Abstract:The geometric parameters of the deposited layer include the width, height, and penetration depth of the deposited layer. The welding current, wire feeding speed, and torch travel speed during the additive manufacturing process of TC4 titanium alloy have the greatest impact on the geometric parameters of the deposited layer. In order to study how the deposition layer width, deposition layer height, and penetration depth are affected by the welding current, wire feeding speed, and torch travel speed, this article uses Design Expert 8.0.6 software for Box−Behnken design response surface experiments. During the experimental design, the welding current, wire feeding speed, and torch travel speed are used as input variables. The deposition layer width, deposition layer height, and penetration depth are selected as the responses. We designed 17 response surface experiments that were conducted using GTAW-AM. The results show that as the welding current increases, the penetration depth and width of deposition layer gradually increase, and the deposition layer height gradually decreases. As the wire feeding speed increases, the deposition layer height and penetration depth gradually increase, and the wire feeding speed has a minimal effect on the deposition layer width. As the torch travel speed increases, the penetration depth, width and height of deposition layer gradually decrease. The response surface method experimental design can also optimize the matching of three process parameters: welding current, wire feeding speed, and torch travel speed, thereby obtaining the optimal matching range of process parameters. Within the optimized matching range of process parameters, a welding current of 90 A, a wire feeding speed of 900 mm/min, and a torch travel speed of 200.18 mm/min were selected to prepare TC4 titanium alloy thin-walled part. The microstructure of the top, middle and bottom are all basketweave structure. The α phase gradually becomes coarse from the top to the bottom. The microhardness of the top, middle, and bottom of the thin-walled parts is 362.7 HV, 352.7 HV, and 340.5 HV, respectively. The horizontal tensile strength is 926.1 MPa, with an elongation of 12.22%, and the vertical tensile strength is 938.1 MPa, with an elongation of 14.41%.

Study On The Influence Of Contact Glue Layer Growth Condition On The Quality Of Gap Fill Tungsten Layer

Influence of Surface Morphology and Microstructure on Performance of CVD Tungsten Coating under Fusion Transient Thermal Loads

Investigation Of Tungsten Rich Residue Defects Induced By Electron Beam Inspection Post Contact Tungsten Chemical And Mechanical Polish

Enhanced electroless Ni-P plating quality on binderless tungsten carbide by atmospheric pressure plasma pretreatment

Impact of Film Morphology on Chemical Mechanical Polishing of Tungsten

Evolution of Chemical, Structural, and Mechanical Properties of Titanium Nitride Films with Different Thicknesses Fabricated Using Pulsed DC Magnetron Sputtering

EFFECT OF C2H2 FLOW RATE ON THE DEPOSITION OF TI-TIC-TIC/DLC GRADIENT NANO-COMPOSITE FILM ON NITI ALLOY

Tungsten Contact and Line Resistance Reduction with Advanced Pulsed Nucleation Layer and Low Resistivity Tungsten Treatment

Electrical and Mechanical Characterization of Chemical Vapor Deposition of Tungsten on Sputter-Deposited TiN Layers

Effects of Heater Surface Precoating and Plasma Treatment on Deposited TiN Film Thickness

Effects of profiles and conditioning methods of heater surfaces on deposited TiN film thickness and uniformity

The Microstructure and Tribological Behavior of Ultrasonic Electroless Ni-P Plating on TC4 Titanium Alloy with Heat-Treatment

Experimental and Numerical Studies of Tungsten Line Growth in Laser Chemical Vapor Deposition

Microstructure-based crack formation in tungsten exposed to cyclic transient heating

Thickness uniformity, electrical properties, and stress of sputtered TiN thin films

Microstructural Effects of Y2O3 and TiC Additions in Tungsten

Optimization of Process Parameters on Surface Integrity in Wire Electrical Discharge Machining of Tungsten Tool YG15

Interface defects and stress relief of super hard Ti+C/a-CN x gradient multilayer films

Study on the Relationship between Process Parameters and theFormation of GTAW Additive Manufacturing of TC4 Titanium Alloy Using the Response Surface Method

Effect of Surface Pre-Treatment on the Adhesion between HiPIMS Thick Cu:CuCNx Coating and WC-Co Shim

Wear of mold surfaces: Interfacial adhesion in precision glass molding