Mechanism of Aging Effect in Hybrid-Doped Batio3 Ceramics: Electronegativity and Ionic Radius

Dingyue Hu,Sen Yang,Chao Zhou,Lixue Zhang,Wenfeng Liu,Wei Chen,Xiaobing Ren

DOI: https://doi.org/10.1039/c6ra23546h

IF: 4.036

2016-01-01

RSC Advances

Abstract:In hybrid-doped BaTiO3 ceramics, acceptor (A3+) with higher ER tends to form defect pairs with donors (D5+ or D3+).

What problem does this paper attempt to address?

Kinetics Controlled Aging Effect of Ferroelectricity in Al-Doped and Ga-Doped Batio3

Y. Y. Guo,M. H. Qin,T. Wei,K. F. Wang,J. -M. Liu

DOI: https://doi.org/10.1063/1.3490700

IF: 4

2010-01-01

Applied Physics Letters

Abstract:Our experiments on ferroelectric aging of Al3+- and Ga3+-doped BaTiO3 ceramics reveal the crucial role of migration kinetics of point defects (oxygen vacancies) besides the thermodynamic driving force based on the symmetry conforming short-range ordering scenario. The doping with Ga3+ or tiny Al3+ ions shows the clear aging effect, while the high-level Al3+-doping suppresses the aging effect. The suppression is mainly attributed to the kinetically limited migration of oxygen vacancies due to the lattice shrinkage, while the other mechanisms may also make sense.
External Field Effects on Aging Phenomenon of Acceptor-Doped BaTiO3 Ceramics

Y. Y. Guo,J. -M. Liu,Y. F. Guo,T. Wei,Y. J. Guo,N. Zhang

DOI: https://doi.org/10.1063/1.4930259

IF: 1.697

2015-01-01

AIP Advances

Abstract:Our experiments on ferroelectric aging phenomena of a series of acceptor-doped BaTiO3 ceramics demonstrate that after well-aging, all samples show a similar double hysteresis loop under smaller applied electric field, regardless of ionic radius or ionic valence of the acceptor. However, with increasing the applied electric field, the completely constricted loops gradually start to open, indicating the aging effect becomes weak under larger electric field. The unified microscopic mechanism responsible for the similar aging behavior in different acceptor-doped BaTiO3 ceramics may be that the larger field is considered to kinetically facilitate a part of oxygen vacancies short-range hopping. As a result, the defect dipole field provided by oxygen vacancies and the associated defect dipoles frozen in the original states decreases, thus contributing to the weaker aging effect.
Nonmonotonic Variation of Aging Behavior in Fe-doped BaTiO3 Ceramics

Fengzhen Huang,Zhenghao Jiang,Xiaomei Lu,Ruixia Ti,Huarui Wu,Yi Kan,Jinsong Zhu

DOI: https://doi.org/10.1063/1.4890383

IF: 4

2014-01-01

Applied Physics Letters

Abstract:The investigation of ferroelectric aging effect in Fe-doped BaTiO3 ceramics reveals that such effect is first strengthened and then suppressed with the increase content of Fe dopant. Such nonmonotonic variation of aging behavior is considered to be originated from the competition effects between increased concentration of oxygen vacancies and decreased c/a value on the formation of defect dipoles (FeTi′−Vo··)·. This study provides a feasible alternative method for modulating aging effect and will favor the applications of ferroelectrics.
Influence of Bao-Cao-Sio2 on Dielectric Properties and Reliability of Batio3-Based Ceramics

Qiancheng Zhao,Huiling Gong,Xiaohui Wang,Bingcheng Luo,Longtu Li

DOI: https://doi.org/10.1002/pssa.201532706

2015-01-01

physica status solidi (a)

