Enhanced Oxidative and Adsorptive Capability Towards Antimony by Copper-Doping into Magnetite Magnetic Particles

Zenglu Qi,Huachun Lan,Tista Prasai Joshi,Ruiping Liu,Huijuan Liu,Jiuhui Qu

DOI: https://doi.org/10.1039/c6ra13412b

IF: 4.036

2016-01-01

RSC Advances

Abstract:Copper-doped magnetite improved particle size, enhanced adsorption capacity of antimony (Sb) and oxidation ability of Sb (III).

What problem does this paper attempt to address?

Enhanced mechanism of copper doping in magnetic biochar for peroxymonosulfate activation and sulfamethoxazole degradation

Chuanbin Wang,Haoxi Dai,Lan Liang,Ning Li,Xiaoqiang Cui,Beibei Yan,Guanyi Chen

DOI: https://doi.org/10.1016/j.jhazmat.2023.132002

IF: 13.6

2023-07-08

Journal of Hazardous Materials

Abstract:Magnetic biochar is excellent for separation and peroxymonosulfate (PMS) activation. Copper doping could improve the catalytic capability of magnetic biochar significantly. In this study, cow dung biochar is applied to investigate the effects of copper doping on the magnetic biochar, focusing on the specific influence on the consumption of active sites, the production of oxidative species and the toxicity of degradation intermediates. The results showed that copper doping promoted the uniform distribution of iron sites on the biochar surface and reduced iron aggregation. At the same time, copper doping interpreted the biochar with larger specific surface area, which was beneficial to the adsorption and degradation of sulfamethoxazole (SMX). The SMX degradation kinetic constant with copper-doped magnetic biochar was 0.0403 min −1 , which was 1.45 times than that of magnetic biochar. Besides, copper doping might accelerate the consumption of CO, Fe 0 , Fe 2+ sites and hinder the activation of PMS at copper-related sites. Furthermore, copper doping promoted the PMS activation by magnetic biochar through accelerated electron transfer . For the oxidative species, copper doping accelerated the production of hydroxyl radicals, singlet oxygen, and superoxide radicals in solution and inhibited the generation of sulfate radicals. In addition, SMX could be directly decomposed into less toxic intermediates in the copper-doped magnetic biochar/PMS system. In conclusion, this paper provides insight and analysis of the advantages of copper doping on the magnetic biochar, which helps to facilitate the design and practical application of bimetallic biochar.

environmental sciences,engineering, environmental
Synthesis of Ce(III)-doped Fe3O4 Magnetic Particles for Efficient Removal of Antimony from Aqueous Solution.

Zenglu Qi,Tista Prasai Joshi,Ruiping Liu,Huijuan Liu,Jiuhui Qu

DOI: https://doi.org/10.1016/j.jhazmat.2017.01.007

IF: 13.6

2017-01-01

Journal of Hazardous Materials

Abstract:Aqueous antimony (Sb) pollution from human activity is of great concern in drinking water due to its adverse health effect. Magnetic Fe3O4 particles, with high separation ability from solution, have been considered as a low-cost Sb adsorbent for contaminants. However, the limited adsorption capacity has restricted its practical application. In this study, a solvothermal approach was developed for doping Ce(III) into Fe3O4, thereby increasing the adsorption efficacy for both Sb(III) and Sb(V). In contrast to un-doped Fe3O4, the adsorption capacity towards Sb(III) and Sb(V) in Ce-doped materials increased from 111.4 to 224.2mg/g and from 37.2 to 188.1mg/g at neutral pH, respectively. Based on the combined results of XPS, XRD, and FTIR, it confirmed that Ce atom successfully doped into the Fe3O4 structure, resulting in the decreased particle size, increased the surface area, and isoelectric point. Furthermore, the vibrating sample magnetometer (VSM) results showed that the Ce doping process had some side effects on the primitive magnetic property, but remaining the high separation potential during water treatment. According to the high removal efficiency and magnetic property, the Ce-doped Fe3O4 of great simplicity should be a promising adsorbent for aqueous Sb removal.
Design of Magnetic Nanoparticles with High Magnetic Separation Efficiencies and Durability for Cu2+ Adsorption

