Abstract:Lithium-sulfur (Li-S) batteries are widely regarded as the next-generation energy storage technology, due to their high potential in energy density and a low projected cost. Practical applications of such batteries are plagued with radical challenges that mainly stem from two factors. First, both sulfur and its final lithiation product, Li2S, are insulating. Thus, the reaction kinetics is slow and often leads to a low attainable capacity. Second, active material dissolve in the electrolyte in the form of lithium polysulfides. This dissolution causes a series of problems, including loss of cathode materials by diffusion away from the cathode, collapse of the cathode structure, and the polysulfide shuttle effect. As a result, Li-S batteries commonly show fast capacity decay and low coulombic efficiency. Herein, we report the exceptional battery performance of porous carbon-sulfur composite microspheres, PSC-S, that benefited from simultaneous control of nanostructure and microscale particle morphology. The porous carbon microspheres (PSC) was synthesized as the sulfur host,by combining emulsion polymerization and evaporation-induced self-assembly (EISA) process, with a good control of both pore structure and microscale particle morphology. Such material not only demonstrated superioty in attainable capacity, but also in several other critical parameters for the development of high-energy Li-S batteries. PSC-S composite boasts a high tap density of 1.08 g/ml and contains 75 wt.% sulfur embedded into the mesopores of its carbon framework. At a high sulfur loading of 5 mg-S/cm2 and 60wt.% sulfur content in the electrode, this material delivers both high gravimetric and high volumetric capacity with excellent retention. Carbon nanotubes (CNTs) can also be readily incorporated into the microspherical structure in the synthesis process to form a porous spherical carbon-carbon nanotube-sulfur composite (PSC-CNT-S). CNT incorporation effectively raises the conductivity of the composite, and thus significantly improves its high-rate performance. At a high current density of 2.8 mA/cm2, an initial capacity of 1100 mAh/g and a reversible capacity of 700 mAh/g after 200 cycles were achieved in PSC-CNT-S. The resultant areal capacity of over 3.5 mAh/cm2 is much higher than in previous reports of Li-S cathodes fabricated using coating techniques.

Mesoporous Carbon Materials Prepared from Litchi Shell As Sulfur Encapsulator for Lithium-Sulfur Battery Application

A Novel Mangosteen Peels Derived Hierarchical Porous Carbon for Lithium Sulfur Battery

Facile and Scalable Synthesis of Micro-Mesoporous Carbon/magnesium Oxide/sulfur Composite for Lithium-Sulfur Batteries

Mangosteen Peel-Derived Porous Carbon: Synthesis and Its Application in the Sulfur Cathode for Lithium Sulfur Battery

Controllable synthesis of mesoporous carbon microspheres with renewable water glass as a template for lithium-sulfur batteries.

A One-Step Hard-Templating Method for the Preparation of a Hierarchical Microporous-Mesoporous Carbon for Lithium-Sulfur Batteries

Mesoporous Carbon-Sulfur Composite Microspheres with Multiscale Morphology Control to Achieve High Areal Capacity for Lithium-Sulfur Battery Cathodes

Enhancing polysulfide confinement and conversion in meso-/microporous core-shelled MoC/NC microspheres for lithium-sulfur batteries

A Highly Ordered Meso@microporous Carbon-Supported Sulfur@smaller Sulfur Core-Shell Structured Cathode for Li-S Batteries.

Confining Small Sulfur Molecules in Peanut Shell-Derived Microporous Graphitic Carbon for Advanced Lithium Sulfur Battery

Synthesis and Electrochemical Performance of Micro-Mesoporous Carbon-Sulfur Composite Cathode for Li–S Batteries

Preparation of Mesohollow and Microporous Carbon Nanofiber and Its Application in Cathode Material for Lithium–sulfur Batteries

Mesoporous Carbon Prepared by Etching Halloysite Nanotubes (hnts) with Pyrrole As a Precursor for a Sulfur Carrier of Superior Lithium–sulfur Batteries

Activated Carbon with Ultrahigh Specific Surface Area Synthesized from Natural Plant Material for Lithium–sulfur Batteries

Cobalt-loaded three-dimensional mesoporous carbon as sulfur host for lithium‐sulfur batteries

Mesoporous carbon-carbon nanotube-sulfur composite microspheres for high-areal-capacity lithium-sulfur battery cathodes.

Preparation of mesoporous carbon and its effect on properties of lithium-sulfur batteries

Micro-mesoporous Carbon Nanofibers Loaded with Sulfur As a Self-Supported Cathode for High-Performance Li-S Batteries

Highly Ordered Nitrogen-Rich Mesoporous Carbon Derived from Biomass Waste for High-Performance Lithium–sulfur Batteries

Preparation and Electrochemical Performance of Sulfur/ Mesoporous Carbon Composites As Cathodes for Lithium-Sulfur Batteries

Ordered Micro-Mesoporous Carbon Spheres Embedded with Well-Dispersed Ultrafine Fe3C Nanocrystals As Cathode Material for High-Performance Lithium-Sulfur Batteries