Abstract:In this paper, we study the deformation behavior of nickel-based superalloys by in-situ EBSD and uniaxial tensile tests. This study mainly focuses on the microstructure evolution in the same area of the sample during deformation, including the evolution of various types of grain boundaries, geometrically necessary dislocations, grain orientations and texture, and their effect on the mechanical properties. The results show that the rotation of grains is closely related to their initial orientation during deformation. The lattice of grain is rotated to a certain extent to accommodate the more favorable orientation under low strain, leading to higher Schmid factors for the sample. Under large stresses, the grains occur deformation, multiple slip systems start simultaneously or alternately and the Schmid factors value gradually tends to stabilize at a lower level. Meanwhile, the texture orientation density of the initial Rotating cubic {001} texture, α-fiber (RD// ) texture, and γ-fiber (ND // ) gradually decrease or even disappears, while the texture orientation density of Copper {112} and Goss {011} increases during uniaxial tensile deformation for Cr20Ni80 alloy. Grain rotation may be a result of large strain due to stress triaxiality and resulting plane stress condition owing to specimen dimension, which is beneficial to improve the plastic deformability of the alloy. Interestingly, with the increase of strain, the average misorientation angle first decreases and then increases, which is associated with the dislocation density. In addition, serious torsion occurs in the grains during this process, forming a large number of substructures. These substructures result in grain refinement and the Hall-Petch effect. In fact, during the deformation process, multiple strengthening mechanisms act in coordination, leading to an increase in the strength of the alloy.

Deformation Mode Transition of Mg-3li Alloy: an in Situ Neutron Diffraction Study

Deformation behavior of Mg-8.5wt.%Al alloy under reverse loading investigated by in-situ neutron diffraction and elastic viscoplastic self-consistent modeling

In-situ Investigation Via High Energy X-ray Diffraction of Stress-Induced(0002)α→(110)β Transformation in a Ti-5.5Mo-7.2Al-4.5Zr-2.6Sn-2.1Cr Alloy

In Situ Monitoring of Dislocation, Twinning, and Detwinning Modes in an Extruded Magnesium Alloy under Cyclic Loading Conditions

Effects of Deformation Mechanisms on Texture Evolution and Mechanical Response of the Mg-1Al-0.5Mn-0.3Gd Alloy Under Plane Tension

Microstructures, hot tensile deformation behavior and constitutive modeling in a superlight Mg-2.76Li-3Al-2.6Zn-0.39Y alloy

The Mechanism for Li-addition Induced Homogeneous Deformation in Mg-4.5 wt. % Li Alloy

Texture Evolution and Their Effects on the Mechanical Properties of Duplex Mg–Li Alloy

Operating slip modes and inhomogeneous plastic deformation of Mg-10Gd-3Y-0.5Zr alloy during compression

In-situ and ex-situ investigation of deformation behaviors of a dual-phase Mg−Ni−Y alloy

Mg-3Al-1Zn alloy deformed along different strain paths: Role of latent hardening

In-situ EBSD study of deformation behavior of nickel-based superalloys during uniaxial tensile tests

The deformation modes and transferability during low-cycle fatigue of Mg and Mg–3Y alloy

Deformation mechanism of high ductility Mg-Gd-Mn alloy during tensile process

Deformation and Fracture Mechanisms of an Annealing-Tailored "bimodal" Grain-Structured Mg Alloy

Twinning–Detwinning-Dominated Cyclic Deformation Behavior of a High-Strength Mg-Al-Sn-Zn Alloy during Loading Reversals: Experiment and Modeling

Evolution of deformation mechanisms and their orientation dependence in fine-grained Mg-3Gd during tension

Deformation behavior and phase transformation of a dual-phase Mg−8.9Li−2.7Al-0.85Si alloy under compression test at elevated temperatures

Effect of Icosahedral Phase on Crystallographic Texture and Mechanical Anisotropy of Mg–4%Li Based Alloys

γ′-size effect on the deformation microstructure and texture in a Ni-based superalloy using in-situ neutron diffraction

Mechanical properties and fracture behavior of Mg–3Al–1Zn alloy under high strain rate loading