Design of a Quality DC Switching Power Supply

赵涛,王相綦,尚雷,王琳,张海燕

DOI: https://doi.org/10.3321/j.issn:0253-3219.2004.09.002

2004-01-01

Abstract:Based on the small-signal model of a phase-shifted full bridge DC/DC converter, analysis is made on the performance of a voltage regulating power supply in frequency domain. Experimental results are presented from a prototype.

What problem does this paper attempt to address?

Research on the Current-fed Phase Shift Full Bridge DC/DC Converter

Dehong Xu

2007-01-01

Abstract:The startup procedure of the current-fed phase shift full bridge (PSFB) zero current switching (ZCS) DC/DC converter is analyzed. The experiment results which satisfy the requirement of the ZCS DC/DC converter are also given at the end.
Design and implementation of off-line switching power-supply controller

苑婷,何乐年,柯徐刚

DOI: https://doi.org/10.3785/j.issn.1008973x.2010.11.015

2010-01-01

Abstract:A design method of an off-line switching power-supply controller with properties of high-efficiency and low-power is presented to improve performances of off-line power supplies. The controller was designed on basis of pulse-width modulation (PWM) mode and pulse skipping modulation (PSM) mode. The design method of the controller loop is based on the peak current mode. The controller operates in PWM mode, when the feedback voltage is less than 4.75 V, and works in PSM mode otherwise, ensuring high efficiency. Additional functions, such as short-circuit protection, over-voltage protection, under-voltage lockout, internal slope compensation, leading-edge blanking on current sense are included. For reducing the electromagnetic interference (EMI), the switching frequency is designed to be randomized within the range of 1 kHz at around centre frequency to flatten the power spectral density (PSD). The chip was implemented by using TSMC's 0.6 μm 40 V high voltage BCD process. Simulation results indicate that the controller realizes the required working modes and performs seamless switching between the modes. The controller can be applied to Li-Ion battery charger with a wide range of AC input (85~264 V) or power adapter.
A Family of PWM Plus Phase-Shift Bidirectional DC-DC Converters

HF Fan,DH Xu

DOI: https://doi.org/10.1109/pesc.2004.1355677

2004-01-01

Abstract:PWM is introduced to phase-shift bidirectional DC-DC converters, which can reduce current stresses, conduction loss and switching loss of semiconductors and can expand ZVS range. A technique to synthesize PWM plus phase-shift bidirectional DC-DC converter topologies is presented. Theoretical analysis, simulation and experimental results of one particular converter taken as an example, are provided in this paper.
Soft switching characteristics of a novel and efficient DC/DC converter

LIU Guo-qiang,PANG Jin-yong,XIE Yu,WANG Zheng-shi,SU Xiu-rong

DOI: https://doi.org/10.3969/j.issn.1001-4551.2013.05.022

2013-01-01

Abstract:Aiming at solving the problems of magnetic bias that may exist,large current stress,poor soft switching performance and duty cycle loss of phase-shift full-bridge circuit,a novel circuit topology that combines Boost circuit,phase-shift full-bridge circuit and resonant circuit was proposed.The working principles of the circuit were described firstly,and then the key waveform diagram of the circuit was given.A detailed study focusing on the conditions to achieve soft switching on the basis of working status and mathematical models with fundamental component method was made,and the design method to realize the soft switching of the novel DC/DC converter was given.The existing problems were studied and solutions were proposed.A 1 000 W prototype was developed.The experimental results indicate that the converter has a good performance,and verifies the correctness of the analysis and calculation.
Design of a Power Supply Module for Electric Vehicle Charging Station

ZHANG Zhi-quan,YAN Gang-feng

DOI: https://doi.org/10.3969/j.issn.1002-087x.2013.02.028

2013-01-01

Abstract:The principle of phase shift controlled full-bridge(FB)converter was analyzed,and a reliable IGBT driver circuit was presented.Based on the above,a power supply module with constant voltage or constant current output was designed for electric vehicle charging.Differential voltage feedback made it possible to achieve series and parallel.Finally,a prototype was developed with three-phase AC 380 V input,DC 100 V output,10 kW output power.The experimental results show that the power supply has good control performance,strong flexibility and reliability.
Design of Voltage-mode Phase-shift Full Bridge Soft Switching DC/DC Converter Based on UCC3895

Xiangning He

2006-01-01

Abstract:A high frequency DC/DC power converter is presented.The control strategy of this converter is woltage-mode phase-shift PWM control.And it achieves zero voltage switching(ZVS)at a wide variety of loads and small turns ratio.At last,the experiment results anti waveforms are presented and expounded in detail.
Design of Phase-shifted Full-bridge DC/DC Converter Based on Digital Control with TMS320F28027

