghz Band

Lei Deng,Marta Beltran,Xiaodan Pang,Xu Zhang,Valeria Arlunno,Ying Zhao,Antonio Caballero,Anton Dogadaev,Xianbin Yu,Roberto Llorente,Deming Liu,Idelfonso Tafur Monroy

DOI: https://doi.org/10.1109/lpt.2011.2179797

IF: 2.6

2012-01-01

IEEE Photonics Technology Letters

Abstract:In this letter, we present a scalable high-speed W-band (75-110-GHz) fiber wireless communication system. By using an optical frequency comb generator, three-channel 8.3-Gb/s/ch optical orthogonal frequency-division-multiplexing (OOFDM) baseband signals in a 15-GHz bandwidth are seamlessly translated from the optical to the wireless domain. The W-band wireless carrier is generated from heterodyne mixing the OOFDM baseband signal with a free-running laser. A W-band electronic down-converter and a digital signal processing-based receiver are used. Three-channel QPSK-OFDM W-band wireless signals are transmitted over 0.5- and 2-m air distance with and without 22.8-km single-mode fiber, respectively, with achieved performance below the forward error correction limit.
Integrated Dual-DFB Laser for 408 GHz Carrier Generation Enabling 131 Gbit/s Wireless Transmission over 10.7 Meters.

Shi Jia,Mu-Chieh Lo,Lu Zhang,Oskars Ozolins,Aleksejs Udalcovs,Deming Kong,Xiaodan Pang,Xianbin Yu,Shilin Xiao,Sergei Popov,Jiajia Chen,Guillermo Carpintero,Toshio Morioka,Hao Hu,Leif K. Oxenlowe

DOI: https://doi.org/10.1364/ofc.2019.th1c.2

2019-01-01

Abstract:A monolithically integrated dual-DFB laser generates a 408 GHz carrier used for demonstrating a record-high single-channel bit rate of 131 Gbit/s transmitted over 10.7 m. 16-QAM-OFDM modulation and specific nonlinear equalization techniques are employed.
The Design and Hardware Implementation of OFDM System Receiver Based on FPGA

Jun Yang,Qing Han,Hongye Li,Wenlong Li

DOI: https://doi.org/10.2991/cmfe-15.2015.194

2015-01-01

Abstract:In recent years, new communication technologies has made rapid development. Orthogo-nal Frequency Division Multiplexing (OFDM) is a core technology in the fourth-generation wireless communication field(4G). The basic principle of OFDM is to split a high-rate data stream into a number of lower. In OFDM system design, a number of parameters are up for consideration, such as the number of subcarriers, guard time, symbol duration, subcarrier spacing, modulation type persubcarrier, and the type of forward error correction coding. The choice of parameters is influenced by system requirements such as available bandwidth, required bit rate, tolerable delay spread, and Doppler values. This paper designs and implements an OFDM receiver system. The system includes interleaving and de-interleaving module, RS encoding and decoding module, QPSK modulation and demodulation module and some system composed of a number of auxiliary modules. This paper analyses and tests efficiency and other factors of the system, and demonstrating the use of FPGA technology enables to receive signal in the OFDM system so well. It has some advantages of occupying less hardware resources, fast running and having good stability.
High-Speed Real-Time Ofdm Transmission Based on Fpga

Xin Xiao,Fan Li,Jianjun Yu

DOI: https://doi.org/10.1117/12.2216268

2016-01-01

Abstract:In this paper, we review our recent research progresses on real-time orthogonal frequency division multiplexing (OFDM) transmission based on FPGA. We successfully demonstrated four-channel wavelength-division multiplexing (WDM) 256.51Gb/s 16-ary quadrature amplitude modulation (16QAM)-OFDM signal transmission system for short-reach optical amplifier free inter-connection with real-time reception. Four optical carriers are modulated by four different 16QAM-OFDM signals via 10G-class direct modulation lasers (DMLs). We achieved highest capacity real-time reception optical OFDM signal transmission over 2.4-km SMF with the bit-error ratio (BER) under soft-decision forward error correction (SD-FEC) limitation of 2.4x10(-2). In order to achieve higher spectrum efficiency (SE), we demonstrate 4-channel high level QAM-OFDM transmission over 20-km SMF-28 with real-time reception. 58.72-Gb/s 256QAM-OFDM and 56.4-Gb/s 128QAM-OFDM signal transmission within 25-GHz grid is achieved with the BER under 2.4x10(-2) and real-time reception.
Generation of optical OFDM signals using 21.4 GS/s real time digital signal processing

