Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

Synthesis and Properties of a New High-Temperature Liquid Crystalline Thermoplastic Elastomer Based on Mesogen-Jacketed Liquid Crystalline Polymer

Synthesis and Characterization of New Liquid Crystalline Thermoplastic Elastomers Containing Mesogen-Jacketed Liquid Crystalline Polymers

High-Performance Olefin Thermoplastic Elastomer Based on Dynamically Cross-Linking Crystalline Macromers and Elastic Backbones

Temperature-Dependent Triple Crystal Polymorphism of Poly(hexamethylene Terephthalate): Long-Range Ordered Mesophase Formation and Crystal Structure–Property Relationships

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

Aba Type Triblock Copolymer Based on Mesogen-Jacketed Liquid Crystalline Polymer: Design, Synthesis, and Potential As Thermoplastic Elastomer

One‐Step Synthesis of Lignin‐Based Triblock Copolymers As High‐Temperature and UV‐Blocking Thermoplastic Elastomers

A new class of poly(ether‐ block ‐amide)s based on semi‐aromatic polyamide: synthesis, characterization and structure–property relations

Tough and Excellent Heat-Resistant Semiaromatic Polyamide Elastomer Containing Hierarchical Bonds: Synthesis and Synergistic Molecular Design

Supersoft Norbornene‐Based Thermoplastic Elastomers with High Strength and Upper Service Temperature

A Novel Semiaromatic Polyamide Thermoplastic Elastomer with Excellent Heat Resistance and Mechanical Properties

Development and Properties of Novel Thermoplastic Elastomer Based on Poly (Phenylene Ether)

Strategy for improving high-temperature properties of polyisoprene vulcanizates by addition of polymorphic TBIR

Synthesis and phase behavior of a new 2-vinylbiphenyl-based mesogen-jacketed liquid crystalline polymer with a high glass transition temperature and low threshold molecular weight

Synthesis, order-to-disorder transition, microphase morphology and mechanical properties of BAB triblock copolymer elastomers with hard middle block and soft outer blocks

Recent Advances in Thermoplastic Elastomers from Living Polymerizations: Macromolecular Architectures and Supramolecular Chemistry

Synthesis and Characterization of Thermoplastic Polyether-imide Elastormer

Synthesis, Characterization and Non-Isothermal Crystallization Kinetics of a New Family of Poly (Ether-Block-Amide)s Based on Nylon 10T/10I

Morphology and Properties of Novel Thermoplastic Polyurethane Elastomer

Preparation and Characterization of High Melt Strength Thermoplastic Polyester Elastomer with Different Topological Structure Using a Two-Step Functional Group Reaction

Temperature-induced Evolution of Micro-structure and Chain Dynamics in Thermoplastic Polyurethane with Low Hard Segment Content as Studied by In Situ Synchrotron SAXS and Time-Domain NMR Experiments