Abstract:Carbon nanospheres were covalently modified with hydroxy-terminated poly(dimethylsiloxane) to give a new sorbent (referred to as CNS-PDMS). It was applied as the extraction phase in a sol–gel based solid-phase microextraction fiber for benzene, toluene, ethylbenzene and o-xylene (BTEX). Due to the unique properties of CNS and the performance of the sol–gel coating technology, this fiber possesses a porous surface, a long operational lifespan (at least 200 times), and high thermal stability (up to 350°C). Its extraction capability is higher than that of commercial polydimethylsiloxane (PDMS) and polydimethylsiloxane/divinylbenzene (PDMS/DVB) fibers. Following desorption, the BTEX were quantified by GC with FID detection. The detection limits (at an S/N ratio of 3) range from 1 to 10 pg mL−1, and the limits of quantification (at an SNR of 10) are between 3 and 30 pg mL−1. The repeatability of a single fiber (for n = 5) is between 3.9 and 6.3%, and the fiber-to-fiber reproducibility (for n = 3) ranges from 5.3 to 8.2%, respectively. The relative recoveries in the real water samples ranged from 92.5% to 99.5%. The results demonstrate that the method is highly effective for analyzing BTEX in water samples.Graphical abstractA new method is described for the microextraction of benzene, toluene, ethylbenzene and o-xylene (BTEX). Poly(dimethylsiloxane) grafted carbon nanospheres were used as extraction phase to prepare a sol–gel SPME fiber. This method has a low LOD and a relatively wide linear range.

Investigation of a Novel Activated Carbon Coating Fiber Used for Solid Phase Micro-Extraction

Preparation and Characteristics of New Coating for Solid-Phase Microextraction.

Preparation of a Novel Activated Carbon Coating Fiber for Solid Phase Micro-Extraction and Its Application for Halocarbon Compound Analysis in Water

Preparation of a Carbon-Coated SPME Fiber and Application to the Analysis of BTEX and Halocarbons in Water

Preparation and Application of Poly(dimethylsiloxane)/β‐cyclodextrin Solid‐phase Microextraction Fibers

Preparation and Characterization of Porous Carbon Material-Coated Solid-Phase Microextraction Metal Fibers.

Evaluation of the solid-phase microextraction fiber coated with single walled carbon nanotubes for the determination of benzene, toluene, ethylbenzene, xylenes in aqueous samples.

Preparation and Investigation of Solid Phase Microextraction Complex Coating of Phenylethylenethyl Acrylate Copolymer and Polymethylsiloxane

Cnt-Tio2 Coating Bonded Onto Stainless Steel Wire As A Novel Solid-Phase Microextraction Fiber

Adjusted active carbon fibers for solid phase microextraction.

Carbon nanospheres covalently modified with polydimethylsiloxane on a porous sol–gel support for use in headspace solid-phase fiber microextraction of BTEX

Preparation and Characterization of Metal-Organic Framework MIL-101(Cr)-coated Solid-Phase Microextraction Fiber

Preparation and characterization of vinyl-functionalized mesoporous organosilica-coated solid-phase microextraction fiber

A solid-phase microextraction fiber with carbon nanoparticles as sorbent material prepared by a simple flame-based preparation process

PDMS-coated Γcd-Mof Solid-Phase Microextraction Fiber for BTEX Analysis with Boosted Performances.

Solid-Phase Microextraction Fibers Based on Novel Materials: Preparation and Application

DETECTION OF ORGANIC SUBSTANCES IN WATER BY SOLID-PHASE MICRO-EXTRACTION WITH ACTIVE CARBON COATED EXTRACTOR

Incorporation of Carbon Nanotubes into Graphene for Highly Efficient Solid-Phase Microextraction of Benzene Homologues

Graphitic Carbon Nitride Derivative with Large Mesopores As Sorbent for Solid-Phase Microextraction of Polycyclic Aromatic Hydrocarbons.

Fabrication of OMC modified SPME fiber and study of its extraction performance

[Advances in the Fiber Coating of Solid Phase Micro-Extraction].