Abstract:An electrochemical (EC) gas sensor is a 3+ terminal electrochemical device which, when biased correctly with a potentiostat circuit, behaves as a current source whose output is proportional to the target gas concentration. The short lifetime of these sensors has become a key functional safety issue for hazardous gas detection modules. In order to predict the failure of EC gas sensors, a high precision and wide bandwidth EC impedance measurement is required [1]. For example, an electrochemical impedance spectroscopy (EIS) instrument is often used in the laboratory for failure rate analysis and there is a trend towards integration of the EIS at the chip level. However, it is extremely challenging to integrate the precision high-speed/high-power EIS with the precision low-power EC potentiostat system. For instance, [2] demonstrated a very low-power integration of the EIS and bio-potentiostat; however the EIS bandwidth is only 80Hz and the EIS dynamic range (DR) is limited at 77dB. [3] and [4] presented good EIS performance because there were no trade-off limitations between the low-power module and the high speed EIS. Furthermore, two additional challenges, not met by [2]–[4], are to apply an AC stimulus without disturbing the large DC potentiostat and to improve the DR for stimulus-sensitive sensors. This paper demonstrates a highly integrated SoC to support EIS applications for diverse sensors. Figure 17.4.1 shows the implemented architecture. The analog front end (AFE) and digital back end (DBE) are implemented on a 0.18μσι die and a 90nm die respectively and stacked in a 5×6×1mm3 LGA package. A Cortex-M3, featuring UART/SPI/I2C interfaces, is integrated in the top DBE die. The bottom AFE die has two EC potentiostat channels, with sensor readout, as well as a chip scale 0.1Hz∼200kHz EIS solution, which is realized by a transmitter (Tx), receiver (Rx) and DSP. A sequencer can flexibly control all these modules through a programmable 6KB SRAM, which is shared by command memory and data FIFO.

A High Dynamic Range Cmos Readout Chip for Electrochemical Sensors

A Dual-Channel Wide Input Range Interface Circuit for Electrochemical Amperometric Sensors

A Cmos Analog Front-End Chip for Amperometric Electrochemical Sensors

A CMOS Detection Chip for Amperometric Sensors with Chopper Stabilized Incremental △∑ ADC

A high dynamic range analog-front-end IC for electrochemical amperometric and voltammetric sensors

A high-performance polycarbonate electrophoresis microchip with integrated three-electrode system for end-channel amperometric detection.

Dual-Mode Sensing Chips for Wide-Range and High-Accuracy Biomarker Detection

Wide dynamic range multi-channel electrochemical instrument for in-field measurements

CMOS-based On-Chip Electrochemical Sensor

Low-Noise and Process Variation-Tolerant Readout Circuit for Electrochemical Sensors

CMOS Potentiostat for Chemical Sensing Applications

A 97 Db Dynamic Range Csa-Based Readout Circuit With Analog Temperature Compensation For Mems Capacitive Sensors

A Wide Dynamic Range And Fast Update Rate Integrated Interface For Capacitive Sensors Array

Design of a 68 Db Input Dynamic Range Potentiostat for Electrochemical Biosensing

A fully integrated CMOS nanoscale biosensor microarray.

A 0.28mΩ-sensitivity 105dB-dynamic-range electrochemical impedance spectroscopy soc for electrochemical gas detection

An Electrochemical CMOS Biosensor Array Using Phase-Only Modulation With 0.035% Phase Error And In-Pixel Averaging

A Voltage-Assist 16-Channel Electrochemical Biosensor with Linearity Compensation

A CMOS Pixelated Nanocapacitor Biosensor Platform for High-Frequency Impedance Spectroscopy and Imaging

A Low-Current and Multi-Channel Chemiresistor Array Sensor Device

Opto-electronic DNA Chip: High Performance Chip Reading with an All-Electric Interface