Shenghua Wang,Yingying Yu,Le He,Dake Zhang,Miaomiao Ye

DOI: https://doi.org/10.1088/1361-6528/ab55c2

IF: 3.5

2019-01-01

Nanotechnology

Abstract:Fe3O4@SiO2 core-shell structured nanoparticles are promising candidates for adsorption of heavy metal ions from waste water due to their high adsorption capacities and feasible recycling process. However, their practical applications have been hindered by the trade-off between the magnetic separation efficiency and durability. In this study, we demonstrate the preparation of amino-functionalized Fe3O4@SiO2 absorbents with both high magnetic separation efficiencies and durability in strong acidic environment. Our key strategy was to use a thin but highly protective silica layer by manipulating the sol-gel chemistry. With the protection of a thin but poorly permeable silica shell, the durability of the Fe3O4 in strong acid solution was significantly enhanced while its magnetic separation efficiency was maintained. We also demonstrated the adsorption of Cu2+ from aqueous solution corresponded well with the pseudo-second-order kinetic model and the Langmuir adsorption isotherm. The adsorption capacity can be further improved by coating an additional layer of mesoporous SiO2 outside Fe3O4@SiO2. The design of highly durable magnetic absorbents without sacrificing the magnetic separation efficiency greatly facilitates the practical applications of magnetic nanoparticles in adsorption of heavy metal ions.
Enhanced adsorption-oxidation of Sb(III) over chitosan bimetallic beads: In-situ generated O2•– and autocatalytic effect of Sb(III)

Yaopeng Zhang,Miaojia Du,Chensi Shen,Ran Zhang,Chenye Xu,Chunyan Ma,Manhong Huang,Fang Li

DOI: https://doi.org/10.1016/j.apsusc.2023.157320

IF: 6.7

2023-08-01

Applied Surface Science

Abstract:Recently, the oxidation-coupled adsorption technologies for Sb(III) detoxification as well as adsorption are of great concern. To develop a kind of material for not only improving the Sb(III) adsorption efficiency but also enabling the oxidation of the adsorbed Sb(III) with low reagent or energy consumption, we prepared a magnetite-cuprite@chitosan bead adsorbent (nMC@CS) using a one-step method. Batch experiments and characterization of the beads demonstrated that Sb(III) adsorption was highly dependent on the Fe3O4 nanoparticles in the beads, and the adsorbed Sb(III) was oxidized by the reactive oxygen species (ROS) generated in-situ upon activation of the dissolved oxygen by Cu(I). Importantly, the Sb(III) adsorbed onto the surface of the beads could effectively catalyze the redox cycles of Fe(III)/Fe(II) and Cu(II)/Cu(I) in the system through the generation of O2 •– while being oxidized to Sb(V), forming a closed-loop circulation of electrons. This cyclic electron transfer facilitated the adsorption-oxidation process of Sb and further improved their synergistic efficiency. Under the optimal adsorption conditions, 97.4% of the Sb(III) in solution was adsorbed onto the nMC@CS, 84.3% of which was oxidized to Sb(V), providing a simple and promising strategy for efficient Sb(III) adsorption and simultaneous detoxification.

chemistry, physical,physics, applied, condensed matter,materials science, coatings & films
Adsorption properties of Cu2+, Cd2+ and Ni2+ by modified magnetic chitosan microspheres

LiMin Zhou,Yiping Wang,Qunwu Huang,Zhirong Liu

DOI: https://doi.org/10.3866/PKU.WHXB20071228

2007-01-01

Acta Physico-Chimica Sinica

Abstract:Fe3O4/chitosan magnetic microspheres of 50 to 80 μm were prepared using the inverse phase emulsion dispersion and chemical crosslinking technology, and then modified with ethylenediamine for use in the adsorption of heavy metal ions. The adsorption properties of the modified Fe3O4/chitosan toward Cu2+, Cd2+ and Ni2+ were investigated. It was found that the adsorption capacities of Cu2+ and Ni2+ increased with pH, and a maximum adsorption for Cd2+ occurred at pH=3. The saturated adsorption capacities calculated by Langmuir isotherms were 54.3 mg·g-1 for Cu2+, 20.4 mg·g-1 for Cd2+, and 12.4 mg·g-1 for Ni2+, respectively. The adsorption kinetics were well described by pseudo-second-order equation models. The experimental results showed that the Fe3O4/chitosan modified with ethylenediamine presented higher adsorption selectivity for Cu2+ than for Cd2+ and Ni2+ in all studied pH ranges. © Editorial office of Acta Physico-Chimica Sinica.
Regulation of Magnetic Properties of Magnetite by Doping with Transition Metal Elements

Yan-Ying Ren,Ya-Ning Li,Hong-Sheng Liu,Nan Xu,Kun Guo,Zhao-Hui Xu,Xin Chen,Jun-Feng Gao,Yanying Ren,Yaning Li,Hongsheng Liu,Zhaohui Xu,Jufeng Gao,,

