Study of 2500 Units PCTC Resistance Performance with Experiment and CFD Calculation Method

孙小江,何炎平,谭家华

DOI: https://doi.org/10.3969/j.issn.1673-4807.2003.06.001

2003-01-01

Abstract:Presents the principal characteristics of 2500 units pure car truck carrier(PCTC), then takes a study on its resistance performance by model tests and computational fluid dynamics(CFD) .

What problem does this paper attempt to address?

Study on the Resistance of a Large Pure Car Truck Carrier with Bulbous Bow and Transom Stern

Xiaoqing Tian,Tianwei Xie,Zhangming Liu,Xianghua Lai,Huachen Pan,Chizhong Wang,Jianxing Leng,M. M. Rahman

DOI: https://doi.org/10.3390/jmse11101932

IF: 2.744

2023-01-01

Journal of Marine Science and Engineering

Abstract:The resistance of a large Pure Car Truck Carrier (PCTC) with a bulbous bow and a transom stern is evaluated in the present paper. Several cases at nine different ship speeds in calm water are simulated and results are compared with the experimental measurements. The maximum relative error is 0.93% at a Froude number (Fr) of 0.209. The total resistance coefficient of the ship in calm water shows a parabolic trend with increasing Fr, and it reaches a minimum value at Fr = 0.1794. Furthermore, the cases of the ship in regular waves with six different wavelengths and three wave heights are simulated. It is observed that the total resistance exhibits a quadratic relationship with the wavelength when the wave height is fixed. The wave-making resistance increases with the increase in wave height at any fixed wavelength, and it reaches a maximum value when the wave-length is 1.2 times the ship length (Lpp). Additionally, we also investigated the resistance in three different sea states at four different speeds. When the significant wave height of irregular waves is the same as regular waves, the wave-making resistance under irregular waves is much smaller than that of the regular waves. All of these results indicate that the bulbous bow and transom stern can reduce the wave-making and residuary resistances, which can provide a useful reference for the subsequent design and manufacturing of related ships.
A Study on Heat Transfer Model for the Dynamic Contact Boundary Between Piston Ring and Cylinder Liner

Zheng Sun,Yuqi Huang,Xiaoli Yu

DOI: https://doi.org/10.19562/j.chinasae.qcgc.2018.03.016

2018-01-01

Abstract:In fluid-solid coupling calculation of internal combustion engine,due to multiple thermal effects coupling,the calculation results by using empirical formulae or thermal resistance model are quite different from real situation. In view of this, on the basis of liner contact lubricating model, the changing law of different thermal effects with working conditions and their mutual coupling effects are studied and the piston ring / cylinder liner heat transfer model is established based on the correction on the results of CFD flow / heat transfer calculation. The re-sults indicate that compared with thermal resistance model, the simulation result of piston temperature distribution by the corrected heat transfer model proposed is closer to the piston temperature data measured, and the corrected model being normalized can be wider applied to other piston ring / cylinder liner heat transfer calculations.
Simulation and Analysis Method for the Operation Characteristics of CIT400 High-Speed Comprehensive Inspection Train Based on Predictive Current Control

FANG Youtong,LIU Li,MA Jien,PEI Chunxing

DOI: https://doi.org/10.3969/j.issn.1001-4632.2012.04.13

2012-01-01

Abstract:Based on the structure of traction drive system and the traction characteristics of CIT400 high-speed comprehensive inspection train,a simulation model was established by MATLAB/Simulink for the traction drive system of high-speed comprehensive inspection train under predictive current control.The operation characteristics of CIT400 high-speed inspection train were simulated and analyzed upon short-time power failure of pantograph and net voltage fluctuation under traction and brake conditions.Simulation results were compared with measured data.Research shows that the simulation result and measured data are basically identical.The established model can correctly reflect the operation characteristics of the train and can meet the dynamic and static requirements for the actual operation of train.
A method for ship resistance prediction based on CFD computation

范佘明,朱仁传,缪国平,倪崇本

DOI: https://doi.org/10.3969/j.issn1000-4874.2010.05.002

2010-01-01

Abstract:A method for ship resistance prediction based on CFD computation is outlined, with ship form factor obtained by solving the viscosity resistance of double-model in turbulence flow theory and the wave making resistance in ideal flow theory. Comparing with the experimental results of series-60 and KCS advancing with different speeds, the new method of ship resistance prediction is economical, practical and meets the engineering needs.
Design of Medium and Large Size Pure Car and Truck Carriers