Yannis Benlachtar,Philip M Watts,Rachid Bouziane,Peter Milder,Deepak Rangaraj,Anthony Cartolano,Robert Koutsoyannis,James C Hoe,Markus Püschel,Madeleine Glick,Robert I Killey

DOI: https://doi.org/10.1364/OE.17.017658

2009-09-28

Abstract:We demonstrate a field programmable gate array (FPGA) based optical orthogonal frequency division multiplexing (OFDM) transmitter implementing real time digital signal processing at a sample rate of 21.4 GS/s. The QPSK-OFDM signal is generated using an 8 bit, 128 point inverse fast Fourier transform (IFFT) core, performing one transform per clock cycle at a clock speed of 167.2 MHz and can be deployed with either a direct-detection or a coherent receiver. The hardware design and the main digital signal processing functions are described, and we show that the main performance limitation is due to the low (4-bit) resolution of the digital-to-analog converter (DAC) and the 8-bit resolution of the IFFT core used. We analyze the back-to-back performance of the transmitter generating an 8.36 Gb/s optical single sideband (SSB) OFDM signal using digital up-conversion, suitable for direct-detection. Additionally, we use the device to transmit 8.36 Gb/s SSB OFDM signals over 200 km of uncompensated standard single mode fiber achieving an overall BER<10(-3).
High-speed Free-Space Laser Communications Using Advanced Coherent Modulation Formats

Xianglian Feng,Zhihang Wu,Tianshu Wang,Peng Zhang,Xiaoyan Li,Hulin Jiang,Yuwei Su,Hongwei He,Xiaoyan Wang,Shiming Gao

DOI: https://doi.org/10.1109/icocn.2017.8121568

2017-01-01

Abstract:We experimentally demonstrate the high-speed free-space optical (FSO) transmission over 1 km using 20 Gbit/s advanced coherent quadrature phase-shift keying (QPSK) signals. The constellation diagram and the bit error rate (BER) are measured. The receiving sensitivity of the FSO transmission is about-23.9 dBm at the BER of 3.8x10(-3).
Real-time Intra-symbol Two-stage Bit-class Distribution Matcher-based PS-64QAM DMT Transceiver for W-band Wireless Transmission

Long Zhang,Jianjun Yu,Kaihui Wang,Zonghui Zhu,Xiongwei Yang,Luhan Jiang,Jiaxuan Liu,Bohan Sang,Chen Wang,Jianyu Long,Xinda Sun,Yuanxiao Meng,Yumeng Gou,Jingwen Tan,Yikai Wang,Yu Chen,Junjie Ding,Li Zhao,Wen Zhou,Min Zhu,Jianguo Yu

DOI: https://doi.org/10.1109/jlt.2024.3484511

IF: 4.7

2024-01-01

Journal of Lightwave Technology

Abstract:The utilization of probabilistic shaping (PS) techniques effectively mitigates the average power of the transmitted signal by optimizing modulation mapping schemes, which helps to improve the resistance of the wireless transmission system to the nonlinear effect induced by envelope detection. In this work, we have experimentally demonstrated FPGA-based real-time photonics-assisted W-band with envelope detection 23 Gb/s PS 64-ary quadrature amplitude modulation (64QAM) discrete multi-tone (DMT) signals over 40.5-m wireless link. In addition, an intra-symbol two-stage bit-weighted distribution matching-based PS-64QAM scheme was implemented based on FPGA to alleviate nonlinear damage caused by envelope detector. This PS-64QAM scheme has the advantages of no complex multiplication, division operations and low hardware implementation complexity. According to experimental results, by adopting our proposed PS-64QAM scheme, the receiver sensitivity can be significantly improved. This study demonstrates the attainment of the greatest wireless range to date through FPFA-based real-time photonics millimeter wave envelope detection for wireless communication. The results underscore the feasibility of integrating millimeter wave photonics, electronics, and advanced DSP algorithms to accomplish high-speed wireless communication over long distances in real time. This will provide important assistance for our future work in real-time photonics- assisted millimeter wave wireless communication.
Layered ACO-OFDM for Intensity-Modulated Direct-Detection Optical Wireless Transmission.

