Influence of microstructure on electrochemical property of new Al alloy

马正青,黎文献,谭敦强,肖于德

DOI: https://doi.org/10.3969/j.issn.1004-244X.2001.06.013

2001-01-01

Abstract:The microstructure and morphology of new Al alloys were observed by means of metalloscope and SEM.The electrochemic property of the alloys was researched by means of electrochemic method.The self-corrosion rate of the new Al alloys was evaluated.

What problem does this paper attempt to address?

Influence of Alloying Elements on Electrochemical Behavior and Microstructure of Al Anode Materials

王乃光,王日初,彭超群,冯艳,张纯,张嘉佩

2010-01-01

Abstract:A novel Al anode material was prepared by melting and casting with the protection of Ar.The effects of additive elements on performance of Al alloy anode were studied by orthogonal test.The phase structure,morphology and composition distribution of Al alloy were investigated by X-ray diffraction(XRD) analysis,scanning electron microscopy(SEM) and energy dispersive spectroscopy(EDS).The electrochemical and corrosion performances of Al anode were studied by dynamicpotential polarization curves,hydrogen evolution and galvanostatic tests.The results show that Mg is the most dominant element influencing work potential and corrosion current density of Al anode materials.Low content of Mg contribute to negative work potential and low corrosion current density of Al anode.In is the most dominant element influencing the rate of hydrogen evolution and high content of In can reduce the rate of hydrogen evolution.
Influence of Cr on Microstructure and Electrochemical Properties of FeNiMnCuCrx High-entropy Alloy

XIONG Mei,GAN Zhang-hua,DAI Yi,LIANG Yu,WAN Chao,LI Mian

DOI: https://doi.org/10.11973/fsyfh-201703003

2017-01-01

Abstract:The effects of Cr content on the variation of phase structure,microstructure and electrochemical properties of FeNiMnCuCrx high-entropy alloys were investigated by X-ray diffraction (XRD),scanning electron microscope (SEM),energy dispersive spectrometer (EDS) and electrochemical testing.The results showed that the alloys were FCC phase;the phase structure turned from single set of FCC to double sets of FCC with the increase of Cr.The microstructure transformed from columnar dendrites to equiaxed dendrites when the Cr content increased,and the microstructure refined.With the addition of Cr,the free corrosion current density showed the tendency of increasing first and decreasing afterwards.When ax was equal to 1,the corrosion current density showed the lowest value of 7.8167×10-7 A/cm2.
Influence of Microstructure and Microelements on Corrosion Structure of Aluminum Foil

毛卫民,蒋恒,杨平,冯惠平,余永宁

DOI: https://doi.org/10.3321/j.issn:1004-0609.2004.10.001

2004-01-01

The Chinese Journal of Nonferrous Metals

Abstract:The surface corrosion structures of aluminum foils, which were annealed at 300 ℃ followed by rapid and slow cooling respectively, were observed after electrochemical etching. The distributions of microelements Fe, Si, Cu and Mg in the surface layer were also determined by secondary ioo mass spectrometer. It is found that the Mg content at external surface is increased exponentially over the four orders of magnitude in comparison with that in center layer. The corresponding contents of Fe and Si are increased about two orders of magnitude; while the content of Cu is increased lower than one order of magnitude. The slow cooling after annealing will lead to stronger segregation of microelements around the grain boundaries and dislocations in the surface, which aggravates the (inhomogeneity) of corrosion structure and results in low specific capacity.
Microstructure and Electrochemistry Properties of New Aluminum Alloy Anodes

