Abstract:Logging tools play a crucial role in detecting underground oil and gas resources, operating in demanding hightemperature downhole environments.Previous studies have successfully employed several passive thermal management systems (PTMSs) to safeguard downhole electronics during operation [1][2][3][4][5].This system comprises vacuum flasks, thermal insulators, phase change materials (PCMs), electronics, and skeletons.Among these components, a combination of vacuum flasks and insulators has been used to minimize heat transfer from high-temperature environments.PCMs positioned between the skeleton and insulators absorb heat generated by electronics, enabling the logging tool to operate safely for extended periods in high-temperature wells.Despite these advancements, the thermal performance in the PTMS can be further improved, with shorter system length to mitigate downhole operation risks.Consequently, there is a need to propose a PTMS that not only enhances heat transfer but also significantly reduces its overall length.This paper introduces a PTMS designed for logging tools, aiming to enhance heat transfer and minimize length through thermal-structural co-optimization.The parametric geometry model of the logging tool was developed using Solidworks, and COMSOL was employed to simulate the thermal performance of the system.The Nelder-Mead algorithm was chosen for optimizing the logging tool, with the length of insulators and PCMs as the variables.The optimization objective was to minimize the overall length, with the constraint that the electronics' temperature should not exceed 125°C.Constraints were addressed using the external penalty function method, and a maximum of 200 optimization iterations was set.The external ambient temperature, total power consumption of the heat source, and operating time were 205°C, 25 W, and 9 hours, respectively.The optimal logging tool design was achieved through algorithmic iterations.The initial total length of the logging tool was 4676 mm, with the initial maximum temperature of heat sources at 114.13°C.With increasing iterations, the overall length of the logging tool showed a downward trend, stabilizing after approximately 80 iterations.Simultaneously, the maximum temperature of heat sources fluctuated around the constraint temperature of 125°C.After 135 iterations, the optimized length reduced to 3778.8 mm, and the maximum temperature of heat sources reached 124.99°C.Additionally, the overall homogeneity of the logging tool improved.The optimization resulted in an increase in the latent heat utilization of PCM from 60.2% to 96.3%, demonstrating that the proposed structure can reduce length while enhancing heat transfer.Thermal-structural co-optimization emerges as a crucial guideline for designing passive thermal management systems for logging tools, holding promising prospects in the petroleum industry.

Thermal Management Of Downhole Electronics Cooling In Oil & Gas Well Logging At High Temperature

Thermal Management of the High-power Electronics in High Temperature Downhole Environment

Thermal Optimization of High-Temperature Downhole Electronic Devices

Distributed thermal management system for downhole electronics at high temperature

Thermal Management for High-Power Downhole Electronics Using Liquid Cooling and PCM under High Temperature Environment

Passive thermal management system for downhole electronics in harsh thermal environments

A hybrid thermal management system combining liquid cooling and phase change material for downhole electronics

Thermal management systems for electronics using in deep downhole environment: A review

An Integrated Downhole Thermal Management System with Improved Operating Thermal Performance and Rapid Post-Operation Air Cooling

Thermal-Structural Co-Optimization of Passive Thermal Management System for Logging Tool

Thermal Optimization of a Logging Tool Used in High Temperature Downhole Environment

Experimental and Numerical Investigation of Low Melting Point Alloy for Downhole Electronics at High Temperature

The Resistivity Imaging LWD Method Suitable for Oil-Based Drilling Fluid

Experimental Study on Active Thermal Protection for Electronic Devices Used in Deep−Downhole−Environment Exploration

A Transient Thermal Model for Forecasting the Real-Time Temperature of Downhole Electronics

Strategies for Prevention of Downhole Tool Failure Caused by High Bottomhole Temperature in Geothermal and High-Pressure/High-Temperature Oil and Gas Wells

Downhole heat management for drilling shallow and ultra-deep high enthalpy geothermal wells

Durable and Reliable Thermal Management System with Superior Temperature Uniformity for Sidewall Coring Tool in Extreme Thermal Environments

An improved numerical model based on the equivalent thermal conductivity method for downhole thermal management systems

Simulation study of drilling fluid cooling in long horizontal wells based on phase change heat absorption

A numerical model coupling multiple heat transfer modes to develop a passive thermal management system for logging tool