Abstract:Despite the rapid progress that has been made in increasing the power conversion efficiency (PCE) of organic solar cells (OSCs) over the past decade, it is a challenge to realize efficient and environment-friendly OSCs. In this contribution, all polymer solar cells were fabricated with a blend of poly[4,8-bis(5-(2-ethylhexyl) thiophen-2-yl) benzo[1,2-b: 4,5-b'] dithiophene-co-3-fluorothieno[3,4-b] thiophene-2-carboxylate] (PTB7Th) donor and vinylene-bridged perylenediimide-based polymer (PDI-V) acceptor, in which non-halogenated tetrahydrofuran (THF) was used as the host solvent. A conventional device structure of ITO/poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS)/PTB7-Th:PDI-V/zirconium acetylacetonate (ZrAcac)/Al was employed, where PEDOT:PSS functioned as the hole transporting layer (HTL) and ZrAcac functioned as the electron transporting layer (ETL). The mixed solution of PTB7-Th and PDI-V was spin cast on the top of PEDOT:PSS layer to form the active layer. After that, ZrAcac solution was spin cast on the top of PTB7-Th:PDI-V layer. Different thermal annealing temperatures were used to optimize the active layer morphology. In details, OSCs without thermal annealing showed a PCE of 7.1%, with a short-circuit current (J(SC)) of 14.9 mA/cm(2), an open-circuit voltage (V-OC) of 0.74 V, and a fill factor (FF) of 64%. The devices annealed at 120 degrees C showed a high PCE of 8.1% with a J(SC) of 15.5 mA/cm(2), a V-OC of 0.74 V, and a FF of 70%. Further increasing the annealing temperature to 150 degrees C led to decreased FF and thereby a relatively lower PCE (7.4%). To the best of our knowledge, the PCE of similar to 8.1% is one of the highest PCE values reported in the literature so far for all polymer solar cells. The high and balanced hole and electron mobility partially contributed to such a high performance. These results suggest that THF as good non-halogenated solvent can be used to fabricate high-performance all polymer solar cells. Higher efficiency can be achieved for OSCs with THF solvent when better polymer acceptors are employed.

Highly efficient aqueous-processed polymer/nanocrystal hybrid solar cells with an aqueous-processed TiO2 electron extraction layer

Self-Assembled Amphiphilic Block Copolymers/Cdte Nanocrystals for Efficient Aqueous-Processed Hybrid Solar Cells

Functions of Self-Assembled Ultrafine TiO2 Nanocrystals for High Efficient Dye-Sensitized Solar Cells

Efficient polymer/nanocrystal hybrid solar cells fabricated from aqueous materials

Fabrication of TiO 2 nanorod array/semiconductor nanocrystal hybrid structure for photovoltaic applications

Silicon Nanocrystal Conjugated Polymer Hybrid Solar Cells with Improved Performance

Unraveling Charge Separation and Transport Mechanisms in Aqueous‐Processed Polymer/CdTe Nanocrystal Hybrid Solar Cells

Interface Engineering For Both Cathode And Anode Enables Low-Cost Highly Efficient Solution-Processed Cdte Nanocrystal Solar Cells

Optimization Of Processing Solvent And Film Morphology To Achieve Efficient Non-Fullerene Polymer Solar Cells Processed In Air

Aqueous-Processed Inorganic Thin-Film Solar Cells Based on CdSe(x)Te(1-x) Nanocrystals: the Impact of Composition on Photovoltaic Performance.

Highly Efficient Ultraviolet Photodetectors Based on TiO2nanocrystal–polymer Composites Via Wet Processing

High-performance All Polymer Solar Cells Fabricated with Non-halogenated Solvent

High-Performance Ultrathin Organic-Inorganic Hybrid Silicon Solar Cells via Solution-Processed Interface Modification.

Water‐Based TiO2 Nanocrystal As an Electronic Transport Layer for Operationally Stable Perovskite Solar Cells

Aqueous Solution Processed, Ultrathin ZnO Film with Low Conversion Temperature As the Electron Transport Layer in the Inverted Polymer Solar Cells

High-efficiency solution-processed CdTe nanocrystal solar cells incorporating a novel crosslinkable conjugated polymer as the hole transport layer

Supercritical Fluid Processing of Mesoporous Crystalline Tio2 Thin Films for Highly Efficient Dye-Sensitized Solar Cells

A Highly Efficient Polymer Non-Fullerene Organic Solar Cell Enhanced by Introducing a Small Molecule As a Crystallizing-Agent

Charge Transport Properties of Low Temperature Solution Processable Poly(3-Hexylthiophene)/Surface Modified Tio2 Bulk Heterojunction Systems

NiOx Nanocrystals with Tunable Size and Energy Levels for Efficient and UV Stable Perovskite Solar Cells

Nano-structured Electron Transporting Materials for Perovskite Solar Cells.