Abstract:One of the most important requirements for a metallic biomaterial is the mechanical biocompatibility, which means excellent mechanical properties—high strength and fatigue strength, but low elastic modulus, to be mechanically harmonized with hard tissues. In order to improve the mechanical and biocompatible performance of the Ti-25.5Nb-4.5Ta-8.0Zr wt% alloy, the influence of cold plastic deformation and solution treatment on its properties were investigated. The Ti-25.5Nb-4.5Ta-8.0Zr wt% alloy was fabricated by melting in a cold crucible furnace (in levitation) and then subjected to several treatment schemes, which include cold rolling and different solution treatments. Microstructural and mechanical characteristics of specimens in as-cast and thermo-mechanically processed condition were determined by SEM microscopy and tensile testing, for different structural states: initial as-cast/as-received, cold rolled and solution treated at different temperatures (800, 900, and 1000 °C) and durations (5, 10, 15, and 20 min), with water quenching. It was concluded that both cold rolling and solution treatment have important positive effects on structural and mechanical properties of the biomaterial, increasing mechanical strength and decreasing the elastic modulus. Samples in different structural states were also corrosion tested and the results provided important information on determining the optimal processing scheme to obtain a high-performance biomaterial. The final processing route chosen consists of a cold rolling deformation with a total deformation degree of 60%, followed by a solution heat treatment at 900 °C with maintenance duration of 5 min and water quenching. By applying this thermo-mechanical processing scheme, the Ti-25.5Nb-4.5Ta-8.0Zr wt% alloy showed an elastic modulus of 56 GPa (5% higher than in the as-cast state), an ultimate tensile strength of 1004 MPa (41.8% higher than in the as-cast state), a yield strength of 718 MPa (40.6% higher than in the as-cast state), and increased corrosion resistance (the corrosion rate decreased by 50% compared to the as-cast state).

Mechanical Properties, Structure, and Biocompatibility of Dual-Axially Forged Ti94fe3au3, Ti94fe3nb3, and Ti94au3nb3 Alloys

Electrochemical Behavior and Biocompatibility of Ti-Fe-Cu Alloy with High Strength and Ductility

Mechanical Properties and Biocompatibility of the Ti-Based Low-Alloys Minor Alloying by the Noble Metals

Microstructure evolution, hot deformation behavior and mechanical properties of Ti-43Al-6Nb-1B alloy

Two novel titanium alloys for medical applications: Thermo-mechanical treatment, mechanical properties, and fracture analysis

Preparation, structural, microstructural, mechanical, and cytotoxic characterization of Ti-15Nb alloy for biomedical applications

Effects of Multiaxial Forging on Microstructure and High Temperature Mechanical Properties of Powder Metallurgy Ti-45Al-7Nb-0.3W Alloy

Microstructure evolution and mechanical properties of a novel beta γ-TiAl alloy

Design, Development, and Characterization of a Novel Amorphous Ti-10Nb-10Zr-5Si-5Sn-5Cu Biomaterial Alloy

Microstructure Evolution and Deformation Mechanism of Α+β Dual-Phase Ti-xNb-yTa-2Zr Alloys with High Performance

Investigation of sliding wear, electrochemical corrosion, and biocompatibility of Ti-Nb alloys for biomedical applications

Microstructure and Mechanical Properties of Biomedical Ti-Zr-Nb-Ta-Sn High-Entropy Alloys

Elaboration of Ti-based Biocompatible Alloys Using Nb, Fe and Zr as Alloying Elements

Effects of Cold Rolling Deformation and Solution Treatment on Microstructural, Mechanical, and Corrosion Properties of a Biocompatible Ti-Nb-Ta-Zr Alloy

Biocompatible As-Cast and Homogenized TiNbTaZrMoV High Entropy Alloys: Mechanical Properties, Corrosion Resistance and in Vitro Studies

Mechanical properties and corrosion resistance characterization of a novel Co36Fe36Cr18Ni10 high-entropy alloy for bioimplants compared to 316L alloy

Assessing Microstructural, Biomechanical, and Biocompatible Properties of TiNb Alloys for Potential Use as Load-Bearing Implants

Microstructure and mechanical properties of biodegradable Zn-2Cu-0.1Ti alloy for orthopedic applications

Ti$_{1-x}$Au$_x$ Alloys: Hard Biocompatible Metals and Their Possible Applications

Corrosion and Biocompatibility Properties of TiZrNbCrV, TiZrNbFeCr, and TiZrNbFeV High Entropy Alloys Produced through Mechanical Alloying

Microstructure and Physico-Mechanical Properties of Biocompatible Titanium Alloy Ti-39Nb-7Zr after Rotary Forging