Abstract:Organometal halide perovskite is one of the most promising materials for high efficient thin-film solar cell. Solution fabrication process shows that the recorded power conversion efficiency (PCE) is 23.7%, however, large scale fabrication suffers the inevitable toxic solvent, preventing it from implementing the green commercialization. As one of the matured large-scale fabrication techniques, the vapor deposition is recently found to promise the green fabrication of perovskite thin film without toxic solvent. However, the PCE based on vapor deposition is considerably lower than that based on solution fabrication because of ineffective regulation methods of the perovskite films. So, there is intensive requirement for optimizing the growth of perovskite in vapor deposition for improving PCE, especially, developing a kind of quality regulation method of the perovskite films. In this study, we provide a method of adjusting grain size in vapor deposition method. The grain size optimization of MAPbI 3 films is realized by simply modulating the reaction temperature between PbI 2 films and MAI vapor. We set the reaction temperature to be 140 °C, 160 °C, 180 °C and 200 °C separately and establish the relationship between reaction time and grain size during the complete conversion of PbI 2 film into MAPbI 3 film. We find that the average grain size of the film increases first with growth temperature increasing from 140 °C to 180 °C and then decrease at 200 °C, giving an average grain size of 0.81 \begin{document}${\text{μm}}$\end{document} and a largest grain size of about 2 \begin{document}${\text{μm}}$\end{document} at 180 °C. The defect density of perovskite film is deduced from the space charge limited current model, showing that it decreases from 5.90 × 10 16 cm –3 at 140 °C to 2.66 × 10 16 cm –3 at 180 °C. Photovoltaic devices with structure FTO/TiO 2 /C 60 /MAPbI 3 /spiro-OMeTAD/Au are fabricated to demonstrate the performance. It is found that the devices with an active area of 0.045 cm 2 show that with the increase of grain size, the average PCE increases from 14.00% to 17.42%, and the best device shows that its PCE is 17.80% with 4.04% hysteresis index. To show the possibility of scaling up, we fabricate a uniform perovskite thin film with an area of about 72 cm 2 , and a device with an active area of 1 cm 2 , which gives a PCE of 13.17% in reverse scan. In summary, our research provides a method of regulating the grain size for the vapor deposition, which can improve device performance by reducing the trap density in perovskite film for suppressing the carrier recombination in grain boundary. Meanwhile, we prepare high performance devices and large area thin films, showing their potential in large area device fabrication and applications.

Efficient planar heterojunction perovskite solar cells with weak hysteresis fabricated via bar coating

A Polymerization‐Assisted Grain Growth Strategy for Efficient and Stable Perovskite Solar Cells

Tailored Key Parameters of Perovskite for High-Performance Photovoltaics

High-Performance Perovskite Solar Cells Fabricated by a Hybrid Physical–Chemical Vapor Deposition

Vapor-assisted deposition of CsPbIBr2 films for highly efficient and stable carbon-based planar perovskite solar cells with superior Voc

High-performance Planar Heterojunction Perovskite Solar Cells: Preserving Long Charge Carrier Diffusion Lengths and Interfacial Engineering

High-Performance Simple-Structured Planar Heterojunction Perovskite Solar Cells Achieved by Precursor Optimization.

Stable and Efficient 3D-2D Perovskite-Perovskite Planar Heterojunction Solar Cell without Organic Hole Transport Layer

Optimization of grain size to achieve high-performance perovskite solar cells in vapor deposition

Suppressing halide phase segregation in wide-bandgap perovskite film by co-doping strategy for high-performance and stable perovskite solar cells

Efficient perovskite solar mini-modules fabricated via bar-coating using 2-methoxyethanol-based formamidinium lead tri-iodide precursor solution

Dimensionality Control of SnO2 Films for Hysteresis-Free, All-Inorganic CsPbBr3 Perovskite Solar Cells with Efficiency Exceeding 10

Surface-Orientation Elimination of Vapor-Deposited PbI 2 Flakes for Efficient Perovskite Synthesis on Curved Solar Cells

Air-processed MAPbI3 perovskite solar cells achieve 20.87% efficiency and excellent bending resistance enabled via polymer dual-passivation strategy

Crystallization Kinetics Engineering toward High-Performance and Stable CsPbBr 3 -Based Perovskite Solar Cells

Enhancing the Efficiency of Low-Temperature Planar Perovskite Solar Cells by Modifying the Interface Between Perovskite and Hole Transport Layer with Polymers

Low-temperature solution-processed perovskite solar cells with high efficiency and flexibility.

High performance and stability of perovskite solar cells achieved through anti-solvent modulation of multi-orientation PbI 2 and stress relief

Fabrication of highly efficient and ambient stable planar MAPbI3 perovskite solar cells via defect passivation through crosslinking strategy

Phase transition induced recrystallization and low surface potential barrier leading to 10.91%-efficient CsPbBr3 perovskite solar cells

CH 3 NH 3 PbBr 3– x I x Quantum Dots Enhance Bulk Crystallization and Interface Charge Transfer for Efficient and Stable Perovskite Solar Cells