Qi Wang,Chen Qian,Xuhan Guo,Zhaocheng Wang,David G. Cunningham,Ian H. White

DOI: https://doi.org/10.1364/oe.23.012382

IF: 3.8

2015-01-01

Optics Express

Abstract:Layered asymmetrically clipped optical orthogonal frequency division multiplexing (ACO-OFDM) with high spectral efficiency is proposed in this paper for optical wireless transmission employing intensity modulation with direct detection. In contrast to the conventional ACO-OFDM, which only utilizes odd subcarriers for modulation, leading to an obvious spectral efficiency loss, in layered ACO-OFDM, the subcarriers are divided into different layers and modulated by different kinds of ACO-OFDM, which are combined for simultaneous transmission. In this way, more subcarriers are used for data transmission and the spectral efficiency is improved. An iterative receiver is also proposed for layered ACO-OFDM, where the negative clipping distortion of each layer is subtracted once it is detected so that the signals from different layers can be recovered. Theoretical analysis shows that the proposed scheme can improve the spectral efficiency by up to 2 times compared with conventional ACO-OFDM approaches with the same modulation order. Meanwhile, simulation results confirm a considerable signal-to-noise ratio gain over ACO-OFDM at the same spectral efficiency.
Improved Receiver Design for Layered ACO-OFDM in Optical Wireless Communications

Wang, Q.,zhaocheng wang,xuhan guo,linglong dai

DOI: https://doi.org/10.1109/LPT.2015.2495320

2016-01-01

Abstract:Layered asymmetrically clipped optical orthogonal frequency division multiplexing (LACO-OFDM) is recently proposed for intensity-modulated directed-detected optical wireless communications, which achieves higher spectral efficiency compared with the conventional ACO-OFDM, since different layers of ACO-OFDM signals are combined to utilize more subcarriers. In this letter, an improved receiver is proposed for LACO-OFDM, which distinguishes different layers of ACO-OFDM signals in the time domain. After that, the structure of ACO-OFDM signals in each layer is exploited to further reduce the noise and inter-layer interference, resulting in the improved performance. Simulation results show that the proposed receiver for LACO-OFDM achieves significant gain over its conventional counterpart.
Digital OFDM transmitter architecture and FPGA design

XiaoXin Cui,Dunshan Yu

DOI: https://doi.org/10.1109/ASICON.2009.5351622

2009-01-01

Abstract:OFDM technology is an effective multicarrier technology and is the key technology of HiNOC physical layer standard. In this paper, a digital OFDM transmitter architecture is studied and designed. At system level, algorithm model is constructed with MATLAB. At circuit level, the main function modules such as a 256-point IFFT processor are presented considering implementation complexity. At last, the OFDM transmitter is implemented with ALTERA StratixII FPGA. The testing result shows that transmitter function is correct and performance meets design requirement perfectly.
SNR Improved Digital-Cascaded-pulse-code-modulation Radio-over-fiber Scheme Supporting 16,777,216 QAM for Mobile Fronthaul

Mingxu Wang,Jianjun Yu,Xianming Zhao,Wen Zhou,Kaihui Wang

DOI: https://doi.org/10.1364/jocn.501621

IF: 4.508

2023-01-01

Journal of Optical Communications and Networking

Abstract:We propose a digital-cascaded-pulse-code-modulation radio-over-fiber (DCP-RoF) scheme and verify it experimentally in a coherent transmission system. The 50-Gbaud 2-order 6-bit DCP-RoF signal with a common public radio interface equivalent data rate of ${279}\;{\rm Gb/s/}\lambda$ is successfully transmitted in a 10-km standard single-mode fiber link. Results show that the 2-order 6-bit DCP-RoF scheme achieves a maximum recovered signal-to-noise ratio (SNR) of 83.43 dB, which meets the requirements for 16,777,216-quadrature-amplitude-modulation (16,777,216-QAM) transmission. The DCP-RoF scheme has advantages over analog RoF and digital–analog RoF in terms of SNR improvement, as well as advantages over digital RoF (D-RoF) in spectral efficiency. Furthermore, an average SNR enhancement of 13.48 dB for each linearly increased bandwidth is achieved in the DCP-RoF scheme. Our work suggests many optimistic possibilities for the future radio access networks and mobile fronthaul.
Experimental demonstration of a record high 11.25Gb/s real-time optical OFDM transceiver supporting 25km SMF end-to-end transmission in simple IMDD systems