马正青,黎文献,肖丁德,余琨

DOI: https://doi.org/10.3969/j.issn.1001-1560.2002.05.004

2002-01-01

Abstract:Two types of new aluminum alloys were developed as sacrificial anode material. The electrochemical properties, microstructure and surface corrosion morphology of the aluminum alloy anode in alkaline NaCl solution (25%KOH + 3.5%NaCl) were determined by electrochemical methods, metalloscope and SEM. Results showed that the electrochemical properties of Al alloy anode was depended on the microstructure. Breakdown of oxidation film, acceleration of dissolution, decrease of anodic polarization and negative increase of potential occurred owing to the second phase and concentrating of alloy elements. The impurity tolerance, electrochemistry properties and surface corrosion uniformity of anode material were improved with trace elements solid-melted in matrix and well-distributed second phase. Corrosion rate of alloy was so low that availability of anode was increased.
Effect of Microstructure on the Mechanical and Corrosion Behaviors of a Hot-Extruded Nickel Aluminum Bronze

Datong Zhang,Ruiping Chen,Weiwen Zhang,Zonggiang Luo,Yuanyuan Li

DOI: https://doi.org/10.11890/1006-7191-102-113

2010-01-01

Abstract:In this paper, the influence of microstructure on the corrosion behavior of a hot-extruded nickel aluminum bronze was studied. Three kinds of samples subjected to the hot-extrusion, annealing and quenching conditions were prepared and immersion tests in 3.5% NaCl solution were carried out. Microstructures and corrosion surface morphologies of the samples were observed by SEM. It was found that the retained beta' martensite and (alpha+kappa(III)) lamella eutectoid in the as hot-extruded material were eliminated after annealing, and corrosion resistance of the alloy was improved. As to the as-quenched material, its corrosion rate was higher than that of the as hot-extruded material since the volume fraction of beta' phase which was anodic to alpha phase increased after quenching. As regards the mechanical properties, the as-quenched sample possesses the highest hardness and tensile strength among the three kinds of samples, while the as-annealed sample possesses the highest elongation. That is to say, heat treatment plays different roles in the mechanical properties and corrosion resistance of the experimental alloy.
Influence of magnesium contents on microstructure and electrochemistry behaviors of aluminum alloys for sacrificial anodes

Chang-rui LIU,Li HAN,Qing-juan WANG,Zhong-ze DU

DOI: https://doi.org/10.3969/j.issn.1007-7235.2007.04.011

2007-01-01

Abstract:To base on the alloy phase electrochemistry theorem,this work investigated the influence of magnesium contents on microstructure and electrochemistry properties of aluminum anodes.Experimental results indicated that the squares of phase Mg5Al8 were increased with Mg contents increasing,and the electrochemistry properties were better than before.When the Mg contents were increased form 1% to 30%,the open potential of Al-Mg anodes was reduced form-0.79 V to-1.18 V in 3.5% NaCl solution,and the polarization rate was also decreased.
Influence of Microstructure on Corrosion Properties of Mg-6Zn-1Mn-0.5Ca Alloy in Simulated Body Fluid

王勇,宋长江,谈春林,胡建旗

DOI: https://doi.org/10.13289/j.issn.1009-6264.2012.s2.012

2012-01-01

Abstract:As-extruded Mg-6Zn-1Mn-0.5Ca alloys were heat treated so as to change their microstructure.The effect of the distribution of alloying element and secondary phases on the corrosion performance in simulated body fluid was investigated.Optical microscope,scanning electron microscope and X-ray diffractometer were used to characterize the microstructure and crystal structure of the alloy.The bio-corrosion properties were explored by immersion corrosion,hydrogen evolution and electrochemical measurement.The results show that the as-annealed alloy has the best corrosion resistance.The composition is homogeneous.Secondary phase particles Ca2Mg6Zn3 are small and spherical,which distributed along the grain boundaries uniformly.
Microstructure evolution and electrochemical corrosion behavior of Al–Zn–Mg aluminum alloy