Minjia Zhang

2010-01-01

Abstract:This paper describes typical design concepts,solution and key technology for contemporary medium and large size PCTCs(Pure Car and Truck Carrier).
Effects of External Perturbations on Dynamic Performance of Carbon Dioxide Transcritical Power Cycles for Truck Engine Waste Heat Recovery

Xiaoya Li,Hua Tian,Gequn Shu,Chen Hu,Rui Sun,Ligeng Li

DOI: https://doi.org/10.1016/j.energy.2018.08.137

IF: 9

2018-01-01

Energy

Abstract:Carbon dioxide transcritical power cycle (CTPC) systems are dynamically tested on a constructed test bench using an expansion valve. Effects of external perturbations of pump speed, expansion valve opening and engine conditions on dynamic performance of the CTPC systems are investigated with step changes. Dynamic characteristics are identified with rise time, settling time and overshoot. Results show that both a basic CTPC system and a CTPC system with a recuperator (R-CTPC) behave as a second-order underdamped system with the perturbations of pump speed and expansion valve opening. Overshoot or undershoot tends to appear in pressures when pump speed changes, while overshoot or undershoot occurs more noticeably in temperatures when expansion valve opening varies. Although the CTPC systems respond slowly with the perturbations of engine conditions, they have the ability to operate safely and produce power continuously. Therefore, the CTPC systems are robust when facing narrow fluctuations of heat sources while swift when required to make adjustments, showing great potential for truck engine waste heat recovery. Overall, current research gives a full understanding of the dynamic performance of the CTPC systems, which will provide references for dynamic model validation and possible control strategy identification.
Analysis on Automobile Coasting Resistance

Gao Youshan,Li Xinghu,Huang Min,Jiang Lei,Zhang Jichun

DOI: https://doi.org/10.3969/j.issn.1000-3703.2008.04.008

2008-01-01

Abstract:This paper has set up a calculation model for automobile coasting resistance.Based on the stipulations in 'Motor vehicles—General rules of road test method(GB/T12534-1990)'and'Motor vehicles—Coast down—Test method(GB/T 12536-1990)',this paper has carried out coasting tests under conditions of no load,semi-load and full load,and has equated the motion differential equation of coasting resistance calculation model based on tests data.Comparison of fuel consumption per 100 km between calculation results of coasting resistance model and road tests results,shows that the built-up coasting resistance calculation model has high calculation precision.
A Combined Computational Fluid Dynamics and Thermal–Hydraulic Modeling Approach for Improving the Thermal Performance of Corrugated Tank Transformers: A Comparative Study

Chunping Wang,Qingjun Sun,Ali Al-Abadi,Wei Wu

DOI: https://doi.org/10.3390/en17081802

IF: 3.2

2024-04-10

Energies

Abstract:In this study, we present a complete analysis of the thermal behavior of an oil-filled distribution transformer using two different approaches: numerically, by applying computational fluid dynamics (CFD) simulations; and analytically, by using thermal–hydraulic modelling (THM). The THM method becomes challenging when the corrugated transformer tank wall structures are complex, and therefore CFD simulations are required to provide in-depth details of the winding oil thermal–hydraulic behavior and to generate parameters for improving the THM calculation. The numerical and analytical thermal performance results were then compared with heat-run measurements of a case study transformer and the accuracy of both approaches on different thermal performance parameters was validated. This study has certain reference value for improving the thermal performance and operation efficiency of distribution transformers, and eventually aims to provide engineers with an effective tool to design the most efficient and reliable distribution transformers with corrugated tank walls for various applications.

energy & fuels
Models Used in V-I Measuring Curve of PTCR

hao yongde,fang tao,huang zhengwei,fu ming,zhou dongxiang

DOI: https://doi.org/10.3969/j.issn.1002-1841.2004.01.015

2004-01-01

Abstract:Analyses the static volt-ampere characteristic curve of positive temperature coefficient thermal resistor (PTCR) in detail.Recommend a mathematics method to deal with testing datum of PTCR’s volt-ampere characteristic on this basis-Least square method and nature sample function method.Compared with the method of software origin,they fit the data very well,what’s more,the curve drawn is more smooth,more close to the reality V-I cuvre than by Origin.
Comparative Study of 1800 V and 2400 V MCT and IGBT

