Abstract:The ternary polymerization strategy of incorporating different donor and acceptor units forming terpolymers as photovoltaic materials has been proven advantageous in improving power conversion efficiencies (PCEs) of polymer solar cells (PSCs). Herein, a series of low band gap nonconjugated terpolymer acceptors based on two different fused-ring electron-deficient building blocks (IDIC16 and ITIC) with adjustable photoelectric properties were developed. As the third component, ITIC building blocks with a larger π-conjugation structure, shorter solubilizing side chains, and red-shifted absorption spectrum were incorporated into an IDIC16-based nonconjugated copolymer acceptor PF1-TS4, which built up the terpolymers with two conjugated building blocks linked by flexible thioalkyl chain-thiophene segments. With the increasing ITIC content, terpolymers show gradually broadened absorption spectra and slightly down-shifted lowest unoccupied molecular orbital levels. The active layer based on terpolymer PF1-TS4-60 with a 60% ITIC unit presents more balanced hole and electron mobilities, higher photoluminescence quenching efficiency, and improved morphology compared to those based on PF1-TS4. In all-polymer solar cells (all-PSCs), PF1-TS4-60, matched with a wide band gap polymer donor PM6, achieved a similar open-circuit voltage (Voc) of 0.99 V, a dramatically increased short-circuit current density (Jsc) of 15.30 mA cm–2, and fill factor (FF) of 61.4% compared to PF1-TS4 (Voc = 0.99 V, Jsc = 11.21 mA cm–2, and FF = 55.6%). As a result, the PF1-TS4-60-based all-PSCs achieved a PCE of 9.31%, which is ∼50% higher than the PF1-TS4-based ones (6.17%). The results demonstrate a promising approach to develop high-performance nonconjugated terpolymer acceptors for efficient all-PSCs by means of ternary polymerization using two different A–D–A-structured fused-ring electron-deficient building blocks.This article has not yet been cited by other publications.

High-photovoltage all-polymer solar cells based on a diketopyrrolopyrrole-isoindigo acceptor polymer

Thiophene-Fused Perylenediimide-Based Polymer Acceptors for High-Performance All-Polymer Solar Cells

High-Performance All-Polymer Solar Cells Achieved by Fused Perylenediimide-Based Conjugated Polymer Acceptors.

Novel polymer acceptors achieving 10.18% efficiency for all-polymer solar cells

Polymer acceptor based on naphthalene diimide and diethynylbenzo[1,2-b:4,5-b'] dithiophene units for efficient all-polymer solar cells

Rational Design of Perylenediimide-Based Polymer Acceptor for Efficient All-Polymer Solar Cells

Mapping Nonfullerene Acceptors with a Novel Wide Bandgap Polymer for High Performance Polymer Solar Cells

Dye-incorporated Polynaphthalenediimide Acceptor for Additive-free High-performance All-polymer Solar Cells.

Polymerized small molecule acceptor based on diketopyrrolopyrrole and IDIC double electron-withdrawing building block for all-polymer solar cells

All-polymer solar cells based on a novel narrow-bandgap polymer acceptor with power conversion efficiency over 10%

N‐type Conjugated Polymer Based on Dicyanodistyrylbenzene and Naphthalene Diimide Units for All‐Polymer Solar Cells

Highly Efficient and Stable All-Polymer Solar Cells Enabled by Near-Infrared Isomerized Polymer Acceptors

8.0% Efficient All-Polymer Solar Cells with High Photovoltage of 1.1 V and Internal Quantum Efficiency near Unity

Fused Perylene Diimide-Based Polymeric Acceptors for Efficient All-Polymer Solar Cells

All-Polymer Solar Cells with Perylenediimide Polymer Acceptors

Nonconjugated Terpolymer Acceptors with Two Different Fused-Ring Electron-Deficient Building Blocks for Efficient All-Polymer Solar Cells

Dithienoquinoxalineimide‐based Polymer Donor Enables All‐Polymer Solar Cells Over 19% Efficiency

10.13% Efficiency All‐Polymer Solar Cells Enabled by Improving the Optical Absorption of Polymer Acceptors

14.4% efficiency all-polymer solar cell with broad absorption and low energy loss enabled by a novel polymer acceptor

Molecular Optimization on Polymer Acceptor Enables Efficient All‐Polymer Solar Cell with High Open‐Circuit Voltage of 1.10 V

Novel High-Efficiency Polymer Acceptors Via Random Ternary Copolymerization Engineering Enables All-Polymer Solar Cells with Excellent Performance and Stability.