Teng Dun-Bo,Zhang Hong,Han Cui-Hong,Xu Yu-Rong,Liu Zhen,Zhang Ri-Qiang,Chen Xiao

DOI: https://doi.org/10.1088/2053-1591/ac6731

IF: 2.025

2022-04-01

Materials Research Express

Abstract:Abstract Electrochemical corrosion behavior of Sn-containing Al–Zn–Mg aluminum alloy has been studied in detail. The localized corrosion behaviors were studied by electrochemical impedance spectroscopy (EIS) analysis, and the potentiodynamic polarization measurements. The grain structure, grain-boundary microstructure, grain-boundary microchemistry, pitting and intergranular corrosion morphology were characterized and observed using SEM, EDS, TEM, SAED and HRTEM analyses. Based on these tests, the effects of grain-boundary on the corrosion resistance in our Sn-containing Al–Zn–Mg alloys before/after bake hardening were analyzed systematically. Finally, the relationship between chemical composition, microstructure evolution and corrosion behaviour was revealed. The results indicate that the bake hardening process improves the corrosion resistance compared to the pre-aging state. The grain size has little effect on the electrochemical corrosion bahavior.

materials science, multidisciplinary
Microstructure, Mechanical Properties and Corrosion Resistance of a Novel Mg-8Li-5Al-5Ca Alloy

DONG Peng,CHEN Ding,CHEN Zhenhua,ZHANG Kai

DOI: https://doi.org/10.11896/j.issn.1005-023x.2017.018.014

2018-01-01

Abstract:Mg-8Li-5Al-5Ca with high ratio of calcium and aluminum was designed.Its mechanical properties at room temperature and corrosion resistance were studied by the room temperature tensile test,weight loss method,pH tests and electrochemical tests.Also,microstructure and corrosion morphology of the alloy were analyzed by scanning electron microscopy (SEM) and X-ray diffraction (XRD).The results showed that a structure of double matrix (a-Mg-β-Li) surrounded with Al2Ca phases was formed in the Mg-8Li-5Al-5Ca alloy,and both the matrix and the second phases were obviously refined after hot extrusion.The corrosion resistance was improved compared with that of the common Mg-Li alloys.Coordinating the excellent plasticity of Mg-Li alloys and high strength of the magnesium alloys with high ratio of calcium and aluminum,the Mg-8Li-5Al-5Ca alloy had high tensile strength (222 MPa) and elongation (8.3％).
Effects of Al contents on microstructure and properties of Monel alloys

Fu Wang,Jun Zhang,Juntao Zou,Zhikang Fan,Fengshou Zhang,Xianghong Liu

2010-01-01

Rare Metal Materials and Engineering

Abstract:The effects of Al content on microstructure and properties of Monel alloy were studied by OM, SEM, an electrochemistry method and a mass loss method. The results show that the area ratio of divorcing eutectic gamma' in the interdendritic area gradually becomes larger with increasing of Al content from 2% to 4% (mass fraction). The mechanism of corrosion in the simulative sea water is pit corrosion under the conditions of different Al contents. Meanwhile, as the Al content increases, the corrosion resistance of the alloy in the simulative sea water increases first but then decreases. The Monel alloy with 3% Al addition has the best corrosion resistance in the experimental range.
Influence of microstructure on the corrosion behavior of lead alloys

Jie LI,Xiao-cong ZHONG,Liang-xing JIANG,Xiao-jun LV,Ye-xiang LIU

DOI: https://doi.org/10.3969/j.issn.1001-9731.2015.05.005

2015-01-01

Abstract:Lead alloys have been widely applied in hydrometallurgical electrowinning industry due to their high stability in H2 SO4 system.Their corrosion resistance not only affects the cost,but also determines the quality of cathode product.Hence,corrosion resistance is a critical factor to evaluate the performance of lead alloys. The effects of grain size,morphology and distribution of second phases,and rolling process on their corrosion behavior are briefly reviewed.The microstructure feature of lead alloys with ideal corrosion resistance is sum-marized,and the prospects of grain boundary engineering and micro-analysis of localized corrosion behavior of lead alloys are also proposed.
Influence of different dealloying methods on microstructure of nano-porous alloy