Bo Zhang,Huang, A.Q.,Budong You,Zhaoji Li

DOI: https://doi.org/10.1109/icccas.2002.1179113

2002-01-01

Abstract:The carrier lifetime and buffer-layer parameters determine the power dissipations of modern power devices. In this paper, based on simulation results, the trade-off relationships between the on-state conduction loss and turn-off loss of the 1800 V and 2400 V N-MCTs (N-MOS controlled thyristors) and IGBTs are studied comparatively. The simulation shows that the N-MCT has a better performance than that of the IGBT in the area studied.
Comprehensive Physical Commutation Characteristic Analysis and Test of Hybrid Line Commutated Converter Based on Physics Compact Model of IGCT

Zhanqing Yu,Zongze Wang,Chaoqun Xu,Xuan Zhou,Zhengyu Chen,Chunpin Ren,Rong Zeng

DOI: https://doi.org/10.1109/tpel.2022.3213490

IF: 5.967

2023-01-01

IEEE Transactions on Power Electronics

Abstract:In order to mitigate commutation failure of high voltage direct current (HVdc) system, a novel hybrid line commutated converter (H-LCC) based on integrated gate commutated thyristor (IGCT) and thyristor has been proposed. To verify the proposed scheme's effectiveness and correctness, the physics-based compact model of reverse blocking IGCT (RB-IGCT) and physics-based model of thyristor are established in this article. By comparing the features of physics-based model with other simulation methods, it can be observed that the former has obvious advantages. On the basis, a simulation study of proposed H-LCC based on physics compact model of RB-IGCT and physics-based model of thyristor is conducted to analyze the physical commutation characteristics comprehensively, which is verified by equivalent commutation tests. The H-LCC can mitigate commutation failure of HVdc effectively and physics-based model of H-LCC is expected to be applied in the simulation of dc grid equipment and provide reference for commutation characteristics analysis and snubber parameter optimization that need rapid and multiple simulations.
Numerical and Experimental Study on Flow and Heat Transfer Performance of Some Compact Surface Recuperators

Hao PENG,Zhi-jiang SUN,Xiang LING

DOI: https://doi.org/10.13224/j.cnki.jasp.2008.01.022

2008-01-01

Abstract:A unit control model was established using computational fluid dynamic(CFD) method,while the heat transfer and fluid flow performances on primary surface of recuperator(stainless steel serrated fin and cross corrugated(CC) primary surface) were simulated numerically and also compared with the experimental results.The results show good consistency between numerical simulation and experimental data.To this end,the effect of CC surface structural parameters on heat transfer performance was discussed,and then the heat transfer and flow characteristics were compared for different structural scales and surface arrangements,thus providing a basis for design optimization of recuperators.
Study on Dynamic Thermal Control Performance of Positive Temperature Coefficient (PTC) Material Based on a Novel Heat Transfer Model Considering Internal Heat Transfer

Ruo-Jiang Wang,Yu-Hui Pan,Yong-Le Nian,Wen-Long Cheng

DOI: https://doi.org/10.1016/j.applthermaleng.2019.114452

IF: 6.4

2019-01-01

Applied Thermal Engineering

Abstract:Positive temperature coefficient (PTC) material is widely used in thermal control due to its unique characteristics. In this paper, a novel heat transfer model of PTC material is proposed with consideration given to the internal heat transfer characteristics of the model which was ignored in the previous model, and it is validated by conducting experiment. Based on this novel heat transfer model, the effects exerted by thermal conductivity, heat capacity and thermal contact resistance on the thermal control of PTC material that have never been studied in previous work are investigated. In this paper, the PTC material with large heat capacity will extend the equilibrium time of the controlled device significantly. Besides, the dynamic thermal control performance of PTC material is verified by carrying out simulation. Herein, thermal control of PTC material under three different ambient temperature conditions is studied. As indicated by the results, PTC material has better thermal control performance under variable ambient temperatures. When the ambient temperature varies periodically with 5 degrees C amplitude and for a period of more than 300 s, the temperature of controlled device barely changes.
Numerical Investigation on Handling Stability of a Heavy Tractor Semi-Trailer under Crosswind

