Abstract:Dimethyl furan-2,5-dicarboxylate (DMFDCA) is a valuable biomass-derived chemical that is an ideal alternative to fossil-derived terephthalic acid as a monomer for polymers. The one-step oxidation of 5-hydroxymethylfurfural (HMF) to DMFDCA is of practical significance. It not only shortens the reaction pathway but also avoids the separation process of intermediates; thus, reducing cost. In this work, non-noble bimetallic catalysts supported on N-doped porous carbon (CoMn@NC) were synthesized via a one-step co-pyrolysis procedure using different pyrolysis temperatures and proportions of metal precursors and additives. We employed the prepared CoMn@NC catalysts in the aerobic oxidation of HMF under mild reaction conditions to obtain DMFDCA. High-yield DMFDCA was obtained by screening the prepared catalysts and optimizing the reaction conditions, including the strength and amount of the base, as well as the reaction temperature. The optimized yield of DMFDCA was 85% over the Co3Mn2@NC-800 catalyst after 12 h at 50 degrees C using ambient-pressure oxygen. The physicochemical properties of the catalysts were determined using a variety of characterization techniques, the factors affecting the performance of each catalyst were investigated, and the relationship between the physicochemical properties and performance of the prepared catalysts was elucidated. A porous structure with a high surface area had a positive effect on mass transfer efficiency. Cobalt nanoparticles (NPs) and atomically dispersed Mn were coordinated to N-doped carbon to form M-N-x (where M = Co or Mn). Based on the Mott-Schottky effect, there was significant electron transfer between each metal and the N-doped carbon, additionally, the metal NPs supplied electrons to the carbon atoms. The electron-deficient metal site in the pyridinic N-rich carbon was beneficial for the activation of HMF and oxygen. The activation of oxygen produced reactive oxygen species (such as superoxide radical anions) to ensure high selectivity to DMFDCAthrough dehydrogenative oxidation of the hemiacetal intermediate and hydroxymethyl group of 5-hydroxymethyl-2-methyl-furoate. The existence of disordered and defective carbons increased the number of active sites. Subsequently, we performed a series of control experiments. Based on our current experimental results and previous studies, we propose a simple mechanism for the aerobic oxidation of HMF to DMFDCA. The catalyst was stable, its performance decreased slightly after two cycles, and it was tolerant to SCN - ions and resistant against N or S poisoning. Furthermore, the use of this catalytic system can be expanded to various substituted aromatic alcohols, such as benzyl alcohols with different substituents, furfuryl alcohol, and heterocyclic alcohols. Simultaneously, the product type was further extended from methyl esters to ethyl esters with a high yield when the substrate reacted with ethanol. In conclusion, this catalytic system can be applied in the production of carboxylic esters for polymers.

Catalytic transfer hydrogenation/hydrogenolysis of 5-hydroxymethylfurfural to 2,5-dimethylfuran over Ni-Co/C catalyst

Formic Acid Enabled Selectivity Boosting in Transfer Hydrogenation of 5-Hydroxymethylfurfural to 2,5-Furandimethanol on Highly Dispersed Co–Nx Sites

Liquid-Phase Aerobic Oxidation of 5-Hydroxymethylfurfural to 2,5-Furandicarboxylic Acid over Co/Mn/Br Catalyst

Catalytic in-situ hydrogenation of 5-hydroxymethylfurfural to 2,5-dimethylfuran over Cu-based catalysts with methanol as a hydrogen donor

Production of 2,5-Furandicarboxylic Acid by Optimization of Oxidation of 5-Methyl Furfural over Homogeneous Co/Mn/Br Catalysts

Selective Hydrogenation of Furfural to Furfuryl Alcohol Without External Hydrogen over N-doped Carbon Confined Co Catalysts

Cu−Ni Bimetallic Hydroxide Catalyst for Efficient Electrochemical Conversion of 5‐hydroxymethylfurfural to 2,5‐furandicarboxylic Acid

CuZnCoOx Multifunctional Catalyst for in Situ Hydrogenation of 5-Hydroxymethylfurfural with Ethanol As Hydrogen Carrier

Efficient catalytic transfer hydrogenation of furfural to furfuryl alcohol in near-critical isopropanol over Cu/MgO-Al2O3 catalyst

Optimization and reaction kinetics of catalytic transfer hydrogenation of 5‐hydroxymethylfurfural to 2, 5‐dimethylfuran over CuCoOx catalysts

Selective hydrogenolysis of 5-hydroxymethylfurfural to 2,5-dimethylfuran with high yield over bimetallic Ru-Co/AC catalysts

Noble metal free carbon encapsulated CoNi alloy catalyst for total hydrogenation of 5‐hydroxymethylfurfural to tetrahydrofurandiol in aqueous media

Hydrogenolysis of 5-Hydroxymethylfurfural to 2,5-Dimethylfuran Over a Modified CoAl-Hydrotalcite Catalyst

Highly selective hydrogenation of 5-hydroxymethylfurfural to 2,5-dimethylfuran at low temperature over a Co–N–C/NiAl-MMO catalyst

Selective hydrodeoxygenation of 5-hydromethylfurfural to 2,5-dimethylfuran over PtFe/C catalyst

Insights into the route of 5-hydroxymethylfurfural hydrodeoxygenation to 2,5-dimethylfuran over N-doped carbon anchored CoMo bimetallic catalyst

The catalytic hydrogenation of furfural to 2-methylfuran over the Mg-Al oxides supported Co-Ni bimetallic catalysts

Aerobic Oxidation of 5-Hydroxymethylfurfural to Dimethyl Furan-2,5- Dicarboxylate over CoMn@NC Catalysts Using Atmospheric Oxygen

Nickel-tungsten carbide catalysts for the production of 2,5-dimethylfuran from biomass-derived molecules.

Nickel - Titania Supported Catalysts for Direct Selective Hydrodeoxygenation of 5-Hydroxymethylfurfural to 5-Methylfurfural

Selective Hydrodeoxygenation of 5‐Hydroxymethylfurfural to 2,5‐Dimethylfuran over Heterogeneous Iron Catalysts