Abstract:Abstract Background It is known that a number of parameters can influence the post-printing properties of bone tissue scaffolds. Previous research has primarily focused on the effect of parameters associated with scaffold design (e.g., scaffold porosity) and specific scaffold printing processes (e.g., printing pressure). To our knowledge, no studies have investigated variations in post-printing properties attributed to the techniques used to synthesize the materials for printing (e.g., melt-blending, powder blending, liquid solvent, and solid solvent). Methods Four material preparation techniques were investigated to determine their influence on scaffold properties. Polycaprolactone/nano-hydroxyapatite 30% (wt.) materials were synthesized through melt-blending, powder blending, liquid solvent, and solid solvent techniques. The material printability and the properties of printed scaffolds, in terms of swelling/degradation, mechanical strength, morphology, and thermal properties, were examined and compared to one another using Kruskal-Wallis nonparametric statistical analysis. Results Material prepared through the liquid solvent technique was found to have limited printability, while melt-blended material demonstrated the highest degree of uniformity and lowest extent of swelling and degradation. Scaffolds prepared with powder-blended material demonstrated the highest Young’s modulus, yield strength, and modulus of resilience; however, they also demonstrated the highest degree of variability. The higher degree of inhomogeneity in the material was further supported by thermal gravimetric analysis. While scaffolds printed from melt-blended, powder-blended, and solid solvent materials demonstrated a high degree of micro-porosity, the liquid solvent material preparation technique resulted in minimal micro-porosity. Conclusions Study results indicate that specific techniques used to prepare materials influence the printing process and post-printing scaffold properties. Among the four techniques examined, melt-blended materials were found to be the most favorable, specifically when considering the combination of printability, consistent mechanical properties, and efficient preparation. Techniques determined to be favourable based on the properties investigated should undergo further studies related to biological properties and time-dependent properties beyond 21-days.

Molecular Dynamics Simulation Study of the Structures and Properties of Three Polymer Binders

Structures and properties of polymer binders PVP ,PAM and PVA by a molecular dynamics simulation method

Molecular Dynamics Simulation and Experimental Study of the Bonding Properties of Polymer Binders in 3D Powder Printed Hydroxyapatite Bioceramic Bone Scaffolds

Study the Bonding Mechanism of Binders on Hydroxyapatite Surface and Mechanical Properties for 3dp Fabrication Bone Scaffolds

The printability of three water based polymeric binders and their effects on the properties of 3D printed hydroxyapatite bone scaffold

3D-Printed Bioceramic Scaffolds with High Strength and High Precision

Study on the Mechanical Properties of Three-Dimensional Directly Binding Hydroxyapatite Powder

Calcium silicate/polyvinyl/chitosan/alginate-based bioceramic slurry for 3D printing of scaffolds: Interfacial interactions – Mechanical properties relationship

Molecular Dynamics Simulations for the Examination of Mechanical Properties of Hydroxyapatite/ Poly Α-N-butyl Cyanoacrylate under Additive Manufacturing

A Study of the Mechanical Properties of the NEPE Binders by Molecular Dynamic Simulations and Experiments

Molecular Dynamic Simulations and Experiments Study on the Mechanical Properties of HTPE/PEG Interpenetrating Polymer Network (IPN) Binders

Study of the bio-nanofluid heat transfer rate and thermo-physical properties of fused deposition modeling of bone scaffold dip-coated by polyvinyl alcohol/nano-diopside

Research status and development trend of 3D printing binders

Preparation and performance of poly (vinyl alcohol)/polylactic acid/hydroxyapatite composite scaffolds based on 3D printing

Structural Mechanical Properties of 3D Printing Biomimetic Bone Replacement Materials

Fabrication and Properties of Poly(vinyl Alcohol)/β-Tricalcium Phosphate Composite Scaffolds Via Fused Deposition Modeling for Bone Tissue Engineering

Shear thinning molecular dynamics simulation of binder solution for 3D printing alumina

3D printing PCL/nHA bone scaffolds: exploring the influence of material synthesis techniques

Molecular dynamics simulation on mechanical properties of PVP/PVA

Advanced Bioresin Formulation for 3D-Printed Bone Scaffolds: PCLDMA and p-PLA Integration

Advances in Filament Structure of 3D Bioprinted Biodegradable Bone Repair Scaffolds