Qianwen Zhang,Chuqi Su,Yi Zhou,Chengcai Zhang,Jiuyang Ding,Yiping Wang

DOI: https://doi.org/10.3390/app10113672

2020-05-26

Applied Sciences

Abstract:Due to the large lateral area of the trailer and variable road conditions, the handling stability of a heavy tractor semi-trailer under crosswind is very important for road safety. In this present work, numerical simulation is performed to study the crosswind effects on handling stability of a tractor semi-trailer. The aerodynamic characteristics of the tractor semi-trailer under different crosswind were computed by computational fluid dynamics (CFD). Then, mathematical models to reveal the relationship between the aerodynamic forces and crosswind were constructed to serve as inputs of the multi-body dynamics to analyze the handling stability under crosswind. The performance of crosswind stability is evaluated by the response of lateral acceleration, yaw rate and the lateral displacement. The lateral acceleration and yaw rate were decreased by a maximum of 14.6% and 16.5% compared to the truck without the deflector, which showed that the crosswind aerodynamics and stability were obviously improved.
Research of Resistance Estimation Method for High-Speed Catamaran

Chongjian ZHOU,Cungen LIU,Xuefeng WANG,Huiping FU

DOI: https://doi.org/10.3969/j.issn.1000-4882.2014.04.004

2014-01-01

Abstract:Because of the big difference between high-speed catamaran and low-speed ships, estimation of the resistance of high-speed catamaran with the methods used for low-speed ships will result in a serious error. In this paper various methods and CFD software are applied to calculate the total resistance of a 550t high-speed catamaran and compared with model tests. The method, in which viscous resistance and wave resistance is calculated separately, is more suitable to the estimation of the resistance for high-speed catamaran.
The Study of Arc Rate, Friction, and Wear Performance of C/C Composites in Pantograph–Catenary System

Huijie Zhang,Lemin Sun,Yongzhen Zhang,Bao Shangguan

DOI: https://doi.org/10.1080/10402004.2014.939319

IF: 2.056

2014-01-01

Tribology Transactions

Abstract:A series of tests on arc rate, friction coefficient, and wear rate of electrical current collectors sliding against overhead contact wires under different conditions was carried out on a high-speed friction and wear testingmachine with a pin-on-disc configuration. The worn surface morphology and composition were examined using a scanning electron microscope and energy dispersion spectrum analyzer, respectively. The effects of current, velocity, and load on the arc rate, friction coefficient, and wear rate of C/C composites/QCr0.5 couples were investigated, and the influence mechanism of test parameters on C/C composites was explained. It is concluded that the wear rate increases with an increase in current and velocity and has a decreasing trend with the increase in load. The friction coefficient increases with an increase in velocity and load. The arc rate of C/C composites/QCr0.5 couples increases with an increase in current and velocity. Under the condition of the same current and velocity, when the load is 70 N, the arc rate is the lowest.
Study of Resistance Performance of Vessels with Notches by Experimental and Computational Fluid Dynamics Calculation Methods

Xun Shi,Xin-quan Chen,Jia-hua Tan

DOI: https://doi.org/10.1007/s12204-010-1014-2

2010-01-01

Abstract:Owing to the special working characteristics and operation requirements, lots of working ships have notches in different sizes and shapes in their hulls. In order to study the resistance performance of the vessel with notches, a series of model resistance tests were performed in respect to the 4 500 m3/h cutter suction dredger, and the tests were simulated based on the computational fluid dynamics software FLUENT. Based on analysis to the experimental data and the computational fluid dynamics (CFD) calculation results, the change of the flow field and the resistance performance caused by the notches were studied, and the reliability of the software in simulation of viscous flow around the hull was proved. It provides the basis for the future study and the design optimization of this kind of working ships.
Study of customer correlation bench test spectrum of charge air cooler of semi-trailer truck

Yu Han,Liang Hong,Zhonghua Xie,Ce Zhang,Yier Lin,Hongzhi Wang

DOI: https://doi.org/10.1016/j.engfailanal.2022.106138

IF: 4

2022-05-01

Engineering Failure Analysis

Abstract:In this paper, the bench test spectrum of charge air cooler of Semi-trailer truck, which is the bench test method of Charge Air Cooler reliability durability, and has the correlation with customer, is studied. Affecting CAC B10 life, thermal mechanical fatigue, gas pulse pressure fatigue and vibration fatigue are the main failure modes on the market. According to the principle that the users’ damage is equal to the bench damage in the laboratory, the durability assessment test method of Charge Air Cooler on the bench in the laboratory is established. By collecting the fleet data of the user groups, the target driving path covering 95% of the actual use intensity of vehicle users is determined. The field load spectrum on the target driving path is collected, the fatigue damage is calculated and comparing it with the damage of the test bench in the laboratory, and the relevant bench test spectrum of the Charge Air Cooler of semi-trailer truck with B10 life is formulated. The practical application results show that this method can accurately predict the potential failures of the Charge Air Cooler of semi-trailer truck. And product development cycle is effectively shortened.