DOI: https://doi.org/10.7498/aps.73.20231744

IF: 0.906

2024-01-01

Acta Physica Sinica

Abstract:Magnetic Fe 3 O 4 nanoparticles show promising applications in nanomedicine. The saturation magnetization (M S ) and magnetic anisotropy are critical for the applications of Fe 3 O 4 nanoparticles in drug delivery and magnetic hyperthermia. Here, by density functional computation, the doping effects of 3 d and 4 d transition metal elements (including Sc, Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, Y, Zr, Nb, Mo, Tc, Ru, Rh, Pd, Ag and Cd) on the magnetic properties of Fe 3 O 4 are carefully investigated. A conventional cell of Fe 3 O 4 , containing 24 Fe atoms and 32 O atoms, was used to investigate the doping of group III elements. One 3 d or 4 d atom is doped in one conventional cell of Fe 3 O 4 , resulting in a formula of X 0.125 Fe 2.875 O 4 where X represents the dopant. The results show that the doping of most 3 d and 4 d transition metal elements will decrease the total magnetic moment, while the doping of Ag, Zn and Cd in Fe 3 O 4 will increase the total magnetic moment by 19% ~ 22%. However, it is hard to dope Ag into Fe 3 O 4 according to the positive formation energy. Therefore, Zn and Cd are good candidates to improve the M S of Fe 3 O 4 . The doping of Zn and Cd has also influence on the magnetic anisotropy of Fe 3 O 4 . For Zn 0.125 Fe 2.875 O 4 , the magnetic anisotropy energy is about 0.25 meV per cell, which slightly larger than that of intrinsic Fe 3 O 4 (0.2 meV per cell). Interestingly, the doping of Cd (Cd 0.125 Fe 2.875 O 4 ) would greatly increase the magnetic anisotropy energy to 0.8 meV per cell, which is significant for the specific absorption rate in the magnetic hyperthermia application. In addition, the doping of Zn and Cd would not induce any defect states in the band gap according to the density of states. Zn 0.125 Fe 2.875 O 4 and Cd 0.125 Fe 2.875 O 4 are both semiconducting and both the top of valence band and the bottom of conduction band originate from octahedral Fe. This is because the impurity states are very deep in energy. Our results suggest that doping with Cd is a feasible way to improve the performance of Fe 3 O 4 as drug delivery and magnetic hyperthermia materials.

physics, multidisciplinary
Antimony Removal by a Magnetic TiO2/SiO2/Fe3O4 Nanosphere and Influence of Model Dissolved Organic Matter

Yangyang Chu,Xinyu Zhang,Xuefeng Yu,Chuanhao Yan,Yu Yang,Guofeng Shen,Xuejun Wang,Shu Tao,Xilong Wang

DOI: https://doi.org/10.1016/j.cej.2021.129783

IF: 15.1

2021-01-01

Chemical Engineering Journal

Abstract:Antimony (Sb) pollution is attracting increasing international concerns. In this work, a novel magnetic nanosphere TiO2/SiO2/Fe3O4 (TSF) was synthesized for antimony removal. The influence of four amino acids on antimony removal by TSF and the associated mechanisms were systematically investigated. The results showed that TSF has high Sb removal efficiency reaching up to 96%. The presence of lysine, glutamate, and arginine did not alter antimony removal at pH = 2-11, because they were not sorbed to TSF and did not bind antimony in the aqueous phase. In contrast, cysteine-led reduction in antimony removal by TSF tended to be more pronounced when pH increased from 2 to 11, with reduction percentage increasing from 0 at pH 2 to 79% at pH 11. XPS and RAMAN analysis showed the weak interaction between antimony and -NH2 and -COOH, but strong interaction with -SH. When solution pH increased from 2 to 11, the speciation changes of antimony, TSF, and cysteine thus their interaction changes caused antimony removal reduction. At pH = 2, cysteine formed intermolecular hydrogen bond network, limiting the coordination between -SH and antimony. When pH increased to 6 and finally to 11, the hydrogen bond network was gradually broken, and the -SH group gradually lost H+ and became -S- which more readily complexed with antimony. Therefore, competition of cysteine in liquid phase with TSF for antimony was enhanced. The complexation of antimony and cysteine in solution increased with increasing cysteine concentration, hence antimony removal efficiency by TSF gradually decreased.
Manganese doping of hematite enhancing oxidation and bidentate-binuclear complexation during As(III) remediation: Experiments and DFT calculation

Lin Liu,Zhihui Yang,Feiping Zhao,Zetang Chai,Weichun Yang,Hongrui Xiang,Qi Liao,Mengying Si,Zhang Lin

