Abstract:Electron beam selective melting (EBM) and selective laser melting (SLM) are regarded as significant manufacturing processes for near-net-shaped Ti6Al4V components. Generally, in the conventional EBM process, preheating is necessitated to avoid “smoke” caused by the charging of electrons. In the conventional SLM process, laser as an energy source without the risk of “smoke” can be employed to melt metal powder at low temperatures. However, because of the low absorption rate of laser, the powder bed temperature cannot reach a high level. It is difficult to obtain as-built TiAl4V with favorable comprehensive properties via conventional EBM or SLM. Hence, two types of electron beam and laser hybrid preheating (EB-LHP) combined with selective melting strategies are proposed. Using laser to preheat powder allows EBM to be performed at a low powder bed temperature (EBM-LT), whereas using an electron beam to preheat powder allows SLM to be performed at a high powder bed temperature (SLM-HT). Ti6Al4V samples are fabricated using two different manufacturing strategies (i.e., EBM-LT and SLM-HT) and two conventional processes, i.e., EBM at a high powder bed temperature (EBM-HT) and SLM at a low powder bed temperature (SLM-LT). The temperature-dependent surface quality, microstructure, density, and mechanical properties of the as-built Ti6Al4V samples are characterized and compared. Results show that EBM-LT Ti6Al4V exhibits a higher ultimate tensile strength (981±43 MPa) and a lower elongation (12.2%±2.3%) than EBM-HT Ti6Al4V owing to the presence of α′ martensite. The SLM-HT Ti6Al4V possesses the highest ultimate tensile strength (1,059±62 MPa) and an elongation (14.8%±4.0%) comparable to that of the EBM-HT Ti6Al4V (16.6%±1.2%).

Effect of Energy Input on Microstructure and Mechanical Properties in EBSM Ti6Al4V

Microstructures Of Components Synthesized Via Electron Beam Selective Melting Using Blended Pre-Alloyed Powders Of Ti6al4v And Ti45al7nb

Effect of Process Parameters on Microstructure of TiAl Alloy Produced by Electron Beam Selective Melting

Effects of scanning parameters on material deposition during Electron Beam Selective Melting of Ti-6Al-4V powder

Microstructures Of Ti6a14v Components Synthesized Via Electron Beam Selective Melting

Micromechanical testing and microstructure analysis of as-welded and post-weld heat-treated Ti-6Al-4V alloy

Effect of Heat Treatment on Microstructure and Tensile Properties of Ti-6Al-4V Alloy Produced by Coaxial Electron Beam Wire Feeding Additive Manufacturing

Comparison of the microstructures and mechanical properties of Ti–6Al–4V fabricated by selective laser melting and electron beam melting

Diverse microstructure of Ti6.5Al2Zr1Mo1V fabricated via electron beam selective melting

The Influence of Electron Beam Welding on the Microstructure of Ti-6Al-4V Alloy Produced by Selective Laser Melting Technology

Effect of Hot Isostatic Pressing and Solution Heat Treatment on the Microstructure and Mechanical Properties of Ti-6Al-4V Alloy Manufactured by Selective Laser Melting

Electron Beam Impact on Microstructure and Microhardness of Ti–6Al–4V Titanium Alloy Produced by Wire Electron-Beam Additive Manufacturing Technology and Selective Laser Alloying at Simulation of Electronic-Beam Welding

Effect of Direct Rolling Process on Microstructure and Mechanical Properties of the Electron Beam Cold Hearth Melting Ti-6Al-4V Alloy

Performance of Ti6Al4V fabricated by electron beam and laser hybrid preheating and selective melting strategy

Hierarchical microstructure of a titanium alloy fabricated by electron beam selective melting

The role of defects and characterisation of tensile behaviour of EBM Additive manufactured Ti-6Al-4V: An experimental study at elevated temperature

Microstructure and Microhardness of Electron Beam Melted Ti-6Al-4V Components with Differential Thickness in Initial Deposition Layers

Mechanical and Electrochemical Properties Comparison of Additively Manufactured Ti-6Al-4V Alloys by Electron Beam Melting and Selective Laser Melting

Evolution of microstructure and mechanical properties in the molten pool of γ-TiAl alloy synthesized in situ by dual-wire-fed electron beam directed energy deposition.

Graded microstructure and mechanical properties of additive manufactured Ti–6Al–4V via electron beam melting

Ti-48Al-2Cr-2Nb alloys prepared by electron beam selective melting additive manufacturing: microstructural and tensile properties