WU Hong-xue,YANG Wei,YANG Shi-yan

DOI: https://doi.org/10.13234/j.issn.2095-2805.2012.4.24

2012-01-01

Abstract:The digital control is the development trend of future power supply. A ZVS phase-shifted full-bridge PWM controlled DC/DC converter in peak current control mode was designed using TI’s digital power control chip TMS320F28027. The main circuit of phase-shifted full-bridge converter was designed adding the clamping diode and resonant inductance in primary side, the working principle of inhibiting voltage spikes of the output rectifier was described. The model of the control system in peak current mode was built and the simulation in Matlab / Simulink environment was achieved. A 1.2kW prototype was presented. Simulation and experimental results show that the design of the power supply is feasible.
System study and design of a switched capacitor DC-DC converter

SHAO Bin,YANG Yu-jia,WANG Ying,HONG Zhi-liang

DOI: https://doi.org/10.3969/j.issn.1007-0249.2008.04.026

2008-01-01

Abstract:The steady state and dynamic performance of a switched capacitor DC-DC converter are analyzed by the state space equation set. The DC-DC converter is based on a multi-stage switched capacitor charge pump structure with subsection conversion ratio. Optimal methods are also presented on system control methodology (current control and pulse frequency modulation) and frequency compensation. By using those optimal methods, a switched capacitor DC-DC converter with high efficiency, low output ripple and low cost is realized, the transistor-level simulation results meet the power management chip requirements of the portable electronic devices.
A novel current-feed soft-switching two-switch forward resonant DC-DC Transformer (DCX)

Wei Qin,Bo Zhu,Xu Zhang,Xinke Wu

DOI: https://doi.org/10.1109/PEAC.2014.7037841

2014-01-01

Abstract:In this paper, a current-feed resonant two-switch forward DC-DC Transformer (DCX) is proposed for high-efficiency and high-density unregulated bus converter applications. With a resonant capacitor in series with the leakage inductance of the transformer, ZCS turn-on and nearly ZCS turn-off can be achieved for the primary switches and there is no body diode and reverse recovery losses in the SR. Meanwhile, the magnetizing current is used to achieve ZVS turn-off for the primary switches. The circuit operating principle and design considerations are discussed. An 110W prototype is built up to verify the theoretical analysis.
Modeling, Analysis and Design of 15kw Zero-Voltage Zero-Current Switched Full Bridge PWM Converter

Yimeng Shi,Guozhu Chen,Yulin Li

DOI: https://doi.org/10.1109/iecon.2007.4460260

2007-01-01

Abstract:This paper presents the modeling and design of a novel ZVZC FB-PWM converter. Compared to the traditional topology which employs a saturated inductor to block, the reverse current in order to achieve ZCS for the lagging leg, a novel one using two diodes in series with the lagging leg is adopted. Both the duty ratio loss is reduced and the efficiency is improved, which further reliefs the problem of thermal handling caused by the saturated inductor. What's more, better stability and dynamic behavior are acquired. A complete small-signal model for the novel ZVZC FB-PWM converter is developed. Validation of design of equation and model prediction is accomplished through numerical solutions of steady-state nonlinear equations and experimental results of a 15 kW module converter operating at 20 kHz.
Sampled-Data Control with Adjustable Switching Frequency for DC–DC Converters

Xingda Yan,Zhan Shu,Suleiman M. Sharkh,Zheng-Guang Wu,Michael Z. Q. Chen

DOI: https://doi.org/10.1109/tie.2018.2878116

IF: 7.7

2018-01-01

IEEE Transactions on Industrial Electronics

Abstract:In this paper, a novel sampled-data control approach is proposed for dc-dc converters. The dc-dc power electronic converter is modeled as a sampled-data switched affine system according to the status of the power switch. A novel switching control algorithm is synthesized by using the switched Lyapunov theory. The proposed approach is able to not only drive the output to a prescribed set point from any initial condition, but also track a varying reference signal, and the switching frequency can be adjusted online with the guaranteed stability. In addition, with this approach, continuous conduction mode and discontinuous conduction mode operations can be treated in a unified way. The effectiveness and merits of the proposed method are illustrated by experiments on a laboratory prototype.
Design of high efficiency dc switching power supply based on soft switch