DOI: https://doi.org/10.1016/j.cej.2023.144758

IF: 15.1

2023-09-01

Chemical Engineering Journal

Abstract:Iron and manganese oxides are commonly found in nature, such as hematite and pyrolusite, which strongly affect the migration and transformation of As(III). In this study, a series of hematite materials modified by MnO2 (Hm-Mn) were synthesized to achieve the adsorption-oxidation bifunctionality of hematite toward As(III). The maximal As(III) adsorption capacity of Hm-Mn (80.0 mg g−1) was nearly 3 times higher than that of pure hematite (28.5 mg g−1). The ratio of As(V) immobilized on Hm-Mn reached 71.5%, which was significantly higher than that of Hm (17.9%). The kinetic results indicated that chemisorption is the dominant adsorption behavior. Density functional theory (DFT) calculations revealed that manganese modification reduced the adsorption and oxidation energy of Hm-Mn, confirming that manganese modification was beneficial to both of the adsorption and oxidation of As(III). Bidentate-binuclear complex was the primary coordination type of arsenic binding on the Hm-Mn facets. Crystal orbital Hamilton population (COHP) analysis implied that the bonding of Hm-Mn with arsenic was stable. Specially, the bonding of Fe-O-As was stronger than that of Mn-O-As. Altogether, Hm-Mn provides a feasible solution for arsenic-contaminated water, and the fundamental theoretical data offer new perspective for understanding the remediation mechanisms of variable valence metal pollutants.

engineering, chemical, environmental
A biochar supported magnetic metal organic framework for the removal of trivalent antimony

Guocheng Zhu,Jialin Lin,Qian Yuan,Xiaofeng Wang,Zilong Zhao,Andrew S Hursthouse,Zhenghua Wang,Qingbo Li,Andrew S. Hursthouse

DOI: https://doi.org/10.1016/j.chemosphere.2021.131068

IF: 8.8

2021-11-01

Chemosphere

Abstract:Metal organic framework (MOF) nanoparticles are recognized for their effective removal of metal ions from aqueous systems. However, the application of nanoparticles in a powder form as synthesized is not practical and recovery is not easy. We prepared a recyclable magnetic MOF nanoparticle phase and used a widely available waste biomass to generate biochar to support magnetic nanoparticles applied in the treatment of aqueous antimony pollution. A mushroom waste biochar was used to support a magnetic UIO-66-2COOH (denoted as BSMU). Adsorption of trivalent antimony (Sb (III)) onto the BSMU was evaluated. The results showed that optimum conditions for preparation of the BSMU were the mass ratio of MMOF to biochar 4:1, the temperature 70 °C, the time 4 h, and the initiator 4 mM. Under such conditions, sorption capacity reached 56.49 mg/g for treatment of Sb (III) solution at 100 mg/L and pH 9.1. Alkaline conditions (such as pH 9.1) are more favorable for adsorption than acidic conditions, and coexisting ions including NO3−, Cl−, SO42−, and PO43− had no significant negative effect in adsorption, and with the use of low dose, higher adsorption density achieved. The adsorption followed a pseudo second order kinetics model and Freundlich isotherm model. It resulted in a higher enthalpy changes (<math>ΔHθ</math>) and activation energy (Ea) of 97.56 and 8.772 kJ/mol, respectively, and enhanced the rate pf random contact between antimony and the BSMU, as indicated by a higher entropy change (<math>ΔSθ</math>) up to 360 J/mol·K. As a result, it readily absorbs antimony. These adsorption properties identified in this study would provide a valuable insights into the application of nanoparticles loaded biochar from abundant biomass in environmental remediation.

environmental sciences
Efficient removal of antimony by a facile liquid-controlled strategy reinforced hematite-spinel (Fe2O3-MnFe2O4) composite: construction, simulation and practical evaluation

Tianning Wang,Yonghong Jiao,Mengchang He,Xianjia Peng,Peng Liu,Wei Ouyang,Chunye Lin,Xitao Liu,Haijiao Xie

DOI: https://doi.org/10.1016/j.cej.2022.138974

IF: 15.1

2023-01-01

Chemical Engineering Journal

Abstract:Currently, aqueous antimony contamination has become a non-negligible issue due to its scale industrious production and potential health risk. Herein, we prepare a novel hematite-spinel (Fe2O3-MnFe2O4) adsorbent by a one-step hydrothermal method for aqueous antimony deep purification, in which interfacial Fe-Mn bidentate complex sites are determined as the reinforced one by X-ray absorption spectroscopy (XAS) analysis and density functional theory (DFT) simulation. Through facile alkaline control by NH3·H2O and Fe/Mn proportion adjustment, the intrinsic synthesis kinetics of materials are precisely regulated that MnFe2O4 nano-particles successfully in-situ form on the Fe2O3 surface, in which sufficient adsorption sites are guaranteed by the small size effect. The adsorption experiment further demonstrates that the composite material is effective in Sb(III) and Sb(V) elimination, in which the adsorption capacity reaches up to 42.7 (Sb(III)) and 32.4 mg·g−1 (Sb(V)) (initial concentration 5.0 mg·L−1). The Sb K edge Extended X-ray absorption fine structure (EXAFS) analysis shows that antimony molecules occur as two typical complexation forms on the MnFe2O4 interface, in which an edge-sharing with Fe-O octahedron (Fe-Fe-ES) and two corner-sharing with Fe-O octahedron and Mn-O tetrahedron (Fe-Mn-CS) are exhibited. Further DFT calculations indicate that the Fe-Mn-CS has the highest adsorption energy for Sb(III) (-3.31 eV) and Sb(V) (-5.12 eV), which is rationally interpreted by the compatible overlapping of Fe 3d and O 2p as well as interfacial electron redistribution in Mn atom. This work may represent a new strategy in structure design and provide an alternative perspective in adsorption mechanism illustration.

