Abstract:The technique of Isotope Ratio Mass Spectrometry(IRMS)is the gold standard of accurate and precise analyses for all sorts of isotopic relative abundance amongst analytical techniques. In many fields, the extensive application of continuous flow IRMS not only improves effective runs, but also reduces sample size as well as enhancing sensitivity. However, for the purpose of obtaining more accurate results, which can be compared between different laboratories, it is imperative to have good strategies and protocols in the run, monitoring of routine analytical performance and quality. In addition, detailed calibration for the raw data is highly desirable. In order to obtain reliable data by using IRMS coupled with EA (TC/EA), requirements need to be met as follows: (1) instrument set-up and environmental control, measurement preparation, sample preparation and weight, reference materials utilization and selection, sequence etc; (2) strictly calibrated systems including tuning sensitivity and linearity, monitoring the background, stability detection, H3+ correction; (3) reliable data reduction. The strategies of calibrating, normalization and control linear by using reference materials are discriminated in different labs. So it is expected to have a unified data-processing programme. Two-point normalization (or multi-point normalization) is the best executive program at present. If two different reference materials are used four times for normalization, or four different reference materials are used two times for each batch of samples, this may reduce the normalization uncertainty by 50%. The modern IRMS is capable of measuring natural isotope ratio variations with an uncertainty better than 0.02. Nevertheless, it is a challenge to the use of reference materials with the cover range of unknown isotopes, especially for H isotope absence of the standard materials and poor precision (an order of magnitude lower compared with carbon, nitrogen, oxygen isotope). This paper aims to highlight general principles of IRMS coupled to an EA or a TC/EA and the practices of analytical application of stable isotope ratio measurement. The knowledge on the protocols of continuous flow IRMS analyses is necessary for the acquisition of reasonable accuracy and precision for stable isotope composition.

The Real Time Weighting Method Used for Determining Reference Value of Intercomparison

The use of actual water samples for laboratory comparison between the results of evaluation and analysis

Comparison Study on Rare Earth Radioanalysis

Investigations of reactivity worth measurement in a fast neutron reactor with the inverse kinetics method

INTERCOMPARISON EXPERIMENT AND UNCERTAINTY ANALYSIS OF THREE MEASUREMENT METHODS FOR RADON PROGENY AT NIM.

Decay/Ingrowth Uncertainty Correction Of Po-210/Pb-210 In Seawater

Detection of Inconsistencies in Isotope Ratios Certified in the Isotopic Primary Standards for Copper, Zinc and Nickel

Optimized Method for Individual Radon Progeny Measurement Based on Alpha Spectrometry Following the Wicke Method

Process‐Based Intercomparison of Water Isotope‐Enabled Models and Reanalysis Nudging Effects

Interlaboratory comparison of gross alpha/beta activity of drinking water over a decade

A Novel Method for Gamma Spectrum Analysis of Low-Level and Intermediate-Level Radioactive Waste

Test and comparison of aerosol sample preparation methods in radiation monitoring

Decay/ingrowth Uncertainty Correction of (210)po/(210)pb in Seawater.

Preliminary Study on Aerosol Particle Addition Calibration Method for On-Line Quantitative Analysis of Airborne Radioactive Particles with Icp-Ms

THE INTERCOMPARISON OF MASS OF ~(238)U FISSION DEPOSITS

Optimization of analytical conditions for precise and accurate isotope analyses of Li, Mg, Fe, Cu, and Zn by MC-ICPMS

Results of a European interlaboratory comparison on gross alpha/beta activity determination in drinking water

Application of Mean Value Theorem of Integrals in the Efficiency Callibration Technology of Radioactive Xeon Sample

Data Normalization and Quality Control of Light Element Stable Isotope Analyses by Means of Continuous Flow Isotope Ratio Mass Spectrometry

Toward a New Primary Standardization of Radionuclide Massic Activity Using Microcalorimetry and Quantitative Milligram-Scale Samples

Application of some calibration strategies in comparison to determine Cr, Ni, Cu, Zn, As, and Pb in contaminated plants by wavelength dispersive x‐ray fluorescence