Abstract:The dielectric properties and resistance degradation behavior of BCG‐doped BaTiO3‐based ceramics were investigated, where BCG consists of BaO, CaO, and SiO2. In oxide ceramics, oxygen vacancies have an important effect on degradation behaviors. X‐ray diffraction was employed to analyze the occupancy of Ca2+ in the Ba sites or Ti sites with different BCG contents. For the light‐doped, Ca2+ mainly occupy the Ba sites resulting in a decrease of lattice parameters and thus an increase in the enthalpy of reduction which might limit the concentration of oxygen vacancies. However, acceptor defects, Ca″Ti which could trap the forming electrons at room temperature but deteriorate the resistance degradation behavior at high temperature, would be generated with excessive BCG contents. Moreover, thermally stimulated depolarization current (TSDC) analysis was carried out to analyze the defect relaxation behavior and the actual concentration. The resistance degradation can be correlated with the depolarization current strength (Jmax) and the relaxation temperature (Tm) versus polarization condition.
Enhanced dielectric and ferroelectric properties of the hybrid-doped BaTiO3 ceramics by the semi-solution method

Jinghan Gao,Wenfeng Liu,Lei Zhang,Fanyi Kong,Yi Zhao,Shengtao Li

DOI: https://doi.org/10.1016/j.ceramint.2021.02.136

IF: 5.532

2021-06-01

Ceramics International

Abstract:In the present study, an industrially viable ceramics fabrication way based on solid-state reaction method–semi-solution method was used to improve the dielectric and ferroelectric properties of acceptor-donor co-doped BaTiO3 ceramics. Unlike the conventional solid-state reaction method, additives in the semi-solution method were introduced in the form of the aqueous solution rather than oxide powders. Experiment results show that higher peak dielectric constant <math>εmax</math> (140–150%), larger maximum polarization <math>Pmax</math> (24 μC cm−2), and less apparent aging phenomena were achieved by the semi-solution method. A comprehensive microscopic analysis was carried out to explore the origin of property enhancement. Results show that enhanced properties could be ascribed to the higher level of compositional homogeneity and lower content of oxygen vacancies. This study provides a new method to control aging phenomena and achieve property enhancement in acceptor-donor co-doped ceramics. Moreover, this simple and cost-effective method may also find its application in other extensive-doped ceramics.

materials science, ceramics
Study of the Defect Chemistry of Ca-Doped Batio3 Ceramics

XW ZHANG,Y WANG,LT LI

DOI: https://doi.org/10.1080/00150199008016501

1990-01-01

Ferroelectrics

Abstract:The characteristics of Ca2+ in BaTiO3 are of considerable interest. In this paper, measurements of high temperature equilibrium conductivity and positron annihilation have been used to analyze the effects of two kinds of substitution (equivalent and nonequivalent) of Ca2+ on the defect structure and electrical properties of BaTiO3. The results show that the equivalent substitution of Ca2+ can change the enthalpy of oxidation and reduction reactions in different directions. The partial occupation of the Ti-site by Ca2+ causes a marked influence on the electrical conductivity and positron lifetime of BaTiO3. The solid solubility of Ca2+ at the Ti-site of BaTiO3 is confirmed by the analysis of defect chemistry and the positron annihilation technique. Equivalent substitution of Ca2+ has no substantial effect on the resistivity of BaTiO3 sintered in a reducing atmosphere. A small amount of Ca2+ ions incorporated into the Ti-site may increase the resistivity of BaTiO3 by more than ten orders of magnitude for material sintered in a strongly reducing atmosphere. The material can further be improved for use in monolithic capacitors with base-metal electrodes.
Defect Dipoles Induced High‐energy Storage Density in Mn‐doped BST Ceramics Prepared by Spark Plasma Sintering

