Abstract:Hybrid and electric vehicles are becoming increasingly popular due to their benefits in lowering emissions and lower dependency on fossil fuels. A hybrid vehicle battery spends around 70% of its time in storage at different temperatures compared to being cycled. However there is less work on the effect of storage on battery life time than on cycling. Storage life time prediction is often complicated due to interdependency of ageing mechanisms. In particular, storage ageing is difficult to accelerate and moreover, the ageing is not linearly scalable with time. These characteristics are difficult to analyse using a model such as equivalent circuit models which depend heavily on experimental data. Electrochemical models are a feasible option to analyse the chemical and electrical response of a battery under storage conditions. In this work, the Pseudo Two Dimensional Model (P2D) equations are modified to include a continuous solvent reduction reaction responsible for capacity fade. A FORTRAN program is developed and finite volume based formulation is used to discretize the system of equations; electrolyte concentration, solid concentration, solid potential and electrolyte potential coupled with Butler-Volmer kinetics. An unconditionally-stable implicit method is adopted for time dependent calculations; the time discretization has first order accuracy. Mesh generation was done based on the initial radius and battery dimensions. The capability of this model to predict the SEI layer growth and internal resistance increase under different operating condition is used to analyse and quantify the parasitic ageing reactions. The over potential of the side reaction reduces to zero for a storage condition where no external current is applied. The capacity fading solvent reaction parameters are proportional to the interfacial surface area and the side reaction exchange current density. Thus the critical parameter controlling the rate of SEI layer growth is the side reaction exchange current density. Another important parameter is the temperature of the battery which is found to accelerate cell ageing. However, in this initial work, the analysis is limited to iso-thermal conditions since the dependency of temperature on cell performance is complex . The storage experiment can be divided into two main parts, the characterisation and the storage test. For the first one, an ESPEC thermal chamber has been used to control temperature and humidity level. For storage test, the cells are stored at 25 ° C at three different SoC values, 20%, 50% and 90% and the capacity characterisation test has been performed after 73, 139, 202 and 297 days to calculate the capacity of the cell. The side reaction coefficient in the electrochemical model was adjusted to match the experimental data for the first point after 73 days. The capacity at the remaining points are predicted based on this initial parameterisation. Conclusions about the parasitic reaction are made based on the variation side reaction exchange current density. The storage results are also used to fine tune the SEI properties and the influence of storage on capacity fading side reaction is investigated for the first time using an electrochemical model. This work establishes a guideline for calculating the SEI properties based on storage ageing experimentation where the driving potential is nearly zero. The results presented in this work can be used as a guiding tool for better battery design for different storage profiles. Figure 1

Degradation Analysis of Commercial Lithium-Ion Battery in Long-Term Storage

Comprehensive Aging Model Coupling Chemical and Mechanical Degradation Mechanisms for NCM/C6-Si Lithium-Ion Batteries

Investigation of Lithium-Ion Battery Nonlinear Degradation by Experiments and Model-Based Simulation

Quantitative Analysis of Degradation Modes of Lithium-Ion Battery under Different Operating Conditions

EXAMINATION OF LITHIUM-ION BATTERY PERFORMANCE DEGRADATION UNDER DYNAMIC ENVIRONMENT AND EARLY DETECTION OF THERMAL RUNAWAY WITH INTERNAL SENSOR MEASUREMENT

Mathematical Models for the Performance Degradation of Lithium-Ion Batteries with Different Status of Charge (SOC) in Long-Term High Temperature Storage

The Degradation Behavior of LiFePO4/C Batteries during Long-Term Calendar Aging

Investigation of Lithium-Ion Battery Degradation Mechanisms by Combining Differential Voltage Analysis and Alternating Current Impedance

In Situ Monitoring of Lithium-Ion Battery Degradation Using an Electrochemical Model

Aging Mechanism Analysis And Its Impact On Capacity Loss Of Lithium Ion Batteries

Aging mechanism diagnosis of lithium ion battery by open circuit voltage analysis

Capacity Degradation and Aging Mechanisms Evolution of Lithium-Ion Batteries under Different Operation Conditions

Aging Mechanisms and Evolution Patterns of Commercial LiFePO4 Lithium-Ion Batteries

Degradation Diagnostics of Lithium-Ion Batteries Cycled Under Varying Conditions

A Physics-Based Aging Model for Lithium-Ion Battery with Coupled Chemical/mechanical Degradation Mechanisms

A Coupled Electrochemical-Thermal-mechanical Degradation Modelling Approach for Lifetime Assessment of Lithium-Ion Batteries

Development of a lifetime prediction model for lithium thionyl chloride batteries based on an accelerated degradation test.

Prediction of Storage Ageing in a Lithium Ion Battery Using an Electrochemical Model

Analysis of Performance Degradation in Lithium-Ion Batteries Based on a Lumped Particle Diffusion Model

Aging Mechanisms of Lithium-ion Batteries

Effect of Aging Path on Degradation Characteristics of Lithium-Ion Batteries in Low-Temperature Environments