R P Giddings,X Q Jin,E Hugues-Salas,E Giacoumidis,J L Wei,J M Tang

DOI: https://doi.org/10.1364/OE.18.005541

2010-03-15

Abstract:The fastest ever 11.25Gb/s real-time FPGA-based optical orthogonal frequency division multiplexing (OOFDM) transceivers utilizing 64-QAM encoding/decoding and significantly improved variable power loading are experimentally demonstrated, for the first time, incorporating advanced functionalities of on-line performance monitoring, live system parameter optimization and channel estimation. Real-time end-to-end transmission of an 11.25Gb/s 64-QAM-encoded OOFDM signal with a high electrical spectral efficiency of 5.625bit/s/Hz over 25km of standard and MetroCor single-mode fibres is successfully achieved with respective power penalties of 0.3dB and -0.2dB at a BER of 1.0 x 10(-3) in a directly modulated DFB laser-based intensity modulation and direct detection system without in-line optical amplification and chromatic dispersion compensation. The impacts of variable power loading as well as electrical and optical components on the transmission performance of the demonstrated transceivers are experimentally explored in detail. In addition, numerical simulations also show that variable power loading is an extremely effective means of escalating system performance to its maximum potential.
Transmission of 20-Gb/s Ofdm Signals Occupying 7-Ghz License-Free Band at 60 Ghz Using A Rof System Employing Frequency Sextupling Optical Up-Conversion

Po-Tsung Shih,Chun-Ting Lin,Wen-Jr Jiang,Han-Sheng Huang,Jyehong Chen,Anthony Ng'oma,Michael Sauer,Sien Chi

DOI: https://doi.org/10.1364/oe.18.012748

IF: 3.8

2010-01-01

Optics Express

Abstract:This work describes a proposed 60-GHz radio-over-fiber (RoF) system employing a frequency sextupling optical up-conversion scheme. Based on the modified single sideband modulation scheme, spectrally efficient vector signals were transmitted with no performance degradation due to dispersion-induced fading. Wavelength-division- multiplexed optical up-conversion can be realized using the proposed system. Since the required transmitter bandwidth is significantly reduced, radio-frequency components with lower bandwidth and higher reliability can be utilized. Both 13.75-Gb/s QPSK-OFDM and 20.625-Gb/s 8QAM-OFDM signals were experimentally demonstrated. After transmission over 25-km of standard single mode fiber, no significant received power penalty was observed.
Low-complexity FPGA implementation of 106.24Gbps DP-QPSK coherent optical receiver with fractional oversampling rate based on one FIR filter for resampling, retiming and equalizing

Jingwei Song,Yan Li,Jifang Qiu,Xiaobin Hong,Hongxiang Guo,Zhisheng Yang,Jian Wu

DOI: https://doi.org/10.1109/jlt.2023.3258072

IF: 4.7

2023-01-01

Journal of Lightwave Technology

Abstract:A novel low-complexity combined resampling, retiming and equalizing (RRE) algorithm is proposed. The RRE algorithm uses a single FIR filter for resampling, retiming and equalizing and thus lower the complexity. In the numerical simulation, with an oversampling rate of 32/27, compared to the traditional time-domain scheme with a 15-tap CMA equalizer and the frequency-domain scheme based on 256-point FFT, the RRE algorithm with a 15-tap RRE filter lowers the error vector magnitude (EVM) by 0.036dB and 0.043dB and the complexity is lowered by 48.3% and 31.9%, respectively. In the offline experiment, with a received optical power of -35dBm, compared to the traditional time-domain scheme with a 15-tap CMA equalizer and the frequency-domain scheme based on 256-point FFT, the RRE algorithm with a 15-tap RRE filter lowers the EVM by 0.26dB and 0.36dB. And the RRE algorithm respectively lowers the complexity by 48.3% and 31.9%. The RRE algorithm also enables a real-time 106.24Gbps (26.56GBaud) DP-QPSK coherent optical receiver based on a single FPGA chip using four 6-bit ADCs with a sampling rate of ∼31.48GSa/s. The FPGA-based receiver achieves a sensitivity of -34dBm at BER of 1E-3. As far as we know, this is the highest reported bit rate of a coherent receiver based on a single FPGA chip.