ZHOU Qi,LI Da-peng,WANG Wen-hui,ZHANG Zhi-mao

DOI: https://doi.org/10.3969/j.issn.1673-5196.2013.05.001

2013-01-01

Abstract:Alloys precursors were prepared with arc melting and vacuum rejection,by means of both chemical dealloying and electrochemical dealloying methods nano-porous alloy was prepared,and XRD, SEM and other equipment were used to analyse alloy phase composition and microstructure.The influence of different corrosive methods,corrosion potentials,corrosion time on the structure of the nano-porous alloy was investigated.The results showed that a uniform nano-porous alloy could be obtained with chemical dealloying corrosion,the average pore size being about 125nm,but there would be a larger size of the hole skeleton,approximately 150nm,and there was a small amount of an Al-containing phase in the remaining phase,that was hardly to be dealloyed completely.However,a uniform and double-continuous three-dimensional networked nano-porous alloy could be obtained with electrochemical dealloying in a 20% NaOH solution,and the pore size was about 100nm.
INFLUENCE OF ALUMINUM CONTENT ON MICROSTRUCTURE AND ATMOSPHERIC CORROSION BEHAVIOR OF MAGNESIUM-ALUMINUM ALLOYS

Ruiling JIA,Chuanwei YAN,Fuhui WANG

DOI: https://doi.org/10.3969/j.issn.1005-4537.2007.05.003

2007-01-01

Abstract:Microstructure and phase constituent of magnesium-aluminum alloys adding different aluminum content(3.4 mass%,9.3 mass%,20.7 mass%)were investigated utilizing the scanning electron microscopy(SEM) equipped with energy-dispersive analysis of X-ray(EDAX) and X-ray diffraction(XRD).The influence of microstructure on the corrosion morphologies was observed after corrosion tests in laboratory simulated atmosphere.The results indicated that magnesium-aluminum alloys with different aluminum content in the atmospheric environment had different corrosion behavior due to amount and distribution of the β phase(Mg17Al12).Mg-3Al alloy was approximately single-phase alloy,while Mg-9Al alloy and Mg-21Al alloy were two-phase alloys.There were more β phase in Mg-21Al alloy than in Mg-9Al alloy because of its higher aluminum content.Mg-3Al alloy exhibited better atmospheric corrosion resistance than Mg-9Al alloy and Mg-21Al alloy.There were fewer corrosion products on the surfaces of Mg-3Al specimens,while severe corrosion was found to take place in both Mg-9Al alloy and Mg-21Al alloy due to the presence of the β phase in them.More specifically,it was discovered that due to the absence of the couple-actuation of β phase,the corrosion of single-phase alloy Mg-3Al may be attributed solely to the pitting caused by high concentration of Cl-near the NaCl deposits.However,with Mg-9Al alloy and Mg-21Al alloy,a more important factor for corrosion is the presence of β phase.Under couple-actuation of the negative of β phase,α phase causes a corrosion along the depth extent.
Study of Anodizing Al-Li Alloy and Properties of the Anodization Film

马宗耀,谢发勤

DOI: https://doi.org/10.3969/j.issn.1000-4742.2008.06.010

2008-01-01

Abstract:The anodization film was prepared by controlled mode of constant-voltage on Al-Li alloy surface in H2SO4 solution. The effects of additives on the morphology,hardness and corrosion resistance of the film were investigated by scanning electron microscopy (SEM)and electrochemical corrosion testing method. The results show that the hardness of the film is improved remarkably when oxalate is added to the electrolyte solution; and the anodization film formed on Al-Li alloy surface exhibits the best corrosion resistance in the mass fraction of 3.5%NaCl solution when oxalate and NiSO4 are added.
Investigation of Corrosion Behaviour of Al-40Si-0.35Re Alloy

