Abstract:In the present work, the hydrodynamics behavior of a 3D small-scale cold flow modeling of a gas-solid tapered fluidized bed is evaluated with the Eulerian-Eulerian two-fluid modeling (TFM) approach. The sensitivity of different modeling parameters, including lift and virtual mass forces, viscous force, gas-solid drag force, granular temperature, granular viscosity, granular pressure, particle-wall specularity coefficient, particle-particle restitution coefficient, and particle-wall restitution coefficient, are systematically investigated to optimize the performance of the present numerical model. The results from different sensitivity analyses reveal that the gas-particle drag force is a more important force to resolve the correct time-averaged axial and radial solids holdup profiles of the tapered fluidized bed than the other investigated parameters. The highest accuracy possible from simulations is achieved from the Gibilaro drag model followed by the Arastoopour and EMMS/bubbling models. In contrast, all other drag models over-predict the gas-particle interaction force. The assessment of the lift and virtual mass forces, viscous force, granular temperature, granular viscosity, granular pressure, and particle-wall restitution coefficient results reveal that these parameters are less critical for the numerical simulations of the tapered fluidized bed than the gas-solid drag force. However, the assessment of particle-wall specularity coefficient and particle-particle restitution coefficient reveals that adjusting these parameters in the numerical simulations is helpful to achieve a better agreement between the experimental data and model results. For the higher gas flow rate, the current work shows that a better agreement can be achieved by tuning the parameter values in the standard sub-models than the previously published TFM studies. Meanwhile, for the lower gas flow rate, the accuracy of the present work is slightly lower than the previously published work but acceptable with the experimental measurements. The current work has an advantage over the previously published work in terms of lower computational effort by using the simplified geometry and mean particle diameter assumptions.

Two-Fluid Model Simulations of the National Energy Technology Laboratory Bubbling Fluidized Bed Challenge Problem

Experimental and numerical investigation of solid behavior in a gas–solid turbulent fluidized bed

Numerical Simulations of a Bubbling Fluidized Bed Reactor with an Energy Minimization Multiscale Bubble Based Model: Effect of the Mesoscale

Numerical Simulations of Flow Structure and Heat Transfer in a Central Jet Bubbling Fluidized Bed

CFD Simulation and Experiments of Dynamic Parameters in Gas–solid Fluidized Bed

Effect of Bed Thickness on a Pseudo 2D Gas-Solid Fluidized Bed Turbulent Flow Structures and Dynamics

A Simulation Study of Gas-Solid Two Phase Flow in a Bubbling Fluidized Bed with Various Drag Force Models

Three Dimensional Full-Loop Numerical Simulation of a CFB and Experimental Verification

Computational Fluid Dynamics Simulations of Interphase Heat Transfer in a Bubbling Fluidized Bed

Validation and Sensitivity Analysis of an Eulerian-Eulerian Two-Fluid Model (TFM) for 3D Simulations of a Tapered Fluidized Bed

Comprehensive Assessment of the Accuracy of CFD-DEM Simulations of Bubbling Fluidized Beds

Heterogeneity Analysis of Gas-Solid Flow Hydrodynamics in a Pilot-Scale Fluidized Bed Reactor

Verification of Optimal Models for 2D-Full Loop Simulation of Circulating Fluidized Bed

Numerical simulation of flow behavior in liquid-solid fluidized bed

Hydromechanical Simulation of A Bubbling Fluidized Bed Using an Extended Bubble-Based Emms Model

Two-Fluid Simulation of a Three-Dimensional Spout-Fluid Bed: Flow Structures, Regimes, and Insight into the Mechanism of Particle–Particle Momentum Transfer

MULTI-SCALE SIMULATION ON HYDRODYNAMIC CHARACTERISTICS IN BUBBLING FLUIDIZED BED

Coarse-grid simulations of full-loop gas-solid flows using a hybrid drag model: Investigations on turbulence models

Using Mesoscale Drag Model-Augmented Coarse-Grid Simulation to Design Fluidized Bed Reactor: Effect of Bed Internals and Sizes

Multi-scale CFD Modeling of Gas-Solid Bubbling Fluidization Accounting for Sub-Grid Information

Validation of filtered two-fluid models for gas–particle flows against experimental data from bubbling fluidized bed