Abstract:Experimental study of air natural convection in horizontally-positioned copper metallic foams with open cells was conducted. Temperature distributions on the heating surface were tested under different heating power for foam samples having different porosities and pore densities. The effects of porosity and pore density on the total thermal resistance of the foam sample were quantified. It is found that the porous surface can enhance the natural convection and reduce the thermal resistance by about 20% in comparison with a smooth surface. The surface area density and mass flow rate in natural convection are affected by porosity and pore density simultaneously. When the porosity is relative small (ε = 90%), there exits a critical value of the Gr number (turning point) for two pore densities (10ppi and 40ppi). When the Gr number is less than this critical value, the foam with a higher pore density has the lower total thermal resistance, whereas when the Gr number exceeds the turning point value, the opposite holds. If the porosity is increased to ε = 95%, the foam with a higher pore density has the lower thermal resistance in the whole experimental range. When the porosity and pore density is the same, the foam with smaller size has the higher thermal resistance in the whole experimental range. If the size is relatively small (10010050mm), for the two pore densities studied (20ppi and 80ppi), there exits a critical value of the Gr number (turning point). The foam with a lower porosity(ε = 90%) has the lower thermal resistance and the decrease is more obvious for the case of 80ppi.If the size is relatively big(10010080mm),there exists a critical value of the Gr number (turning point) only for the case of 10ppi. When the Gr number is less than this critical value, the foam with a higher porosity (ε = 95%) has the higher total thermal resistance, the opposite holds. While for the other two pore densities (20ppi and 40ppi), there is no turning point. The foam with a higher porosity (ε = 95%) has the higher total thermal resistance in the whole experimental range. © 2011 IEEE.

Material effect on pool boiling heat transfer of open-celled metal foams with low pore density

ICOPE-15-C130 Investigation on Pool Boiling Heat Transfer of Metal Foams with Gradient Pore Densities

Experimental investigation on the influence of copper foam characteristics on pool boiling heat transfer

Influences of Nanoparticles on Pool Boiling Heat Transfer in Porous Metals

EXPERIMENTAL STUDY OF POOL BOILING ON SURFACE OF METAL FOAM WITH OPEN CELLS

Experimental study on pool boiling heat transfer in gradient metal foams

Pool boiling heat transfer of open-celled metal foams with V-shaped grooves for high pore densities

Experimental Study of Pool Boiling Heat Transfer on Horizontal Metallic Foam Surface with Crossing and Single-Directional V-shaped Groove in Saturated Water

Pool Boiling Heat Transfer on Open-Celled Metallic Foam Sintered Surface under Saturation Condition

Single-directional and crossing V-shaped groove effect on pool boiling heat transfer of metal foam with high pore density

Experimental study of natural convection in horizontally-positioned open-celled metal foams

Experimental Study of Natural Convective Heat Transfer in Horizontally-Positioned Cellular Metal Foams with Open Cells

On the effect of silver nanoparticles deposition on porous copper foams on pool boiling heat transfer enhancement: an experimental visualization

Experimental investigation of permeability and Darcy-Forchheimer flow transition in metal foam with high pore density

Experimental Study on Capillary Microflows in High Porosity Open-Cell Metal Foams

Effect of structural characteristics on the natural convective heat transfer performance of copper foam

Thickness Effect on Pool Boiling Heat Transfer of Trapezoid-Shaped Copper Foam Fins

Investigation of Bubble Behavior in Gradient Porous Media under Pool Boiling Conditions

Pool Boiling Heat Transfer of R134a on Single Horizontal Tube Surfaces Sintered with Open-Celled Copper Foam

Enhanced Boiling Heat Transfer by Gradient Porous Metals in Saturated Pure Water and Surfactant Solutions

Effect of copper foam thickness on pool boiling heat transfer of HFE-7100