Yu Hui Huang,Bing Liu,Xiao Qiang Liu,Juan Li,Yong Jun Wu

DOI: https://doi.org/10.1111/jace.16088

IF: 4.186

2018-01-01

Journal of the American Ceramic Society

Abstract:Ba0.5Sr0.5TiO3 ceramics with different Mn-doping amount (Ba0.5Sr0.5Ti1-xMnxO3, x = 0, 0.1%, 0.3%, 0.5%) were prepared by spark plasma sintering method. The single phase with cubic structure symmetry was confirmed and a gradual increase in lattice parameter with increasing x was observed. Fine grains with dense microstructure were revealed from the SEM images, while an obvious increase in grain size was detected when x = 0.5%. An optimized doping amount of 0.3% was determined, showing high dielectric constant (epsilon(r) approximate to 2190), low dielectric loss (tan approximate to 2.78 x 10(-3)), enhanced breakdown strength (290 kV/cm), and high-energy storage density (1.69 J/cm(3)) at room temperature. A possible mechanism, namely defect dipoles formation mechanism, was employed to explain the optimization of energy storage performance, and further confirmed from the variation in AC conductivity.
Colossal Dielectric Permittivity in (al+nb) Co-Doped Ba0.4Sr0.6TiO3 Ceramics

Bing Liu,Yu Hui Huang,Cheng Chao Hu,Kai Xin Song,Yong Jun Wu

DOI: https://doi.org/10.1016/j.ceramint.2019.04.135

IF: 5.532

2019-01-01

Ceramics International

Abstract:Stimulated by the outstanding colossal permittivity behavior achieved in trivalent and pentavalent cations co-doped rutile TiO2 ceramics, the co-doping effects on the dielectric behavior of Ba0.4Sr0.6TiO3 ceramics were further explored. In this work, (Al + Nb) co-doped Ba0.4Sr0.6TiO3 ceramics were synthesized via a standard solid state ceramic route. The structural evolution was analyzed using X-ray diffraction patterns and Raman spectra. Dense microstructures with no apparent change of grain morphology were observed from the scanning electron microscopy. A huge enhancement of dielectric permittivity was obtained with 1 mol% (Al + Nb) doping and excellent dielectric performances (epsilon(r) similar to 20,000, tan delta similar to 0.06 at 1 kHz) were achieved after further heat treatment. The formation of electron pinned defect dipoles localized in grains may account for the optimization of dielectric behaviors and the corresponding chemical valence states were confirmed from the XPS results.
Aging effects on dielectric properties of barium neodymium titanium tantalate ceramics

X. H. Zheng,X. M. Chen,T. Wang

DOI: https://doi.org/10.1007/s10854-006-8241-1

2006-01-01

Abstract:The aging effects on crystal structures and dielectric properties were investigated in Ba p Nd 6−p Ti 8−p Ta 2+p O 30 (p = 3, 4 and 5) ceramics with tungsten bronze structure. From XRD analyses on fresh and aged specimens, the slight change of crystal constant was concluded in Ba p Nd 6−p Ti 8−p Ta 2+p O 30 ceramics. Strong aging effects on the dielectric properties were observed in the present ceramics. After aging, a slightly decreased dielectric constant was observed combined with a significantly reduced dielectric loss in all the three compositions. These results had been discussed in term of the disorder-order state of ions at A- and B-sites. From tolerance factor and electronegativity difference, the stability was discussed for the filled type tungsten bronze phase.
Significant enhancement of energy storage properties of BaTiO3-based ceramics by hybrid-doping

Wenfeng Liu,Jinghan Gao,Yi Zhao,Shengtao Li

DOI: https://doi.org/10.1016/j.jallcom.2020.155938

IF: 6.2

2020-11-01

Journal of Alloys and Compounds

Abstract:In the present study, we designed a new system, Ba(Ti0.99-1.25xMn0.01Nbx)O3 (x = 0.5%, 1.0%, 1.25%, 1.5%), to improve the energy storage properties of BaTiO3–based ceramics. Here the acceptor dopant Mn was introduced to enhance the maximum polarization Pmax while reducing the remnant polarization Pr by inducing aging phenomena. The donor dopant Nb was added to make the hysteresis loop slimmer and slender through 'softening' effect. And the ratio of acceptor and donor was adjusted to modify the energy storage properties by modulating the shape of hysteresis loop. Results showed that an enhancement of 76% over pure BaTiO3 in recoverable energy storage density (Wrec) has been achieved in hybrid-doped samples, accompanied by a high energy conversion efficiency (η) up to 86%. Hereinto, donor-dominant samples doped with 1% Mn and 1.25% Nb exhibited the highest Wrec and η with excellent thermal stability. This study proved the feasibility of enhancing the energy storage properties by hybrid doping and may provide a new viewpoint for later studies.

