Abstract:Hybrid and electric vehicles are becoming increasingly popular due to their benefits in lowering emissions and lower dependency on fossil fuels. A hybrid vehicle battery spends around 70% of its time in storage at different temperatures compared to being cycled. However there is less work on the effect of storage on battery life time than on cycling. Storage life time prediction is often complicated due to interdependency of ageing mechanisms. In particular, storage ageing is difficult to accelerate and moreover, the ageing is not linearly scalable with time. These characteristics are difficult to analyse using a model such as equivalent circuit models which depend heavily on experimental data. Electrochemical models are a feasible option to analyse the chemical and electrical response of a battery under storage conditions. In this work, the Pseudo Two Dimensional Model (P2D) equations are modified to include a continuous solvent reduction reaction responsible for capacity fade. A FORTRAN program is developed and finite volume based formulation is used to discretize the system of equations; electrolyte concentration, solid concentration, solid potential and electrolyte potential coupled with Butler-Volmer kinetics. An unconditionally-stable implicit method is adopted for time dependent calculations; the time discretization has first order accuracy. Mesh generation was done based on the initial radius and battery dimensions. The capability of this model to predict the SEI layer growth and internal resistance increase under different operating condition is used to analyse and quantify the parasitic ageing reactions. The over potential of the side reaction reduces to zero for a storage condition where no external current is applied. The capacity fading solvent reaction parameters are proportional to the interfacial surface area and the side reaction exchange current density. Thus the critical parameter controlling the rate of SEI layer growth is the side reaction exchange current density. Another important parameter is the temperature of the battery which is found to accelerate cell ageing. However, in this initial work, the analysis is limited to iso-thermal conditions since the dependency of temperature on cell performance is complex . The storage experiment can be divided into two main parts, the characterisation and the storage test. For the first one, an ESPEC thermal chamber has been used to control temperature and humidity level. For storage test, the cells are stored at 25 ° C at three different SoC values, 20%, 50% and 90% and the capacity characterisation test has been performed after 73, 139, 202 and 297 days to calculate the capacity of the cell. The side reaction coefficient in the electrochemical model was adjusted to match the experimental data for the first point after 73 days. The capacity at the remaining points are predicted based on this initial parameterisation. Conclusions about the parasitic reaction are made based on the variation side reaction exchange current density. The storage results are also used to fine tune the SEI properties and the influence of storage on capacity fading side reaction is investigated for the first time using an electrochemical model. This work establishes a guideline for calculating the SEI properties based on storage ageing experimentation where the driving potential is nearly zero. The results presented in this work can be used as a guiding tool for better battery design for different storage profiles. Figure 1

Development of a lifetime prediction model for lithium thionyl chloride batteries based on an accelerated degradation test.

Design and Validation of Lifetime Prediction Model for Lithium-Thiocarbonyl Chloride Batteries Based on Accelerated Aging Experiments

Comprehensive Aging Model Coupling Chemical and Mechanical Degradation Mechanisms for NCM/C6-Si Lithium-Ion Batteries

Life Prediction of Lithium Thionyl Chloride Batteries Based on the Pulse Load Test and Accelerated Degradation Test

A Semi-Empirical Capacity Degradation Model of EV Li-Ion Batteries Based on Eyring Equation

Investigation of Lithium-Ion Battery Nonlinear Degradation by Experiments and Model-Based Simulation

Empirical prediction model for Li/SOCl2 cells based on the accelerated degradation test.

A Coupled Electrochemical-Thermal-mechanical Degradation Modelling Approach for Lifetime Assessment of Lithium-Ion Batteries

A Novel Dual Time Scale Life Prediction Method for Lithium‐ion Batteries Considering Effects of Temperature and State of Charge

Degradation Analysis of Commercial Lithium-Ion Battery in Long-Term Storage

A self‐adaptive, data‐driven method to predict the cycling life of lithium‐ion batteries

Life Extrapolation Model for Lithium-ion Battery with Accelerated Degradation Test

A practical semi-empirical model for predicting the SoH of lithium-ion battery: A novel perspective on short-term rest

Prediction of Storage Ageing in a Lithium Ion Battery Using an Electrochemical Model

Simplified modeling and parameter estimation to predict calendar life of Li-ion batteries

Lithium-ion battery degradation: using degradation mode analysis to validate lifetime prediction modelling

Electrochemical Model Boosting Accurate Prediction of Calendar Life for Commercial LiFePO4|graphite Cells by Combining Solid Electrolyte Interface Side Reactions

A semi-empirical model of the calendar ageing of lithium-ion batteries aimed at automotive and deep-space applications

Design and Application: Simplified Electrochemical Modeling for Lithium-ion Batteries in Whole Lifespan

Integrating Physics-Based Modeling and Machine Learning for Degradation Diagnostics of Lithium-Ion Batteries

Accelerated aging of lithium-ion batteries: bridging battery aging analysis and operational lifetime prediction