Abstract:This study demonstrates the benefits of high-quality and high-efficiency supersonic flame spraying, aids smart decision-making, and lays a theoretical basis for the practical application of iron-based amorphous coatings. By implementing an artificial neural network, a comprehensive design study that considers several factors and levels may effectively direct the optimization of process parameters, improve product surface performance, minimize expenses, and boost efficiency. This enables the raw materials to attain maximum efficiency in real-world applications. This work examined the technological parameters and properties of Fe-based amorphous nanocrystalline coating using supersonic flame spraying technology, utilizing a multi-factor and multi-level design analysis approach to conduct experimental parameter design. A BP neural network model was developed to investigate the impact of coal oil quantity, oxygen quantity, powder feeding rate and spraying distance on the porosity, hardness, bonding strength, and deposition efficiency of the coating. The powder and coating's microstructures were analyzed using scanning electron microscopy and transmission electron microscopy. In addition, X-ray diffraction, synchronous thermal analysis, and other techniques were employed to observe and analyze the phase constitution and amorphous content of both the powder and the coating that was created. The computer simulation results were validated while optimizing the process parameters. The measurement of the ideal spraying process parameter range further improved the coating performance. The text discusses the mechanism of pore development at a microscopic level during spraying, as well as the connection between the formation principle of amorphous nanocrystalline and the coating performance. The results revealed that several components have mutual influence on the coating. Theoretically, the most favorable spray parameters for achieving optimal coating are as follows: a diesel flow rate of 23 L·h-1, oxygen flow rate of 51 L·h-1, a powder feeding rate of 72 g·min-1, and a spraying distance of 280 mm. To develop a high quality coating of Fe-based amorphous alloy that improves material surface performance, one must carefully select a suitable spraying material and employ the proper thermal spraying procedure. The coating yielded the following results: a thickness of 270 μm, a porosity of 1.3％, a binding strength of 80 MPa, and a hardness of 1110 HV0.3. The amorphousness degree of the coating was exhibited around 80％, with a nanocrystalline diameter was ranging from 3-5 nm. Crystallization of the coating is only possible above 600 ℃.

Study on the Property of NiCrFe-Cr2C3 Coating by Supersonic Arc Spraying

Study on the Properties of High Cr-Ni Alloy Coating by Supersonic Arc Spraying

Study on Microstructure and Properties of FeNiCr/Ni Coated Cr_3C_2 Coatings Deposited by High Velocity Arc Spraying

Study on Microstructure and Properties of Cr3C2/Fe Coating Prepared by Arc Spraying on Copper Surface

Phases and Structure Research of High Velocity Arc Spraying FeAlCrNi-Cr3C2 Coatings

Preparation process, surface properties and mechanistic study of HVAF-sprayed CoCrFeNiMo 0.2 high-entropy alloy coatings

Microstructure and Erosional Behavior of Erosion-Resistant Coatings of Super-Critical Boiler Pipes

Microstructure and Properties of FeMnCrAl/Ni Coated WC Coatings Deposited by High Velocity Arc Spraying

Microstructure and properties of high velocity arc sprayed FeMnCr/Cr_3C_2 coatings

Study on High Temperature Properties and Application of Cr3C2/Cr-Fe Coating

Mechanical, Tribological, and Oxidation Resistance Properties of NiCrAlY Coating by Atmospheric Plasma Spraying

Study on Properties of Coatings Prepared by Supersonic Plasma Spraying with Three Kinds of WC-12Co Powder

Investigation of microstructure and properties of AC-HVAF sprayed Ni-based coatings

Study on the Corrosive Resistance of New High Chromium Alloy and NiCrFe-Cr3C2 Arc-Sprayed Coating in High-Temperature

Properties of Fe-Based Cr3c2 Coatings Produced with A High-Velocity Arc-Spraying Process

Experimental Study on Spray Parameters and Properties of HVOF Sprayed Fe-based Amorphous Nanocrystalline Coating

Preparation and Performance of Ni-Al and 3cr13 Coatings on Carbon Steel by Arc Spraying for Boiler Heat Exchanger Pipelines: A Comparative Study

The Microstructure and Deposition Behavior of NiCr Alloy Coatings Using Laminar Plasma Spraying

Microstructure and Corrosion Behavior of (CoCrFeNi)95Nb5 High-Entropy Alloy Coating Fabricated by Plasma Spraying

Study on Structure and Properties of Plasma Spraying Fe-Ni-B Coating

MICROSTRUCTURE CHARACTERISTICS OF Cr3C2-NiCr COATINGS DEPOSITED WITH THE HIGH-VELOCITY OXY-FUEL THERMAL-SPRAY TECHNIQUE