engineering, mechanical,materials science, characterization & testing
Characterization of Contact Resistance Between Pantograph and Catenary System

WANG Wan-gang,WU Guang-ning,GAO Guo-qiang,WANG Bo,CUI Yi,LI Tian-zhi,YANG Ming-ming

2012-01-01

Journal of Central South University

Abstract:The static and dynamic contact resistance was studied with different contact pressures and traction currents. The results show that the static contact resistance of pantograph and centenary is decreased when contact pressure and traction current increases, and the dynamic contact resistance increases then decreases and at last increases with the increase of the locomotive speed at the same contact pressure and traction current. This causes two extremum points to contact resistance, which shows that there exist best matching among contact force, the locomotive speed and traction current.
Numerical Simulation of the Performance Characteristics of the Hybrid Closed Circuit Cooling Tower

M. M. A. Sarker,E. Kim,G. C. Moon,J. I. Yoon

DOI: https://doi.org/10.15388/na.2008.13.1.14591

2008-01-25

Abstract:The performance characteristics of the Hybrid Closed Circuit Cooling Tower (HCCCT) have been investigated applying computational fluid dynamics (CFD). Widely reported CFD techniques are applied to simulate the air-water two phase flow inside the HCCCT. The pressure drop and the cooling capacity were investigated from several perspectives. Three different transverse pitches were tested and found that a pitch of 45 mm had lower pressure drop. The CFD simulation indicated that when air is supplied from the side wall of the HCCCT, the pressure drop can be over predicted and the cooling capacity can be under predicted mainly due to the non-uniform air flow distribution across the coil bank. The cooling capacity in wet mode have been calculated with respect to wet-bulb temperature (WBT) and cooling water to air mass flow rates for different spray water volume flow rates and the results were compared to the experimental measurement and found to conform well for the air supply from the bottom end. The differences of the cooling capacity and pressure drop in between the CFD simulation and experimental measurement in hybrid mode were less than 5 % and 7 % respectively for the uniform air flow distribution.

mathematics, applied, interdisciplinary applications,mechanics

Study of 2500 Units PCTC Resistance Performance with Experiment and CFD Calculation Method

Study on the Resistance of a Large Pure Car Truck Carrier with Bulbous Bow and Transom Stern

A Study on Heat Transfer Model for the Dynamic Contact Boundary Between Piston Ring and Cylinder Liner

Simulation and Analysis Method for the Operation Characteristics of CIT400 High-Speed Comprehensive Inspection Train Based on Predictive Current Control

A method for ship resistance prediction based on CFD computation

Design of Medium and Large Size Pure Car and Truck Carriers

Effects of External Perturbations on Dynamic Performance of Carbon Dioxide Transcritical Power Cycles for Truck Engine Waste Heat Recovery

Analysis on Automobile Coasting Resistance

A Combined Computational Fluid Dynamics and Thermal–Hydraulic Modeling Approach for Improving the Thermal Performance of Corrugated Tank Transformers: A Comparative Study

Models Used in V-I Measuring Curve of PTCR

Comparative Study of 1800 V and 2400 V MCT and IGBT

Comprehensive Physical Commutation Characteristic Analysis and Test of Hybrid Line Commutated Converter Based on Physics Compact Model of IGCT

Numerical and Experimental Study on Flow and Heat Transfer Performance of Some Compact Surface Recuperators

Study on Dynamic Thermal Control Performance of Positive Temperature Coefficient (PTC) Material Based on a Novel Heat Transfer Model Considering Internal Heat Transfer

Numerical Investigation on Handling Stability of a Heavy Tractor Semi-Trailer under Crosswind

Research of Resistance Estimation Method for High-Speed Catamaran

The Study of Arc Rate, Friction, and Wear Performance of C/C Composites in Pantograph–Catenary System

Study of Resistance Performance of Vessels with Notches by Experimental and Computational Fluid Dynamics Calculation Methods

Study of customer correlation bench test spectrum of charge air cooler of semi-trailer truck

Characterization of Contact Resistance Between Pantograph and Catenary System

Numerical Simulation of the Performance Characteristics of the Hybrid Closed Circuit Cooling Tower