materials science, multidisciplinary,chemistry, physical,metallurgy & metallurgical engineering
Significantly Enhanced Reliability in Defect-Engineered BaTi1-xMgxO3 Ceramics

Yetong Lv,Pengfei Wang,Yexia Qin,Jianwei Zhao,Jun Yang,Zhenxiao Fu,Xiuhua Cao,Lei Zhang,Shuhui Yu,Rong Sun

DOI: https://doi.org/10.1016/j.ceramint.2024.07.089

IF: 5.532

2024-01-01

Ceramics International

Abstract:BaTiO3-based ceramic is considered to be a fascinating dielectric material with high reliability for ultra-thin multilayer ceramic capacitors (MLCC). Here, we fabricated a series of acceptor-doped BaTiO3 (Mg: 0.2, 0.5, 1.0, 1.5, 2.0, and 5.0 mol%) ceramics with Al2O3 and SiO2 as sintering additives. With an increase in Mg concentration, the insulation resistance of the BaTi1-xMgxO3 ceramics initially increases and then decreases, in which the 0.5 mol% Mg-doped ceramic achieves superior degradation behavior. The reason is that with the incorporation of the acceptor ion Mg2+, the charge compensation mechanism in the system changes. Initially, barium vacancy is generated, which is gradually dominated by oxygen vacancy. Analysis indicates that the segregation of the acceptor state barium vacancy to the grain boundary increases the schottky barrier of the grain boundary, while the gradual increase of the donor state oxygen vacancy reduces the reliability of the ceramic. This study provides a comprehensive overview illustrating the significant role of point defects in the potential barrier of the grain boundary in acceptor-doped BaTiO3 ceramics. It identifies a pathway to achieve high reliability in BaTiO3based MLCC.
Effect of Dopants on Ageing Properties for the Pmn-0.1 Pt Relaxor Ferroelectric Ceramics

Yu Wang,Zhilun Gui,Y. C. Chan,Longtu Li,Xiaowen Zhang

DOI: https://doi.org/10.1007/bf00225636

1996-01-01

Journal of Materials Science Materials in Electronics

Abstract:Isothermal ageing properties of the typical ferroelectric relaxor system Pb(Mg1/3Nb2/3)O3-PbTiO3 (abbreviated as PMN-0.1 PT) doped with different kinds of oxides were measured and the effect of dopants on ageing inducing was investigated. The metallic ions of additives were considered to enter sites A or B in the perovskite structure with similar radii and their roles were distinguished as donors, acceptors or equivalent substitutors due to their valences. For the additions of acceptors, dielectric ageing is evident while no obvious ageing was found in the non-doped equivalently substituted or donor-doped PMN-0.1 PT systems.
Influence of Bi2O3 and Fe2O3 Doped on BaTiO3 Ceramics Microstructure

Shixi Zhao,Hanxing LIU

DOI: https://doi.org/10.3321/j.issn:1671-4431.2001.04.001

2001-01-01

Abstract:The effect of donor (Bi3+) and acceptor(Fe3+) on the grain growth and grain boundary of BaTiO3 were studied by SEM, TEM and EDAX. The results showed that donor inhibited grains growth, while the acceptor enhanced that; acceptor (Fe3+) doped led to the emergence of shell-core and grain-enclosed structure in the part of grains; the results of EDAX showed that the formation of shell-core and grain-enclosed structure were related to the segregation of Fe3+; the dislocation net was observed in Bi-doped barium titanate ceramic.
Microscopic origin of the enhanced piezoelectric thermal stability in acceptor doped lead-free Ba(Ti0.8Zr0.2)O3-50(Ba0.7Ca0.3)TiO3 ceramic