engineering, chemical, environmental
Biosynthesized Magnetite-Perovskite (Xfe2o4-Bifeo3) Interfaces for Toxic Trace Metal Removal from Aqueous Solution

Jianan Nie,Liang Bian,Xiaobin Gu,Xiaoqiang Jiang,Hailiang Dong,Mianxin Song,Faqin Dong,Limin Zhang,Huichao He,Ping He,Nelson Belzile,Yuwei Chen,Shuhui Sun

DOI: https://doi.org/10.1016/j.ceramint.2018.08.167

IF: 5.532

2018-01-01

Ceramics International

Abstract:X-modified magnetite (XFe2O4; X = Cr, Mn, Fe, Co or Ni) was synthesized from goethite reduction, and inserted into the Fe -vacancy of perovskite (BiFeO3), via microbial Fe3+-> Fe2+ reduction by Shewanella (e.g. Shewanella oneidensis MR-1 and Shewanella putrefaciens CN32). We demonstrated that the average adsorption intensities of nine toxic trace metals (Cr3+, Mn2+, Co2+, Ni2+, Cu2+, Zn2+, Cd2+, Pb2+, and Hg2+), in Freundlich mode were 8.29-10.79 multiples higher than that in Langmuir mode, being more competitive than previously reported values. The fluorescence quenching is attributed to the orbital hybridization of molecular oxygen activation and trace metal (M) ions, which weakens the X2+-O-Fe3+-O-(Fe3+) coupling orbital. In addition Shewanella putrefaciens CN32 creates more oxygen vacancies to modify Ni down arrow -Fe down arrow-O down arrow d*-p hybridized orbitals for enhancing the local spin-orbit coupling with Cd-4d(10). This design idea can be extended to other direct biosynthetic magnetite-perovskite as highly efficient toxic trace metal removal agents.
Coupled Antimony(Iii) Sorption and Oxidation by Iron-Modified Biochar: Examining the Balance Between Electron Donating Capacity and Reactive Fe Species

Yurong Gao,Hanbo Chen,Zheng Fang,Nabeel Khan Niazi,Jianhong Li,Zhongzhen Liu,Nanthi Bolan,Bin Gao,Deyi Hou,Jun Meng,Wenfu Chen,Hailong Wang

DOI: https://doi.org/10.2139/ssrn.4264178

2022-01-01

SSRN Electronic Journal

Abstract:Sorption and oxidation are two key pathways for the decontamination of antimonite (Sb(III))-bearing water using iron (Fe)-enabled biochars (FeBCs). We investigated sorption and oxidation behavior of FeBCs for Sb(III) in aqueous solutions. Results revealed that Sb(III) removal by FeBCs was significantly improved, with FeBC prepared at 500Â°C (FeBC500) showing the maximum Sb(III) sorption (64 mg g-1). Density functional theory (DFT) calculations indicated that the magnetite (Fe3O4) in FeBC500 offered a sorption energy of -0.22 eV, being 5-time as that on non-modified case. With the addition of peroxymonosulfate (PMS), the sorption of Sb(III) on FeBC500 was 7-time higher than that on BC500. Electron transfer experiments showed FeBC500 had higher electron acceptor capacity (0.045 mmol e- (g biochar)-1), which promoted the efficient oxidation of Sb(III) (63.6%). This study provides new information which is key for the development of an effective biochar-based composite materials for the removal of Sb(III) from water and wastewater.
Antimonite oxidation and adsorption onto two tunnel-structured manganese oxides: Implications for antimony mobility