engineering, electrical & electronic,optics,telecommunications
Real-time Demonstration of 12-Λ×800-gb/s Single-carrier 90.5-Gbd DP-64QAM-PCS Coherent Transmission over 1122-Km Ultra-low-loss G.654.E Fiber.

Han Li,Xiuguo Cui,Dawei Ge,Dong Wang,Ruichun Wang,Hongqiang Zou,Zhuo Liu,Dechao Zhang,Minggang Si,Jiang Sun,Yunbo Li,Lixin Gu,Zhiyu Xiao,Jihong Zhu,Ning Wang,Sheng Liu

DOI: https://doi.org/10.1109/ecoc52684.2021.9606039

2021-01-01

Abstract:A record real-time error-free coherent transmission of 12-λ×800-Gb/s single-carrier 90.5-GBd DP-64QAM-PCS signals with a spectral efficiency of 8.0 bit/s/Hz over 1122-km ultra-low-loss large-effective-area G.654.E fiber is experimentally demonstrated for the first time.
Low-Complexity Layered ACO-OFDM for Power-Efficient Visible Light Communications

Ruowen Bai,Steve Hranilovic,Zhaocheng Wang

DOI: https://doi.org/10.1109/tgcn.2022.3147970

2022-01-01

IEEE Transactions on Green Communications and Networking

Abstract:Commercially available LED luminaires demand both low-complexity and high power efficiency from visible light communication (VLC) deployments. Layered asymmetrically clipped optical orthogonal frequency division multiplexing (LACO-OFDM) is attracting increasing interest due to the high spectral efficiency and high power efficiency. However, these advantages come at the price of high computational complexity at both transmitter and receiver. In this paper, we propose a low-complexity LACO-OFDM (L-LACO) to generating identical signals to conventional systems while employing a half-size IFFT/FFT and possessing low implementation complexity. The required number of real-valued multiplication operations and real-valued addition operations are quantified and compared to conventional LACO-OFDM. The saved power corresponding to the reduction in arithmetic operations is also estimated, which is shown to increase logarithmically with number of subcarriers, and to increase linearly with modulation bandwidth. Numerical results show that the proposed L-LACO requires about half the number of arithmetic operations as LACO-OFDM for both the transmitter and the receiver. The BER performance of L-LACO is estimated by Monte Carlo simulations under a VLC line-of-sight (LOS) channel and under a VLC dispersive channel that is shown to be identical to LACO-OFDM.
High Spectral Efficiency 400 Gb/s Transmission by Different Modulation Formats and Advanced DSP

Miao Kong,Xinying Li,Jiao Zhang,Kaihui Wang,Xiangjun Xin,Feng Zhao,Jianjun Yu

DOI: https://doi.org/10.1109/jlt.2019.2932384

IF: 4.7

2019-01-01

Journal of Lightwave Technology

Abstract:We experimentally demonstrate probabilistically shaped 64-ary quadrature-amplitude-modulation (64QAM) 50-GHz-grid wavelength-division-multiplexing (WDM) transmission with a bit rate of 400-Gbit/s per channel over 3,600-km Raman-amplified ultra-large effective area fiber (ULAF). Our results show that the probabilistically shaped 64QAM outperforms the hybrid-32/64QAM by 50% reach improvement. Thanks to pre-equalization and look-up-table pre-distortion, a 5.5-dB optical signal-to-noise ratio (OSNR) gain can be obtained. Furthermore, utilizing ULAF with Raman amplifier causes an apparent improvement on the transmission performance compared with using the SSMF with EDFA. We also compare the optical coupler with the wavelength selective switch utilized in the WDM system to explore a suitable way for WDM transmission. Advanced DSP including Butterworth low-pass digital filter is also used at the receiver end.
A 5-50 Gb/s Quarter Rate Transmitter with a 4-Tap Multiple-Mux Based FFE in 65 Nm CMOS