Hao Wu,Linyan Xiao

DOI: https://doi.org/10.1088/1742-6596/1345/5/052077

2019-11-01

Journal of Physics: Conference Series

Abstract:Abstract At present, due to the small size, high power density, high efficiency, a variety of switching power supply is getting more and more widely used. With the improvement of automation degree of power system, especially the microcomputer of protection device, the program control of communication device and the requirement of power efficiency are also increasing. In order to solve the problem of high power consumption and unstable output of linear circuit in the process of energy conversion, this paper proposes a stable switching power supply based on SG3525 control. The constant voltage source USES PWM control principle to control the duty ratio of the switch tube to achieve the output voltage of 24V. Since the switch power supply design is usually based on the ideal state of the device, SABER simulation software is used to verify the feasibility of the circuit. At the same time, through physical verification, the circuit performance when the input voltage fluctuates. And test the load capacity and work efficiency of the circuit.
A ZVS DC-DC Converter Using Non-Dissipative Snubber Circuit

Tiecheng Sun,Jianhui Guo,Rui Li,Lei Fu

DOI: https://doi.org/10.1109/vppc.2008.4677770

2008-01-01

Abstract:Based on the characteristics of conventional full-bridge phase-shift PWM ZVS (zero-voltage-switching) DC-DC converter, a novel full-bridge phase-shift PWM ZVS DC-DC converter using non-dissipative snubber circuit is proposed. The converter can achieve ZVS for all switches effectively. The principle and operation modes of the converter are analyzed in detail, and the necessary condition of soft switching is also analyzed. The digital control system of the converter is designed base on TMS32OF2812 DSP. The proposed theory has been verified on a 24V/2A, 100 kHz experimental converter. The soft switching of leading and lagging legs can be achieved in wide load rang.
Dynamic Modeling and Minimum Backflow Power Controlling of the Bi-Directional Full-Bridge DC-DC Converters Based on Dual-Phase-Shifting Control

Cheng Hong,Gao Qiaomei,Zhu Jinbiao,Yang Xiaokang,Wang Cong

DOI: https://doi.org/10.3969/j.issn.1000-6753.2014.03.031

2014-01-01

Abstract:The soft-switching conditions and the power transmission characteristics of bi- directional full-bridge DC-DC converter based on dual-phase-shifting control are analyzed．The dual-phase-shifting control strategy with the minimum backflow power under ZVS soft-switching conditions are proposed. Based on the averaged modeling method, a small-signal model with the dual-phase-shifting control of the bi-directional full-bridge DC-DC converter is presented. At last,based on an experimental prototype, the effectiveness of the models and proposed control strategy are validated by experiments in both transient and steady state operations, and experimental results also verify the effectiveness of the proposed control strategy to improve the efficiency of the converter.
Design and comparison of two front-end Dc/Dc converters: LLC resonant converter and soft-switched phase-shifted full-bridge converter with primary-side energy storage inductor

Zhao Chen,Wu Xinke,Qian Zhaoming

DOI: https://doi.org/10.1109/APEC.2009.4802796

2009-01-01

Abstract:This paper presents detailed design and comparison of two front-end Dc/Dc converters which are suitable especially for the medium-power level applications with low output voltage and high output current both. Where, the LLC resonant converter drawn more and more attention recently shows its essential advantages in high conversion efficiency and high power density. However, due to the variable-frequency control strategy, its slow response especially in burst-mode with light-load or null-load makes the design more difficult. On the oppose side, the soft-switched Phase-Shift (PS) Full-bridge (FB) converter with primary-side energy storage inductor proposed in the foregoing work can be operated in CCM, BCM and DCM respectively according to the different designs. Where, the optimum design consideration indicates that the BCM and DCM operation modes can help to obtain high conversion efficiency. Additionally, thanks to the conventional phase-shift control strategy, it can obtain fast response during the burst-mode with light/null load. Finally, two lab-made prototypes of these two Dc/Dc converters (300 Watts, 100 kHz) are built up to verify the theoretical analysis and comparison.
System Architecture Design and Research of a DC/DC Switch Mode Power Supply for Portable Electronics System

王海永,李永明,陈弘毅

DOI: https://doi.org/10.3969/j.issn.1000-3819.2002.02.008

2002-01-01

Abstract:This paper introduced the system architecture design of a DC/DC switch mode power supply,analyzed the method of system design for improving the efficiency of power supply convertion.Finally,this paper presented a system architechture of a DC/DC switch mode power supply,which is implemented in LSI chip.
Design of a 12kw PWM Converter with Phase Shift Control and Zero Voltage Switching