Xiangqin Wang,Yang Yang,Liang Tao,Mengchang He

DOI: https://doi.org/10.1016/j.chemgeo.2021.120336

IF: 3.9

2021-09-01

Chemical Geology

Abstract:Manganese (Mn) oxides have high oxidation and sorption capacities, which enables them to play important roles in antimony (Sb) migration and transformation. In this study, the oxidation and adsorption behaviors of antimonite (Sb(III)) on two tunnel-structured Mn oxides, pyrolusite (β-MnO2) and manganite (γ-MnOOH), were investigated and compared using batch kinetic techniques; the adsorption isotherms, edges and spectroscopic characteristics of Sb(III) and Sb(V) on the two minerals were also compared and modeled. The adsorption isotherms and edges indicated that the affinity of Sb(III) and Sb(V) toward the two Mn oxides depended on the Sb species, the pH of the solution and the characteristics of the two minerals. Acidic pH favored the sorption of both Sb(III) and Sb(V) onto the two minerals, with the rate of sorption decreasing subsequently with the increase in pH. The sorption capacity of β-MnO2 for both Sb(III) and Sb(V) was much lower than that of the γ-MnOOH. Sb(V) was the main species after Sb(III) and Sb(V), which adsorbed onto the surface of both β-MnO2 and γ-MnOOH. Furthermore, Sb(V) combined with γ-MnOOH through inner-sphere complexation and with β-MnO2 through outer-sphere complexation. These results therefore provide new insights into the mechanism of Sb(III) oxidation and adsorption on the surfaces of two tunnel-structured Mn oxides and indicates that γ-MnOOH would exhibit a huge capacity in Sb oxidation and sorption.

geochemistry & geophysics
Tuning the Interfacial Properties of Spinels to Improve the Antimony Adsorption Ability

Yulu Ai,Can Wu,Guo Liu,Hongxi Wang,Chaojiang Yao,Huabin Li,Zhike Li

DOI: https://doi.org/10.1021/acs.langmuir.1c00978

IF: 3.9

2021-08-13

Langmuir

Abstract:Structure and interfacial properties are important factors that affect a spinel's adsorption performance. In this article, by changing the water content in a precursor during synthesis, the interfacial properties of normal and inverse spinels were tuned to improve Sb adsorption. The results showed that changing the water content did not alter the crystal structure of synthesized zinc ferrite (ZnFe2O4) and cobalt ferrite (CoFe2O4), but it had a significant effect on the crystallite size and the number of surface hydroxyl groups. For normal spinel ZnFe2O4 and inverse spinel CoFe2O4, the crystallite size decreased while the surface hydroxyl groups increased when the water content gradually increased from 1 to 8 mL. Spinels with smaller crystallite size and more surface hydroxyl groups enhanced Sb adsorption. The adsorption capacity of ZnFe2O4 and CoFe2O4 for low concentrations of Sb(V) increased from 8.45 and 10.64 mg/g to 15.05 and 17.00 mg/g, respectively. This work has greatly improved the adsorption capacity of spinel materials through a simple tunable method and is expected to provide new ideas for the interfacial tuning of spinel materials, which shows great potential applications for wastewater treatment.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acs.langmuir.1c00978.XRD patterns of ZnFe2O4 and CoFe2O4 nanoparticles synthesized by adding 20 mL of H2O in the precursor solution; GC–MS chromatograms of the solutions of ZnFe2O4 and ZnFe2O4; XPS spectra of ZnFe2O4 and CoFe2O4; and Langmuir and Freundlich isotherm parameters for Sb(V) adsorption (PDF)This article has not yet been cited by other publications.

chemistry, multidisciplinary, physical,materials science
Facile synthesis of nanosheet-assembled γ-Fe2O3 magnetic microspheres and enhanced Sb(III) removal

Wenlin Zhao,Bozhi Ren,Andrew Hursthouse,Zhenghua Wang

DOI: https://doi.org/10.1007/s11356-020-11727-7

Abstract:The development and utilization of magnetic nanoadsorption materials with large adsorption capacity and easy separation are the research hotspot nowadays. In this study, nanosheet-assembled maghemite (γ-Fe2O3) magnetic microspheres were successfully synthesized by an environmental friendly, quick, and simple method, for enhanced Sb(III) removal from aqueous solution. Scanning electron microscopy (SEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), vibrating sample magnetometer (VSM), and Brunauer-Emmett-Teller (BET) were used to characterize the material. The results showed that the product contained flower-like γ-Fe2O3 microspheres composed of petal-shaped nanosheets interspersed with each other. The specific surface area and pore volume were 69.23 m2/g and 0.15 cm3/g, respectively. The material has a strong magnetic response, which allows rapid solid-liquid separation under the action of an external magnetic field. The effects of different dosages, solution pH, and contact time on the adsorption effect were studied by batch adsorption experiments, and the reusability of the materials was evaluated. Both Freundlich isothermal adsorption model and pseudo-second-order kinetic model were able to describe the uptake of Sb(III). The maximum adsorption capacity of the material was 47.48 mg/g under optimal conditions. The adsorption mechanism is mainly that Sb and lattice oxygen (OX2-) form Fe-O-Sb coordination bonds, which is incorporated into the crystal structure of γ-Fe2O3 as inner-sphere surface complexes. The synthetic material has the advantage of simple preparation process, good adsorption capacity, operation over a wide range of pH, and easy physical separation from treatment systems with good potential for future application to treat polluted wastewater.
Single-ion Copper Doping Greatly Enhances Catalytic Activity of Manganese Oxides Via Electronic Interactions.

