Abstract:To investigate how laser peen texturing (LPT) parameters affect the patterns formed on the surface of E690 high-strength steel, and how these patterns subsequently influence tribological properties, the LPT process, including multiple shocks, was simulated by ABAQUS and verified by experiments. The residual stress and microstructure on the surface of micro-dimples after LPT were measured and observed by X-ray stress analyzer and transmission electron microscope. The tribological properties of specimens with different LPT density and depth were tested by reciprocating friction experiments, and the worn surfaces were observed using a scanning electron microscope. The experimentally obtained plastic deformation depths of the micro-dimples were − 8.82 μm, −18.31 μm, −28.72 μm and − 36.34 μm when the shock number was varied from 1 to 4. The simulation and experiment results were within 3.3 %, verifying the accuracy and reliability of the simulation. When the shock number was ≥ 2, the residual stress values in all directions at the test points within the micro-dimples tended to be consistent, and the full width at half maximum (FWHM) values gradually increased with increasing shock number. The TEM images and electron diffraction pattern of the specimen after three shocks showed that nanocrystals are formed on the bottom surface of the micro-dimple. In the friction experiments, the average friction coefficient first decreased and then increased with increasing LPT density. The average friction coefficient was the lowest when the LPT density was 20 %, for a constant micro-dimple depth. When the LPT density was 20 %, increasing the micro-dimple depth had little effect on the average friction coefficient, but the stability time of the specimens increased substantially. The wear surface of the untextured specimen showed deep and wide wear marks, and serious abrasive wear and adhesive wear occurred. Suggested LPT parameters for optimum wear resistance are an LPT density of 20% and shock number of 3.

Influence of Heat Affected Zone on Tribological Properties of CuSn6 Bronze Laser Dimple Textured Surface

Comparisons of Tribological Properties Between Laser and Drilled Dimple Textured Surfaces of Medium Carbon Steel

Improving Tribological Behavior of Laser Textured Ti-20Zr-10Nb-4Ta Alloy with Dimple Surface

Manipulation Tribological Behavior of Ti6Al4V Alloy Via a Duplex Treatment of Double Glow Plasma Surface Molybdenizing-Laser Surface Texturing (LST)

Tribological Properties of Ti6Al4V Titanium Textured Surfaces Created by Laser: Effect of Dimple Density

Dendritic solidification of undercooled CU-20%Pb hypomonotectic alloy

Effects of Texture Density on Tribological Performance of Laser Peen Textured Surface

The Friction And Wear Behavior Of Laser Textured Surfaces In Non-Conformal Contact Under Starved Lubrication

Tribological Properties of Dimple-Textured Titanium Alloys under Dry Sliding Contact

Surface Texturing for Low Friction Mechanical Components

Effects of Texture Geometry on the Tribological Performance of Brass with a TiN Coating under Lubricated Rotation

Experimental study on laser peen texturing and tribological properties of E690 high-strength steel

Friction and Wear Performance of Laser Peen Textured Surface under Starved Lubrication

Effect of Micro-Dimple Texture on the Tribological Performance of Brass with Titanium Nitride (TiN) Coating under Oil-Lubricated Conditions

Combined Effect of a Laser Cladded Coating and Surface Texture on Tribological Performance Under Dry Sliding and Starved Lubrication

Surface Textures Fabricated by Laser Surface Texturing and Diamond Cutting - Influence of Texture Depth on Friction and Wear

Tribological Behavior of Femtosecond Laser-Textured Leaded Brass

Tribological Properties of Micro-Textured Surfaces of ZTA Ceramic Nanocomposites under the Combined Effect of Test Conditions and Environments

Friction and Wear Behavior Analysis of the Stainless Steel Surface Fabricated by Laser Texturing Underwater

Laser Surface Texturing under Transformer Oil Conditions for Improved Process Quality and Tribological Behaviors

Improving Tribological Performance of Mechanical Components by Laser Surface Texturing