Design and Simulation of a High Intensity Heavy Ion RFQ Accelerator Injector
Wei Ma,Yuan He,Chenxing Li,Liang Lu,Liting Shi,Liepeng Sun,X. W. Xu,Zhouli Zhang,Hongwei Zhao
DOI: https://doi.org/10.18429/jacow-linac2016-thplr064
2017-01-01
Abstract:An 81.25 MHz continuous wave (CW) radio frequency quadrupole (RFQ) accelerator has been developed for Low Energy Accelerator Facility (LEAF) at the Institute of Modern Physics (IMP), the Chinese Academy of Science (CAS). In the CW operating mode, the proposed RFQ design adopted the conventional four-vane structure. The main design goals are providing the high shunt impendence with low power losses. In the electromagnetic (EM) design, the -mode stabilizing loops (PISLs) were optimized to produce a good mode separation. The tuners were also designed and optimized to tune frequency and field flatness of the operating mode. The vane undercuts were optimized to provide a flat field along the RFQ cavity. Additionally, a full length model with modulations was set up for the final EM simulations. In this paper, detailed EM design of the LEAF-RFQ will be presented and discussed. Meanwhile, structure error analysis is also studied. INTRODUCTION LEAF project was launched as a pre-research facility for high intensity Heavy Ion Accelerator Facility (HIAF) project [1, 2] at IMP. The LEAF will consist of a 2 mA U34+ electron cyclotron resonance ion source, a low energy beam transport line [3], a CW 81.25MHz RFQ accelerator, a medium energy beam transport and an experimental platform for nuclear physics. The layout of the LEAF project is shown in Fig. 1. The LEAF-RFQ will be adopted and used in the HIAF project. Figure 1: Layout of LEAF project. The design goal is to design a compact type cavity with lower power loss and high operation stability. Considering that LEAF-RFQ will operate at CW mode, four-vane structure is a better choice than four-rod type [4], which is a more stable structure and has better water cooling. Dipole mode can be excited if the dipole frequency is very close to operating frequency. Therefore, a good frequency separation is always a basic task to diminish the dipole mode effect. There are several methods proposed fighting against the dipole effect, such as, the vane coupling ring [5], PISL [6] and dipole stabilizer rod [7]. PISL is a good choice because it is easy to be cooled. Meanwhile, tuners and undercuts [8] are also used for frequency tuning and field flatness. In this paper, we focus on EM design and report detailed RF simulations using CST Microwave Studio (MWS) [9]. All parts of the resonator such as PISLs, tuners, and undercuts have been taken into account. Additionally, a complete RFQ model with vane modulations has been built and simulated. PARAMETERS AND STRUCTURE According to the requirements of the LEAF project, parameters of LEAF-RFQ are summarized in Table 1. Table 1: LEAF-RFQ Main Parameters Parameters Value Particle charge state U34+ Operation CW/pulsed Vane type Four vane Frequency (MHz) 81.25 Input energy (keV/u) 14 Output energy (MeV/u) 0.5 Inter-vane voltage (kV) 70 Kilpatrick factor 1.55 Peak current (emA) 2 Transmission efficiency (%) 97.2 Length of vane (mm) 5946.92 Average radius of aperture (mm) 5.805 ELECTROMAGNETIC SIMULATIONS The LEAF-RFQ cross-section has been optimized with the CST MWS. As a result, the cross-section geometry is shown in Fig. 2. The cross-section profile is defined with nine independent variables. Their final optimized values are indicated in the Table 2. In all subsequent 3D simulations, these parameters of cross-section are fixed except H. ___________________________________________ * Work supported by NSFC of China under Grant No. 11427904. † email address: w_ma@impcas.ac.cn Proceedings of LINAC2016, East Lansing, MI, USA THPLR064 2 Proton and Ion Accelerators and Applications 2C RFQs ISBN 978-3-95450-169-4 999 Co py rig ht © 20 17 CC -B Y3. 0 an d by th er es pe ct iv ea ut ho rs Figure 2: Geometry of LEAF-RFQ cross-section. Table 2: Parameters of LEAF-RFQ Cross-Section parameter value parameter value R0 5.805 mm Ws 20 mm Rv 4.354 mm 5° 80° Rc 50 mm Lv 17 mm H 360.5 mm 10° In order to study the mode separation between the main quadrupole mode and neighboring dipole mode, the EM simulations of PISL period RFQ model were performed without modulations. As shown in Fig. 3, PISL period of model includes two pairs of PISLs and eight tuners. Figure 3: PISL period model of LEAF-RFQ. Table 3: Frequency Separation Comparison Parameters Without PISLs With PISLs Frequency (MHz) 81.233 81.173 Nearest dipole mode frequency (MHz) 78.765 86.739 Q-D separation (MHz) -2.468 5.566 After optimization, as shown in Fig. 3, the PISLs have 10 mm outer diameter and pass through 50 mm holes in the vanes. After simulations, the RF parameters are shown in Table 3. Without PISLs, the dipole mode frequency is 2.468 MHz lower than the operating frequency. However, the dipole mode frequency is 5.566 MHz higher than operating frequency with PISLs. For frequency and field distribution tuning, the RFQ will be equipped with a total of 48 slug tuners. Figure 4 is the sketch map of tuners, which have a diameter of 100 mm and are uniformly distributed along the beam direction. According to the linear fitting shown in Fig. 5, tuning sensitivity of tuners equals 15.21 kHz/mm. Figure 4: Sketch map of tuner. Figure 5: Tuning sensitivity for all tuners. Figure 6: Sketch map of undercuts. Table 4: Tuned Undercuts Parameters h_cut D_in D_out 180 mm 60° 143 mm 139 mm Figure 7: Normalized electric field amplitude distribution along inter-vane without undercut and with undercut. THPLR064 Proceedings of LINAC2016, East Lansing, MI, USA ISBN 978-3-95450-169-4 1000 Co py rig ht © 20 17 CC -B Y3. 0 an d by th er es pe ct iv ea ut ho rs 2 Proton and Ion Accelerators and Applications