Abstract:As a step towards developing a finite element model of the knee that can be used to study how the variables associated with a meniscal replacement affect tibio-femoral contact, the goals of this study were 1) to develop a geometrically accurate three-dimensional solid model of the knee joint with special attention given to the menisci and articular cartilage, 2) to determine to what extent bony deformations affect contact behavior, and 3) to determine whether constraining rotations other than flexion/extension affects the contact behavior of the joint during compressive loading. The model included both the cortical and trabecular bone of the femur and tibia, articular cartilage of the femoral condyles and tibial plateau, both the medial and lateral menisci with their horn attachments, the transverse ligament, the anterior cruciate ligament, and the medial collateral ligament. The solid models for the menisci and articular cartilage were created from surface scans provided by a noncontacting, laser-based, three-dimensional coordinate digitizing system with an root mean squared error (RMSE) of less than 8 microns. Solid models of both the tibia and femur were created from CT images, except for the most proximal surface of the tibia and most distal surface of the femur which were created with the three-dimensional coordinate digitizing system. The constitutive relation of the menisci treated the tissue as transversely isotropic and linearly elastic. Under the application of an 800 N compressive load at 0 degrees of flexion, six contact variables in each compartment (ie., medial and lateral) were computed including maximum pressure, mean pressure, contact area, total contact force, and coordinates of the center of pressure. Convergence of the finite element solution was studied using three mesh sizes ranging from an average element size of 5 mm by 5 mm to 1 mm by 1 mm. The solution was considered converged for an average element size of 2 mm by 2 mm. Using this mesh size, finite element solutions for rigid versus deformable bones indicated that none of the contact variables changed by more than 2% when the femur and tibia were treated as rigid. However, differences in contact variables as large as 19% occurred when rotations other than flexion/extension were constrained. The largest difference was in the maximum pressure. Among the principal conclusions of the study are that accurate finite element solutions of tibio-femoral contact behavior can be obtained by treating the bones as rigid. However, unrealistic constraints on rotations other than flexion/extension can result in relatively large errors in contact variables.

Determination of common contact area and its use of the femur prosthesis design on the femoral condylar facet which patellofemoral and tibiofemoral joint sliding Patellofemoral and Tibiofemoral Joint Sliding

Geometric Characters of Distal Femur and Knee Prosthesis Design

Influence of Congruency Design on the Contact Stress of a Novel Hinged Knee Prosthesis Using Finite Element Analysis

The influence of patellofemoral joint contact geometry on the modeling of three dimensional patellofemoral joint forces

Measurement of femoral posterior condylar offset and posterior tibial slope in normal knees based on 3D reconstruction

A method for estimating the contact area of a dual-mobility total hip prosthesis

Patellofemoral Joint Contact Area Quantified In Vivo During Daily Activities

Stress Analysis and Shape Design of a Femoral Hip Prosthesis

Analysis of Finite Element Modeling on Elasto-Plasticity of Polyethylene Liner under Contact Stress after THA

Articular contact motion at the knee during daily activities

Tuberosity reconstruction baseplate for shoulder hemiarthroplasty: Morphological design and biomaterial application

Relationship Between Patellofemoral Finite Helical Axis and Femoral Trans-Epicondylar Axis Using a Static Magnetic Resonance-Based Methodology

Shape Design of Femoral Hip Prosthesis

Effect of Tibial Rotation on the Contact Pressure and Contact Area of Patello-femoral Joint

Using Virtual Markers To Explore Kinematics Of Articular Bearing Surfaces Of Knee Joints

A finite element model of the human knee joint for the study of tibio-femoral contact

Reconstruction and application of three-dimensional quasi-dynamic motion model of patellofemoral joint

An MRI-Based Correlation Study Investigating the Effect of Varying Posterior Femoral Condyle Angles on the Patellofemoral Joint

Contact area and pressure changes of patellofemoral joint during stair ascent and stair descent

Analysis of in-vivo articular cartilage contact surface of the knee during a step-up motion.

Femoral coordinate system based on articular surfaces: Implications for computer-assisted knee arthroplasty