Xuqiang Zheng,Chun Zhang,Fangxu Lv,Feng Zhao,Shigang Yue,Ziqiang Wang,Fule Li,Zhihua Wang

DOI: https://doi.org/10.1109/esscirc.2016.7598303

2016-01-01

Abstract:This paper presents a 5-50 Gb/s quarter-rate transmitter with a 4-tap feed-forward equalization (FFE) based on multiple-multiplexer (MUX). A bandwidth enhanced 4:1 MUX with the capability of eliminating charge-sharing effect is proposed to increase the maximum operating speed. To produce the quarter-rate parallel data streams with appropriate delays, a compact latch array associated with an interleaved-retiming technique is designed. Implemented in 65 nm CMOS technology, the transmitter occupying an area of 0.6 mm2 achieves a maximum data rate of 50 Gb/s with an energy efficiency of 3.1 pJ/bit.
16Qam Optical Fast-Ofdm Transmission System Based on Discrete Fourier Transform and Frequency Multiplexing

Dongqiang Wang,Cheng Lei,Ruofan Luo,Hongwei Chen,Minghua Chen,Sigang Yang,Shizhong Xie

2014-01-01

Abstract:We demonstrate a QAM-FOFDM system by transmitting the real and imaginary parts separately in different subbands. Each part is modulated by interleaved DFT, which doubles the spectral efficiency than ordinary OFDM.

FPGA-based Layered/enhanced ACO-OFDM Transmitter.

42.13 Gbit/s 16QAM-OFDM photonics-wireless transmission in 75-110GHz band

Fiber Wireless Transmission of 8.3-Gb/s/ch QPSK-OFDM Signals in 75–110-Ghz Band

Integrated Dual-DFB Laser for 408 GHz Carrier Generation Enabling 131 Gbit/s Wireless Transmission over 10.7 Meters.

The Design and Hardware Implementation of OFDM System Receiver Based on FPGA

High-Speed Real-Time Ofdm Transmission Based on Fpga

Generation of optical OFDM signals using 21.4 GS/s real time digital signal processing

High-speed Free-Space Laser Communications Using Advanced Coherent Modulation Formats

Real-time Intra-symbol Two-stage Bit-class Distribution Matcher-based PS-64QAM DMT Transceiver for W-band Wireless Transmission

Layered ACO-OFDM for Intensity-Modulated Direct-Detection Optical Wireless Transmission.

Improved Receiver Design for Layered ACO-OFDM in Optical Wireless Communications

Digital OFDM transmitter architecture and FPGA design

SNR Improved Digital-Cascaded-pulse-code-modulation Radio-over-fiber Scheme Supporting 16,777,216 QAM for Mobile Fronthaul

Experimental demonstration of a record high 11.25Gb/s real-time optical OFDM transceiver supporting 25km SMF end-to-end transmission in simple IMDD systems

Transmission of 20-Gb/s Ofdm Signals Occupying 7-Ghz License-Free Band at 60 Ghz Using A Rof System Employing Frequency Sextupling Optical Up-Conversion

Low-complexity FPGA implementation of 106.24Gbps DP-QPSK coherent optical receiver with fractional oversampling rate based on one FIR filter for resampling, retiming and equalizing

Real-time Demonstration of 12-Λ×800-gb/s Single-carrier 90.5-Gbd DP-64QAM-PCS Coherent Transmission over 1122-Km Ultra-low-loss G.654.E Fiber.

Low-Complexity Layered ACO-OFDM for Power-Efficient Visible Light Communications

High Spectral Efficiency 400 Gb/s Transmission by Different Modulation Formats and Advanced DSP

A 5-50 Gb/s Quarter Rate Transmitter with a 4-Tap Multiple-Mux Based FFE in 65 Nm CMOS

16Qam Optical Fast-Ofdm Transmission System Based on Discrete Fourier Transform and Frequency Multiplexing