Mengye Yin,Minxia Fang,Lixue Zhang,Chao Zhou,Andong Xiao,Yuanchao Ji,Tianyu Ma,Xiaobing Ren

DOI: https://doi.org/10.1016/j.ceramint.2021.11.069

IF: 5.532

2022-02-01

Ceramics International

Abstract:Acceptor doping is effective in enhancing thermal stability in piezoceramics, while the reason underlying is still unclear and awaits explanation. In this work, through doping acceptor Mn in lead-free Ba(Ti0.8Zr0.2)O3-50(Ba0.7Ca0.3)TiO3 ceramic, our results show that doping Mn achieves higher depolarization temperature, even higher than Curie temperature (T C) and simultaneously a better piezoelectric thermal stability. Through microscopic and macroscopic analysis, the enhancement can be explained by the clamping effect induced by acceptor doping, which is carefully demonstrated by symmetry-conforming short-range ordering tendency theory. Thus, this work reveals the mechanism for enhanced depolarization temperature and piezoelectric thermal stability due to acceptor doping and will help developing new thermal stable lead-free piezoceramics applicable in a wider temperature range.

materials science, ceramics
The Relationship between PTCR Effect and Donor Content in Yb-Doped BaTiO3 Ceramics

Jian Quan Qi,Long Tu Li,Yong Li Wang,Qing Zhu,Zhi Lun Gui

DOI: https://doi.org/10.4028/www.scientific.net/KEM.224-226.67

2002-01-01

Key Engineering Materials

Abstract:Trivalent rare earth can occupy either Ba site or Ti site depending on its size and Ba/Ti ratio. Sintered in the air, semiconducting BaTiO3 ceramics doped by Yb2O3 could not be obtained in previous report. However, it could be obtained in case of the BaTiO3 as starting raw materials in this study. The sample with the minimum resistivity of about 35Omega.cm could be obtained when the content of Yb2O3 reached around 0.3mol%. The relationship between PTCR effect and donor content was also studied. In the case of other impurities free, the resistance jumping of the BaTiO3 ceramics decreases with the donor doping level increasing. Thus, the piling up of excess donors at grain boundary cannot enhance the PTCR effect.
Acceptor doping and actuation mechanisms in Sr-doped BiFeO3BaTiO3 ceramics

Ziqi Yang,Yizhe Li,Bing Wang,Juncheng Pan,Annette K. Kleppe,David A. Hall

DOI: https://doi.org/10.1016/j.jmat.2023.04.007

IF: 8.589

2023-05-01

Journal of Materiomics

Abstract:BiFeO3 BaTiO3 (BF-BT) ceramics are important multiferroic materials, which are attracting significant attention for potential applications in high temperature lead-free piezoelectric transducers. In the present study, the effects of Sr2+ as an acceptor dopant for Bi3+, in the range from 0 to 1.0%(in mole), on the structure and ferroelectric/piezoelectric properties of 0.7BiFeO3-0.3BaTiO3 ceramics were evaluated. The use of a post-sintering Ar annealing process was found to be an effective approach to reduce electrical conductivity induced by the presence of electron holes associated with reoxidation during cooling. A low Sr dopant concentration (0.3%, in mole) yielded enhanced ferroelectric (P max ∼ 0.37 C/m2, P r ∼ 0.30 C/m2) and piezoelectric (d 33 ∼ 178 pC/N, k p ∼ 0.27) properties, whereas higher levels led to chemically heterogeneous core-shell structures and secondary phases with an associated decline in performance. The electric field-induced strain of the Sr-doped BF-BT ceramics was investigated using a combination of digital image correlation macroscopic strain measurements and in-situ synchrotron X-ray diffraction. Quantification of the intrinsic (lattice strain) and extrinsic (domain switching) contributions to the electric field induced strain indicated that the intrinsic contribution dominated during the poling process.