ZHANG Yu,WANG Yu-xin,LIAO Wen-jun,WANG Hua-yu,YANG Ying,YAN Biao

DOI: https://doi.org/10.13228/j.boyuan.issn1005-8192.2010.05.008

2010-01-01

Abstract:Electrochemical corrosion behaviors of Al-40Si-0.35Re alloy which made by casting and spray method separately were studied by linear polarization method.The microstructure of samples before and after corrosion was analyzed by scanning electron microscopy(SEM).The results showed that the spray-forming Al-40Si-0.35Re alloy behaves a refined microstructure,however,the corrosion resistance obviously decrease compared with the casting alloy.
Effect of Al on the Mechanical Properties and Corrosion Resistance of Pb-Al Alloy

Lu Zhicheng,Liu Zhenlin,Li Yongliang,Wu Dan,Wang Fuming

DOI: https://doi.org/10.1088/1757-899x/201/1/012045

2017-01-01

IOP Conference Series Materials Science and Engineering

Abstract:A set of binary Pb-Al alloys with different Al contents were designed in this work. The mechanical properties and corrosion resistance of Pb-Al alloys were investigated with help of tensile test, Charpy V-notch impact test and salt spray corrosion test (SSCT). And the microstructure was observed by optical microscopy. The results showed that microstructure of all alloys were twin structure, and the twin structure was gradually refined with the increase of Al content. Al dissolved in matrix could significantly improve the tensile strength, impact energy and corrosion resistance. However, a higher content of Al would harm the mechanical properties and corrosion resistance. It may be due to the heterogeneous precipitation of Al rich phase.
Investigation of Microstructures and Anti-corrosion Properties of Aluminium-Zinc Alloys

ZN Qi,CQ Zhang,RX Wang,CB Liu,ZL Chen

DOI: https://doi.org/10.1002/cjoc.200591182

IF: 5.56

2005-01-01

Chinese Journal of Chemistry

Abstract:Electro-chemical experiment was carried out to test the corrosion rates of aluminium-zinc hot-dip coating. It is shown that 5.3% aluminium-zinc alloy (weight ratio) has superior anti-corrosion property. The determined microstructure has displayed amorphous structure composed of nanometer sized particle of the system. The analysis indicated large negative change of Gibbs energy of 5.3% aluminium-zinc system. Molecular dynamics simulation showed that 5.3% aluminium-zinc system has very different behavior from other systems. A phase transition of this particular system was observed from simulation. The transition temperature was determined around 400 K. The simulation indicated that 5.3% aluminium-zinc system is amorphous over temperature range from 300 to 900 K, supporting the inference from experiments that amorphous solid of aluminium-zinc alloy has special anti-corrosion character.
The Microstructure Evolution and Electrochemical Corrosion Behavior of 7A46 Aluminum Alloy in Different Quenching Conditions

Yaru Liu,Lu Xing,Qing Zeng,Qinglin Pan,Sheng Li,Jun Liang,Haoru Yang

DOI: https://doi.org/10.3390/ma15020477

IF: 3.4

2022-01-01

Materials

Abstract:The quenching condition of aluminum alloy can affect the mechanical property and corrosion resistance of the profile. This paper is aimed at the low quench sensitivity of aluminum alloys. Scanning electron microscopy and transmission electron microscopy were used to analyze precipitate behaviors of the 7A46 aluminum alloy under different isothermal cooling conditions and microstructure evolutions of quench-induced precipitations. The effect of the different isothermal time on the corrosion resistance of the alloy, and the relationship between microstructure and corrosion resistance after quenching were revealed through electrochemical impedance spectroscopy and potentiodynamic polarization tests. Results show that corrosion sensitivity of the quenching-aged alloy is much higher than that of the double-aged (DA) alloy, and the corrosion resistance of the quenched alloy decreases firstly and then increases. Due to the high density of the matrix precipitates, the increased content of the impurity element, the discontinuity of the grain boundary precipitates and the widening of the precipitates free zone, the most serious degree of corrosion performance among the quenched alloys is 295 °C at 800 s, and the self-corrosion potential and self-current density is −0.919 V and 2.371 μA/cm2, respectively.
Influence of Micro-alloyed Pb and Chromate on the Corrosion Behavior of High Voltage Anode Aluminum Foil

