Abstract:Ti–6Al–4V alloy samples with two bi-lamellar microstructures were prepared by cost-effective thermomechanical powder consolidation and two inter-critical annealing treatments; one comprising of annealing at 900 °C followed by air cooling (900-AC alloy) and the other comprising of annealing at 910 °C followed by water quenching and aging (910-Q&A alloy), respectively. Both bi-lamellar microstructures encompass lamellae of primary α phase and β transformed structure which consists of ultrathin secondary α lamellae and β thin layers. Thanks to the higher Al concentration in the primary α lamellae associated with the higher annealing temperature and finer scale of βt structure lamellae, the α and βt lamellae of the 910-Q&A alloy exhibit a higher nano-hardness than that of the 900-AC alloy (5.4 and 4.6 GPa vs. 4.5 and 4.3 GPa) as well as a larger difference in nano-hardness between the α and βt lamellae (0.8 vs. 0.2 GPa). These microstructural and nano-hardness differences lead to a significant enhancement of the yield strength of the 910-Q&A alloy by 200 MPa compared to the 900-AC alloy with almost no decrease of tensile ductility. Quantitative analysis indicates that the hardening of α and βt lamellae accounted for approximately 35% and 28% of the total strength increment, respectively, while the heterostructure induced hardening associated with the inhomogeneity between the α and βt lamellae accounts for approximately 37% of the strength increment. Interestingly, the significantly higher flow stress of the 910-Q&A alloy during tensile deformation induces a significant higher degree of trans-lamellar twinning which is believed to be responsible for mitigating the strain localization and maintaining the good tensile ductility despite of a higher flow stress.

Ultrahigh strength and large plasticity of nanostructured Ti62Nb12.2Fe13.6Co6.4Al5.8 alloy obtained by selectively controlled micrometer-sized phases

Strong and ductile nanoscale Ti-1Fe dual-phase alloy via deformation twinning

A new insight into high-strength Ti 62 Nb 12.2 Fe 13.6 Co 6.4 Al 5.8 alloys with bimodal microstructure fabricated by semi-solid sintering

Mechanical properties and deformation mechanisms of Ti-15 Nb-5Zr-4Sn-1Fe alloy with varying α phase fraction

Achieving super-high strength and acceptable plasticity for a near β-type Ti-4.5Mo-5.1Al-1.8Zr-1.1Sn-2.5Cr-2.9Zn alloy through manipulating hierarchical microstructure

A hierarchical nanolamella-structured alloy with excellent combinations of tensile properties

Achieving superior strength-ductility combination in the heterogeneous microstructured Ti64 alloy via multi-eutectoid elements alloying with CoCrFeNiMn during laser powder bed fusion

Microstructure evolution, hot deformation behavior and mechanical properties of Ti-43Al-6Nb-1B alloy

Enhancing Strength and Ductility of a Ni-26.6Co-18.4Cr-4.1Mo-2.3Al-0.3Ti-5.4Nb Alloy via Nanosized Precipitations, Stacking Faults, and Nanotwins

Synthesis of TiAl/Nb Composites with Concurrently Enhanced Strength and Plasticity by Powder Metallurgy

Solidification Microstructure Evolution and Mechanical Properties of Casting Ti-48Al-2Cr-2Nb-(Ni,TiB2)Alloy

A Hierarchical and Multiphase Nanolaminated Alloy with an Excellent Combination of Tensile Properties

The α 2 to orthorhombic O-phase transformation-facilitated high elastically mediated strain transfer ability in high Nb-TiAl alloys

A Novel High-Strength Β-Ti Alloy with Hierarchical Distribution of Α-Phase: the Superior Combination of Strength and Ductility

High-Strength Nanotwinned Al Alloys with 9R Phase

Strength enhancement of a bi-lamellar PM Ti–6Al–4V alloy without sacrificing ductility by Al partitioning and twinning-induced plasticity effect

High Strength and Deformation Stability Achieved in CrCoNi Alloy Containing Deformable Oxides

Enhanced yield strength by fine grain strengthening and TRIP/TWIP effect of metastable β-type Ti-4V-2Mo-2Fe alloy with high ductility

Ultrafine Composite Microstructure in a Bulk Ti Alloy for High Strength, Strain Hardening and Tensile Ductility

Simultaneously Enhancing the Strength and Ductility of Lamellar Ti–6Al–4V Alloy Via Designing Hierarchical 3D Nanolayered Structure

Equiaxed Ti-based Composites with High Strength and Large Plasticity Prepared by Sintering and Crystallizing Amorphous Powder