Abstract:Ultrasonic additive manufacturing (UAM) is now extensively used in advanced materials processing since it applies ultrasonic frequency vibrations locally pressed on the metal parts to make them deformed and/or joined. In the field of electronic packaging, wirebonding is such a kind of type, especially such as ultrasonic wedge bonding, which combines ultrasonic and pressure only, without heating during the bonding process. Through high frequency vibrations, the metal ribbons or wires were interconnected with substrates within mille-seconds. Without ultrasounds, commonly it needs more heat or pressures. One of the most important mechanisms is focused on the effects of ultrasonic-induced deformation structures in the metals. Previously, we have observed the evolution of the textures and grains, but there have not been found any data on the report of nanoscale features of the metal itself. Therefore, in the present study, by using high-resolution transmission electron microscope (HR-TEM) pure coarse-grained aluminum was chosen for investigating the deformation microstructures and mechanism when exposed under ultrasonic vibrations at room temperature. It was found that deformed pure aluminum wire has equiaxial grain shape, and recrystallization grains are evident since there has little defects in them. But within some grains, sub-structures can be found. HR-TEM observation reveals that these sub-structures can be defined as sub-grains with diameter of a few nanometers. Further, it is the first that large stacking faults (SFs) with a width longer than 15 nm and even microtwins can be seen clearly. Their distribution mainly aligns parallelly or with an angle of about 70 degree. Increasing ultrasonic power seems enlarge these SFs. Cyclic vibrations contribute to the formation of these SFs/microtwins.

High-strain-rate Deformation in Ultrasonic Additive Manufacturing

Micro Pin Extrusion of Metallic Materials Assisted by Ultrasonic Vibration

Intrinsic Dependence of Welding Quality and Recrystallization on the Surface-Contacted Micro-Asperity Scale During Ultrasonic Welding of Cu–Cu Joints

Dynamic Recrystallization and Recovery in Very High‐Power Ultrasonic Additive Manufacturing

Investigation of the Effect of Artificial Internal Defects on the Tensile Behavior of Laser Powder Bed Fusion 17–4 Stainless Steel Samples: Simultaneous Tensile Testing and X-Ray Computed Tomography

Ultrasonic-induced amorphization and strengthening mechanisms of ultrasonic vibrations assisted friction stir Al/Ti welds

Strengthening Effects at Dissimilar Metal Interfaces Created by Ultrasonic Additive Manufacturing

Microstructure and Lap Shear Strength of the Weld Interface in Ultrasonic Welding of Al Alloy to Stainless Steel

Microstructure Evolution of 1100 Al Alloy Multi-Foils During Ultrasonic Additive Manufacturing

Influence of ultrasonic parameters on microstructural refinement and defect elimination in ultrasound-assisted laser-based metal additive manufacturing

Ultrasonic-induced Deformation Nanostructures in Coarse-Grained Aluminum Wires at Room Temperature

In-situ study of tensile behavior of Ti/Al laminated metal composites fabricated via ultrasonic additive manufacturing

Microstructure Characterization and Mechanism of Acoustoplastic Effect in Friction Stir Welding Assisted by Ultrasonic Vibrations on the Bottom Surface of Workpieces

Effect and mechanism of inter-layer ultrasonic impact strengthening on the anisotropy of low carbon steel components fabricated by wire and arc additive manufacturing

Influence of the Coarse Grain Structure of a Titanium Alloy Ti-4Al-3V Formed by Wire-Feed Electron Beam Additive Manufacturing on Strain Inhomogeneities and Fracture

Constitutive Behavior and Microstructural Evolution in Ultrasonic Vibration Assisted Deformation of Ultrathin Superalloy Sheet

Numerical study of the ultrasonic impact on additive manufactured parts

Grain refinement and mechanical properties improvement of Inconel 625 alloy fabricated by ultrasonic-assisted wire and arc additive manufacturing

In-situ Observation of Twinning and Grain Rotation Assisted Deformation in Wire-Arc Direct Energy Deposited (WDED) Single Phase Titanium

Understanding the strain localization in additively manufactured materials: Micro-scale tensile tests and crystal plasticity modeling

Progress in the Effect of Ultrasonic Impact Treatment on Microstructure Improvement and Strengthening Mechanism in Additive Manufacturing