Zuo Hong,MAO Wei-min

DOI: https://doi.org/10.3969/j.issn.1673-2812.2005.04.034

2005-01-01

Abstract:The electrochemical corrosion behavior of high voltage anode aluminum foil with and without a drop Pb, as well as its influence on the specific capacity were investigated, while the corrosion microstructure was also observed under SEM. It was shown that both of the chromic acid corrosion and the micro-alloyed Pb can initiate homogenous corrosion pores respectively, and increase the specific capacity. It is indicated that a more ecological technology for aluminum foil production needs to be developed.
Corrosion Behavior and Microstructure of Er Containing 5083 and 5A06 Al-Mg Alloys

CUI Chang-hua,GAO Kun-yuan,NIE Zuo-ren,WEN Sheng-ping,HUANG Hui

2011-01-01

Abstract:The corrosion behavior of hot rolled and annealedCat 350℃for 1h)Al-Mg alloys 5083 and 5A06 microalloyed with small amount of Er was investigated by means of immersion tests and electrochemical dynamic potential cycle polarization measurements.For the untreated samples and those after immersion tests,the morphology and microstructure were examined by optical microscopy(OM),scan electron microscopy(SEM),transmission electron microscopy(TEM)together with energy dispersion spectrum(EDS).The results showed that both 5083 and 5A06 with trace Er addition were of good corrosion resistance,and the corresponding corrosion rates were in the range ofμA/cm~2 when measured in 3.5%NaCl solution.The trace Er addition didn't worsen the corrosion-resistance.The high content of some major alloying element Mg affected greatly the corrosion behavior,and the heat treatment parameters had some effect as well.

Influence of microstructure on electrochemical property of new Al alloy

Influence of Alloying Elements on Electrochemical Behavior and Microstructure of Al Anode Materials

Influence of Cr on Microstructure and Electrochemical Properties of FeNiMnCuCrx High-entropy Alloy

Influence of Microstructure and Microelements on Corrosion Structure of Aluminum Foil

Microstructure and Electrochemistry Properties of New Aluminum Alloy Anodes

Effect of Microstructure on the Mechanical and Corrosion Behaviors of a Hot-Extruded Nickel Aluminum Bronze

Influence of magnesium contents on microstructure and electrochemistry behaviors of aluminum alloys for sacrificial anodes

Influence of Microstructure on Corrosion Properties of Mg-6Zn-1Mn-0.5Ca Alloy in Simulated Body Fluid

Microstructure evolution and electrochemical corrosion behavior of Al–Zn–Mg aluminum alloy

Microstructure, Mechanical Properties and Corrosion Resistance of a Novel Mg-8Li-5Al-5Ca Alloy

Effects of Al contents on microstructure and properties of Monel alloys

Influence of microstructure on the corrosion behavior of lead alloys

Influence of different dealloying methods on microstructure of nano-porous alloy

INFLUENCE OF ALUMINUM CONTENT ON MICROSTRUCTURE AND ATMOSPHERIC CORROSION BEHAVIOR OF MAGNESIUM-ALUMINUM ALLOYS

Study of Anodizing Al-Li Alloy and Properties of the Anodization Film

Investigation of Corrosion Behaviour of Al-40Si-0.35Re Alloy

Effect of Al on the Mechanical Properties and Corrosion Resistance of Pb-Al Alloy

Investigation of Microstructures and Anti-corrosion Properties of Aluminium-Zinc Alloys

The Microstructure Evolution and Electrochemical Corrosion Behavior of 7A46 Aluminum Alloy in Different Quenching Conditions

Influence of Micro-alloyed Pb and Chromate on the Corrosion Behavior of High Voltage Anode Aluminum Foil

Corrosion Behavior and Microstructure of Er Containing 5083 and 5A06 Al-Mg Alloys