ZHANG Yong-feng,HUANG Zi-long,YANG Xu,WANG Zhao-an

DOI: https://doi.org/10.3969/j.issn.1000-100x.2006.04.019

IF: 5.967

2006-01-01

IEEE Transactions on Power Electronics

Abstract:The principle of Phase Shift Controlled Full-Bridge(FB) Zero-Voltage-Switching(ZVS) PWM Converter is ana-lyzed.Base on the simulation with the model of the system,the control parameters were gotten and the prototype of 12kW opera-tional power supply was implemented and tested.The experimental results shown that the design scheme is feasible.
Design of 12kW Phase-shifting Full-bridge Zero Voltage PWM Converter

Zhang Yongfeng,Huang Zilong,Yang Xu,Pei Yunqing,Wang Zhaoan

2006-01-01

Abstract:Based on analysis of the operating principle of phase-shifting full-bridge zero voltage PWM converter,a 12kW electric power supply was designed and tested. The simulation model of main circuit and control circuit of such a kind of power supply was built and the open-loop log frequency characteristics were obtained successfully. The simulation results shows that the design scheme is feasible and the high accuracy and dynamic characteristic of output voltage and current could meel design requirements completely.
Key Technologies for Novel Switching Power Supplies

罗萍,李强,熊富贵,武洁,牛全民,曾家玲,张波,李肇基

DOI: https://doi.org/10.3969/j.issn.1004-3365.2005.01.018

2005-01-01

Abstract:Key technologies for novel switching power supplies are presented. By combining pulse skip modulation mode with current limit state machine, and introducing fuzzy control theory and chaos theory, characteristics of the novel switching power supply, such as energy transfer efficiency, transient response, load regulation rate and anti-interference, have been greatly improved. Low EM characteristics could be realized utilizing frequency jitter technique. With the rapid advancement of the semiconductor switching power device, novel switching power supplies will become shorter, smaller, lighter, safer and more cost-effective in the future, achieving both high efficiency and high quality.
A DESIGN OF DISCRETE COMPONENTS BASED INTEGRATED POWER MODULES

陈文洁,杨旭,杨拴科,王兆安

DOI: https://doi.org/10.3321/j.issn:0258-8013.2003.12.021

2003-01-01

Abstract:A design scheme of integrated power modules for switched mode power supplies based on discrete devices is presented in the paper, including 2 types of modules for soft switching power factor correction circuit and phase shifted full bridge soft switching circuit. Power switches and some driving components are integrated in the modules. A multilayer structure is adopted resulting in compact circuit layout and reduced parasitic parameters, the voltage and current stresses on switches as well as the EMI of the circuit are significantly reduced. The modules have lower thermal resistance and higher reliability due to their double side heat dissipitation features. Full load experiments have been carried out to validate the design and evaluate its performances.

Design of a Quality DC Switching Power Supply

Research on the Current-fed Phase Shift Full Bridge DC/DC Converter

Design and implementation of off-line switching power-supply controller

A Family of PWM Plus Phase-Shift Bidirectional DC-DC Converters

Soft switching characteristics of a novel and efficient DC/DC converter

Design of a Power Supply Module for Electric Vehicle Charging Station

Design of Voltage-mode Phase-shift Full Bridge Soft Switching DC/DC Converter Based on UCC3895

Design of Phase-shifted Full-bridge DC/DC Converter Based on Digital Control with TMS320F28027

System study and design of a switched capacitor DC-DC converter

A novel current-feed soft-switching two-switch forward resonant DC-DC Transformer (DCX)

Modeling, Analysis and Design of 15kw Zero-Voltage Zero-Current Switched Full Bridge PWM Converter

Sampled-Data Control with Adjustable Switching Frequency for DC–DC Converters

Design of high efficiency dc switching power supply based on soft switch

A ZVS DC-DC Converter Using Non-Dissipative Snubber Circuit

Dynamic Modeling and Minimum Backflow Power Controlling of the Bi-Directional Full-Bridge DC-DC Converters Based on Dual-Phase-Shifting Control

Design and comparison of two front-end Dc/Dc converters: LLC resonant converter and soft-switched phase-shifted full-bridge converter with primary-side energy storage inductor

System Architecture Design and Research of a DC/DC Switch Mode Power Supply for Portable Electronics System

Design of a 12kw PWM Converter with Phase Shift Control and Zero Voltage Switching

Design of 12kW Phase-shifting Full-bridge Zero Voltage PWM Converter

Key Technologies for Novel Switching Power Supplies

A DESIGN OF DISCRETE COMPONENTS BASED INTEGRATED POWER MODULES