materials science, multidisciplinary,chemistry, physical,physics, applied
The effect of acceptor dopant on the memory effect of BaTiO3 ceramics

Wenfeng Liu,Yihang Jin,Yi Zhao,Fanyi Kong,Jinghan Gao,Lei Zhang,Shengtao Li

DOI: https://doi.org/10.1016/j.jallcom.2022.167182

IF: 6.2

2022-12-20

Journal of Alloys and Compounds

Abstract:In the present study, BaTi(1-x)MxO3 (x = 0.005, 0.01, 0.015; M is Mn, Fe, and Co) ceramics were prepared by the conventional solid-state reaction method. Four distinct and independently addressed memory states were experimentally obtained based on the double hysteresis loop, which was achieved by acceptor doping in BaTiO3 ceramics. Moreover, this study indicated that for acceptor-doped BaTiO3 ceramics, larger electronegativity and smaller ionic radius of acceptor ions benefitted the more significant memory effect and better fatigue resistance. All these results could provide a promising solution for multi-state memory applications.

materials science, multidisciplinary,chemistry, physical,metallurgy & metallurgical engineering
Diffusion and Defect Chemistry of Temperature-Stable BaTiO3-based Ceramics: Experiment and Theoretical Calculations

Xu Cheng,Yichao Zhen,Mengjian Xiao,Peiyao Zhao,Kezhen Hui,Weichen Zhang,Ying Jiang,Limin Guo,Zhenxiao Fu,Xiuhua Cao,Hong Wang,Xiaohui Wang

DOI: https://doi.org/10.1016/j.jeurceramsoc.2024.116825

IF: 5.7

2025-01-01

Journal of the European Ceramic Society

Abstract:The ion diffusion and defect chemistry are the key factors in constructing the core-shell structure and improving the dielectric properties in temperature-stable BaTiO3-based dielectric ceramics. In this work, the BaTiO3-based ceramics doped with various rare-earth (RE) elements are prepared via the chemical coating method. The metal vacancy assisted A-B jumping migration path is confirmed as the main migration mechanism, where larger RE ions migrate faster and facilitate grain growth. About ~1mol % of amphoteric rare-earth ions are necessary to trap the oxygen vacancies and increase the activation energy and depolarized temperature. The electron paramagnetic resonance and thermodynamic model reveals that Mn4+ is not detected in all samples and the content of Mn2+ is determined by the Fermi level of the systems, influenced by the donor/acceptor doping, concentrations, and oxygen partial pressure. This work provides support for the rational design of dielectric materials with excellent dielectric performance and good reliability.
The Ageing and De-Ageing Behaviour of (ba0.85ca0.15)(ti0.9zr0.1)o3 Lead-Free Piezoelectric Ceramics

Yichi Zhang,Julia Glaum,Matthias C. Ehmke,Keith J. Bowman,John E. Blendell,Mark J. Hoffman

DOI: https://doi.org/10.1063/1.4931892

IF: 2.877

2015-01-01

Journal of Applied Physics

Abstract:Ageing behaviour usually occurs in acceptor-doped piezoelectric materials (e.g., hard lead zirconate titanate) and exhibits the development of a pinched or shifted hysteresis loop over time. Although no pinched hysteresis loop was observed for lead-free (Ba0.85Ca0.15)(Ti0.9Zr0.1)O3 material, this study showed that the piezoelectric properties change over time in the poled state. The shift of the hysteresis loop along the electric field axis and the development of asymmetry in strain and permittivity hysteresis loop were observed during the ageing process. The origin of this ageing behaviour is proposed to be local defect dipoles and the migration of the charged defects to the grain boundaries. The reorientation of the defect dipole contributes to a fast but unstable ageing mechanism in this material while the migration of the charged defects contributes to a slow but more stable mechanism.
Stabilized piezoelectricity upon ferro-ferro phase transition achieved by aging induced domain memory effect in acceptor doped lead-free ceramics

