Abstract:The mechanical behavior of a commercially pure titanium (CP-Ti) is systematically investigated in quasi-static (Instron, servohydraulic) and dynamic (UCSD's recovery Hopkinson) compression. Strains over 40% are achieved in these tests over a temperature range of 77–1000K and strain rates of 10−3–8000/s. At the macroscopic level, the flow stress of CP-Ti, within the plastic deformation regime, is strongly dependent on the temperature and strain rate, and displays complex variations with strain, strain rate, and temperature. In particular, there is a three-stage deformation pattern at a temperature range from 296 to 800K, the specific range depending on the strain rate. In an effort to understand the underlying mechanisms, a number of interrupted tests involving temperature jumps are performed, and the resulting microstructures are characterized using an optical microscope. Based on the experimental results and simple estimates, it is concluded that the three-stage pattern of deformation at temperatures from 296 to 800K, is a result of dynamic strain aging, through the directional diffusion of dislocation-core point defects with the moving dislocation at high strain rates, although the usual dynamic strain aging by point defects segregating outside the dislocation core through volume diffusion is also observed at low strain rates and high temperatures. The microscopic analysis shows that there is substantial deformation twinning which cannot be neglected in modeling the plastic flow of CP-Ti. The density of twins increases markedly with increasing strain rate, strain, and decreasing temperature. Twin intersections occur, and become more pronounced at low temperatures or high strain rates. In sum, the true stress–true strain curves of CP-Ti show two stages of deformation pattern at low temperatures, three stages at temperatures above 296K, and only one stage at temperatures exceeding 800K, although all three stages may exist even at 1000K for very high strain rates, e.g. 8000/s. While the dislocation motion is still the main deformation mechanism for plastic flow, the experimental results suggest that dynamic strain aging should be taken into account, as well as the effect of deformation twinning.

Experimental Study on Pure Titanium Subjected to Different Combined Tension and Torsion Deformation Processes

Experimental Study on Pure Titanium During the Positive-Torsion and Positive-Negative-torsion

Characterization and Analysis of Strain Heterogeneity at Grain-Scale of Titanium Alloy with Tri-Modal Microstructure During Tensile Deformation

Influences of pre-torsion deformation on microstructure and mechanical properties of pure titanium subjected to subsequent tension deformation

Microstructure and microhardness evolution of Ti-10V-2Fe-3Al alloy under tensile/torsional deformation modes

Mechanical properties and deformation mechanisms of a commercially pure titanium

Research on Microstructure Deformation Mechanism of Crack Tip in Titanium under Tension along Different Orientations

Experimental Study on Microstructure and Hardness of Pure Titanium Subjected to Torsion Deformation at Different Temperatures

Hardening and Softening Analysis of Pure Titanium Based on the Dislocation Density During Torsion Deformation

Microstructural evolution, mechanical properties and fracture toughness of near β titanium alloy during different solution plus aging heat treatments

Ductile-to-brittle Fracture of CP Titanium with Torsion Deformation

Experimental Study for the Influence of Twinning on the Plastic Deformation of Pure Polycrystalline Titanium

Fracture Behaviors of Commercially Pure Titanium under Biaxial Tension: Experiment and Modeling

Microstructure and Microtexture Evolution of Pure Titanium During Single Direction Torsion and Alternating Cyclic Torsion

A Comparative Study on the Microstructure and Mechanical Behavior of Titanium: Ultrafine Grain Vs. Coarse Grain

Microscopic Mechanisms Underlying the Dynamic Tensile Behaviors of a Commercially Pure Titanium at Elevated Temperatures

Influence of Deformation Stress Triaxiality on Microstructure and Microhardness of Pure Copper Processed by Simultaneous Torsion and Tension

Fracture Mechanism of Electrically-Assisted Micro-Tension in Nanostructured Titanium Using Synchrotron Radiation X-Ray Tomography

Effect of Loading Type on Deformation and Fracture Behavior of Ti-55531 Alloy with Bimodal Microstructure

Effects of Β Treatments on Microstructures and Mechanical Properties of TC4-DT Titanium Alloy

Deformation and Fracture Mechanisms of Ti-55531 Alloy with a Bimodal Microstructure under the Pre-Tension Plus Torsion Composite Loading