Xiaolei Hu,Shuya Li,Yaxin Chen,Weiye Qu,Junxiao Chen,Zhen Ma,Xingfu Tang

DOI: https://doi.org/10.1039/c9cc07669g

IF: 4.9

2020-01-01

Chemical Communications

Abstract:Single-ion copper doping greatly enhances catalytic activity of manganese oxides via electronic interactions between copper ions and manganese ions.
Removal of trace concentration Sb(V) in textile wastewater by Mn-doped Fe3O4: The mechanisms of Mn affect adsorption performance

Chunke Yang,Yue Pang,Yu Han,Xiaohui Zhan,He Wang,Junyan Liu,Rui Gao,Haoran Liu,Huixiang Shi

DOI: https://doi.org/10.1016/j.micromeso.2022.112150

IF: 5.876

2022-09-01

Microporous and Mesoporous Materials

Abstract:Mn-doped Fe3O4 with different Mn/Fe ratios were synthesized to remove 200 μg/L aqueous Sb(V) in simulated textile wastewater under neutral pH. The synthesized materials were characterized by XRD, XPS, and FTIR to confirm the Mn had been successfully doped into the lattice of Fe3O4. The optimum ratio of initial Mn/Fe appeared at 1:3, with the actual Mn/Fe ratio of 0.22, which was determined by the acid digest experiment. In contrast to the original Fe3O4, Mn doping increased the maximum adsorption capacity from 64.66 mg/g to 176.03 mg/g, and the adsorption capacity for 200 μg/L Sb(V) was enhanced from 0.74 mg/g to 1.51 mg/g. Mn affects the adsorption performance of materials through three main methods, decreased the particle size by hampering the crystal growth, which brought increased specific surface area leading to a higher adsorption capacity; reduced the distribution of Fe on the surface of materials, which results in lower adsorption capacity; increased the binding energy of Fe–O bonds, thus reducing the number of hydroxyl groups on the surface of materials, thereby reduce the adsorption capacity of the material. Synthesized Mn-doped Fe3O4 possesses good magnetic separation performance and reusability, thus could be a promising adsorbent to remove trace concentration Sb(V) in aqueous solutions.

materials science, multidisciplinary,chemistry, physical,nanoscience & nanotechnology, applied
Effects of Cu Nanopowders Addition on Magnetic Properties and Corrosion Resistance of Sintered Nd–Fe–B Magnets

X. G. Cui,M. Yan,T. Y. Ma,L. Q. Yu

DOI: https://doi.org/10.1016/j.physb.2008.09.002

IF: 2.988

2008-01-01

Physica B Condensed Matter

Abstract:Sintered permanent magnets have been prepared by blending Nd–Fe–B jet-milled powders with Cu nanopowders (0, 0.05, 0.1 and 0.2wt%) before pressing in a perpendicular magnetic field. Permanent magnetic properties, Curie temperature (Tc), microstructures and corrosion resistance of the sintered magnets were investigated. Microstructural characterization revealed that the grain size of Nd2Fe14B phase was refined and more homogeneous, and the grain boundaries became clear and smooth by the addition of Cu nanopowders, resulting in the improvement of coercivity Hcj. Moreover, the corrosion resistance of Nd–Fe–B magnets was also improved. However, Tc remained nearly unchanged with Cu addition, which was consistent with the elemental analysis results. Cu was not detected in the matrix phase Nd2Fe14B, but concentrated in the intergranular region.
Ion-Doped Iron-Based nanoparticles with enhanced magnetic properties: Synthesis and formation mechanism via coprecipitation

Zhuang Deng,Yu Wang,Shuo Zhang,Jingyi Wu,Shuning Wei,Zhen Jiao

DOI: https://doi.org/10.1016/j.jmmm.2024.172588

IF: 3.097

2024-10-20

Journal of Magnetism and Magnetic Materials

Abstract:Iron-based magnetic nanoparticles have gained significant attention in biomedicine. However, the magnetic properties of iron-based nanoparticles prepared through coprecipitation methods often do not meet application requirements. This study aims to enhance the performance of iron-based magnetic nanoparticles by synthesizing them via the coprecipitation method and doping them with Mn 2+ , Zn 2+ , and Co 2+ ions in various ratios. Among these, Zn-doped nanoparticles with a 0.6 ratio (ZION-6) exhibits the highest saturation magnetization intensity of 98 emu/g sample and the highest r 2 values of 165.2 mM −1 ·s −1 , making them an effective T 2 MRI contrast agent. Our investigation into the coprecipitation process revealed a formation mechanism for ion-doped magnetic iron-based nanoparticles. This mechanism involves the formation of an intermediate phase, α-FeOOH, followed by phase transformation, ion doping, and the aggregation of small particles to yield the final magnetic nanoparticles. This research could pave the way for developing magnetic nanoparticles with improved properties for biomedical applications.