Mengye Yin,Minxia Fang,Yuanchao Ji,Dong Wang,Xiaobing Ren

DOI: https://doi.org/10.1016/j.scriptamat.2022.114872

IF: 6.302

2022-06-18

Scripta Materialia

Abstract:Strong temperature dependence of piezoelectricity ( d 33 ) attributed to morphotropic/polymorphic transition at room temperature limits the practical application of high performance lead-free piezoceramics. This work found aging induced domain memory effect is effective stabilizing d 33 through ferroelectric orthorhombic (O)-tetragonal (T) transition together with a large room temperature d 33 ( d ) in Mn doped lead-free 55Ba(Ti 0.8 Zr 0.2 )O 3 -45(Ba 0.7 Ca 0.3 )TiO 3 piezoceramics: 23.2% d 33 variation through O-T transition and a large d ∼ 323 pC/N for doped one when compared with those of undoped one (96.8% d 33 variation and d ∼ 278 pC/N). Restoring force induced by defect dipoles according to the symmetry conforming short-range ordering principle has been demonstrated with internal bias field and double hysteresis loops, while the outcoming domain memory effect, responsible for the stabilized behaviors, has been revealed with transmission electron microscopy observation and phase-field simulation. Thus, aging induced domain memory effect is effective achieving stabilized behaviors and large d simultaneously.

materials science, multidisciplinary,nanoscience & nanotechnology,metallurgy & metallurgical engineering

Mechanism of Aging Effect in Hybrid-Doped Batio3 Ceramics: Electronegativity and Ionic Radius

Kinetics Controlled Aging Effect of Ferroelectricity in Al-Doped and Ga-Doped Batio3

External Field Effects on Aging Phenomenon of Acceptor-Doped BaTiO3 Ceramics

Nonmonotonic Variation of Aging Behavior in Fe-doped BaTiO3 Ceramics

Influence of Bao-Cao-Sio2 on Dielectric Properties and Reliability of Batio3-Based Ceramics

Enhanced dielectric and ferroelectric properties of the hybrid-doped BaTiO3 ceramics by the semi-solution method

Study of the Defect Chemistry of Ca-Doped Batio3 Ceramics

Defect Dipoles Induced High‐energy Storage Density in Mn‐doped BST Ceramics Prepared by Spark Plasma Sintering

Colossal Dielectric Permittivity in (al+nb) Co-Doped Ba0.4Sr0.6TiO3 Ceramics

Aging effects on dielectric properties of barium neodymium titanium tantalate ceramics

Significant enhancement of energy storage properties of BaTiO3-based ceramics by hybrid-doping

Significantly Enhanced Reliability in Defect-Engineered BaTi1-xMgxO3 Ceramics

Effect of Dopants on Ageing Properties for the Pmn-0.1 Pt Relaxor Ferroelectric Ceramics

Influence of Bi2O3 and Fe2O3 Doped on BaTiO3 Ceramics Microstructure

Microscopic origin of the enhanced piezoelectric thermal stability in acceptor doped lead-free Ba(Ti0.8Zr0.2)O3-50(Ba0.7Ca0.3)TiO3 ceramic

The Relationship between PTCR Effect and Donor Content in Yb-Doped BaTiO<sub>3</sub> Ceramics

Acceptor doping and actuation mechanisms in Sr-doped BiFeO3BaTiO3 ceramics

The effect of acceptor dopant on the memory effect of BaTiO3 ceramics

Diffusion and Defect Chemistry of Temperature-Stable BaTiO3-based Ceramics: Experiment and Theoretical Calculations

The Ageing and De-Ageing Behaviour of (ba0.85ca0.15)(ti0.9zr0.1)o3 Lead-Free Piezoelectric Ceramics

Stabilized piezoelectricity upon ferro-ferro phase transition achieved by aging induced domain memory effect in acceptor doped lead-free ceramics