materials science, multidisciplinary,physics, condensed matter
Stability improvement of Fe3S4 for peroxymonosulfate activation by trace Mn doping

Xiwen Liu,Fangshu Qu,Shanshan Gao,Zhaoyu Bai,Jiayu Tian

DOI: https://doi.org/10.1016/j.cej.2023.146291

IF: 15.1

2023-11-01

Chemical Engineering Journal

Abstract:Iron sulfide has a great prospect in the field of peroxymonosulfate (PMS) activation due to its high catalytic activity. However, the weak stability of iron sulfide has become an important disadvantage limiting its application. In this study, trace amount of Mn was doped into Fe3S4 with the purpose of reducing metal leaching and improving catalytic efficiency. It was found that trace Mn doping could increase the Fe-S bond energy, thus the structure stability was enhanced and metal leaching was decreased. Moreover, a new (220) plane (3.49 Å) was observed on the surface of trace Mn doped Fe3S4 in addition to the conventional (311) plane. Molecular modelling indicated that the (220) crystal plane was more compact than the (311) crystal plane, which was believed to play an important role in decreasing the metal leaching. Furthermore, a reduction in oxidation potential and electrochemical impedance was also observed for the trace Mn doped Fe3S4, which promoted more efficient activation of PMS to produce higher amount of reactive oxygen species (ROS). Quenching tests and EPR analysis demonstrated both sulfate radicals and singlet oxygen were generated in the PMS activation process, in which the singlet oxygen was the dominant ROS for BPA degradation. This work provides a new idea for the design of stable and efficient iron sulfide catalytic materials.

engineering, chemical, environmental

Enhanced Oxidative and Adsorptive Capability Towards Antimony by Copper-Doping into Magnetite Magnetic Particles

Enhanced mechanism of copper doping in magnetic biochar for peroxymonosulfate activation and sulfamethoxazole degradation

Synthesis of Ce(III)-doped Fe3O4 Magnetic Particles for Efficient Removal of Antimony from Aqueous Solution.

Design of Magnetic Nanoparticles with High Magnetic Separation Efficiencies and Durability for Cu2+ Adsorption

Enhanced adsorption-oxidation of Sb(III) over chitosan bimetallic beads: In-situ generated O2•– and autocatalytic effect of Sb(III)

Adsorption properties of Cu2+, Cd2+ and Ni2+ by modified magnetic chitosan microspheres

Regulation of Magnetic Properties of Magnetite by Doping with Transition Metal Elements

Antimony Removal by a Magnetic TiO2/SiO2/Fe3O4 Nanosphere and Influence of Model Dissolved Organic Matter

Manganese doping of hematite enhancing oxidation and bidentate-binuclear complexation during As(III) remediation: Experiments and DFT calculation

A biochar supported magnetic metal organic framework for the removal of trivalent antimony

Efficient removal of antimony by a facile liquid-controlled strategy reinforced hematite-spinel (Fe2O3-MnFe2O4) composite: construction, simulation and practical evaluation

Biosynthesized Magnetite-Perovskite (Xfe2o4-Bifeo3) Interfaces for Toxic Trace Metal Removal from Aqueous Solution

Coupled Antimony(Iii) Sorption and Oxidation by Iron-Modified Biochar: Examining the Balance Between Electron Donating Capacity and Reactive Fe Species

Antimonite oxidation and adsorption onto two tunnel-structured manganese oxides: Implications for antimony mobility

Tuning the Interfacial Properties of Spinels to Improve the Antimony Adsorption Ability

Facile synthesis of nanosheet-assembled γ-Fe2O3 magnetic microspheres and enhanced Sb(III) removal

Single-ion Copper Doping Greatly Enhances Catalytic Activity of Manganese Oxides Via Electronic Interactions.

Removal of trace concentration Sb(V) in textile wastewater by Mn-doped Fe3O4: The mechanisms of Mn affect adsorption performance

Effects of Cu Nanopowders Addition on Magnetic Properties and Corrosion Resistance of Sintered Nd–Fe–B Magnets

Ion-Doped Iron-Based nanoparticles with enhanced magnetic properties: Synthesis and formation mechanism via coprecipitation

Stability improvement of Fe3S4 for peroxymonosulfate activation by trace Mn doping