Abstract:Al-7Si-Mg alloy castings have extensive applications in automotive industries, and the tensile properties of these alloys including yield strength, ultimate tensile strength and elongation are commonly used to judge their mechanical properties. In this work, the modified precipitation kinetics model, yield strength model and strain hardening model have been proposed to predict the tensile properties of Al-7Si-Mg alloys. The precipitation kinetics model can be used to predict the precipitate microstructure parameters including the precipitate density, size, size distribution, volume fraction, and composition and so on in these alloys, combining which with the strength model, their yield strengths can be obtained. The strain hardening model can be applied to simulate the stress-strain curves during tensile process, and the ultimate tensile strengths and elongations can be obtained by combining this model with the experimental data fitted with the expression (sigma(UTS)-sigma(Y))=m center dot sigma(Y)+n+f(T-ss). First, the evolution of precipitate microstructure parameters and yield strengths as a function of ageing time were simulated, and then their comparisons with the experimental results were performed. The possible reasons resulting in the deviations between simulated and experimental yield strengths were analyzed. The stress-strain curves during tensile process of Al-7Si-0.36Mg alloy were simulated using strain hardening model, and the influences of ageing treatment and as-cast microstructure refining scale on the parameters of dislocation storage rate, dynamic recovery rate and the stress-strain curves were analyzed. Then, the ultimate tensile strengths and elongations of Al-7Si-0.4Mg alloy aged at different temperatures were predicted which are in better agreement with the experimental results, and the influence of secondary dendrite arm spacing on tensile properties was also analyzed. Finally, the limitation of present model and the factors influencing the prediction precision of tensile properties were outlined.

A Model for Prediction of Yield Stress of Heat Treated Al-7Si-Mg Cast Alloys

An integrated model for prediction of yield stress in Al 7Si Mg cast alloys

Modeling the Precipitation Kinetics and Tensile Properties in Al-7si-Mg Cast Aluminum Alloys

Modeling Microstructure and Yield Strength during Solidification and Heat Treatment Process in Al-7Si-Mg Cast Aluminum Alloys

Modeling of Strain Hardening Behavior and Mechanical Properties of Al 7Si Mg Cast Aluminum Alloys During Tensile Process

Prediction of Yield Strength at Room Temperature for Squeeze Cast A226

Microstructure based analysis and predictive modeling of cast Al7Si1.5Cu0.4Mg alloy mechanical properties

Correlation of Solidification Microstructure Refining Scale, Mg Composition and Heat Treatment Conditions with Mechanical Properties in Al-7Si-Mg Cast Aluminum Alloys

Modelling Investigation of Precipitation Kinetics and Strengthening for Needle/Rod-Shaped Precipitates in Al-Mg-Si Alloys

A Yield Stress and Work Hardening Model of Al-Mg-Si Alloy Considering the Strengthening Effect of β” and β’ Precipitates

MICROSTRUCTURE SIMULATION AND MECHANICAL PROPERTY PREDICTION OF MAGNESIUM ALLOY CASTING CONSIDERING SOLID SOLUTION AND AGING PROCESS

The Flow Stress Behavior and Physical-Based Constitutive Model for As-Quenched Al-Zn-Mg-Cu Alloy

Experimental Characterization and Yield Strength Model for Process-Structure-Property of Selective Laser Melted 316L

Modelling the Effect of Room Temperature Storage and Deformation on the Age-hardening Behaviour of Al-Mg-Si alloys

Modeling high-temperature stress-strain behavior of cast aluminum alloys

Dynamic Recrystallization Critical Conditions and a Physically–Based Constitutive Model of Al–4.8Mg Alloy Under Hot Working Conditions

Multi-scale Simulation of Al–Cu–Cd Alloy for Yield Strength Prediction of Large Components in Quenching-Aging Process

A Microstructure‐Strength Calculation Model for Predicting Tensile Strength of AlSi7Mg Alloy Castings

A Physical-Based Plane Stress Constitutive Model for High Strength AA7075 under Hot Forming Conditions

Establishment of nucleation model and microstructure simulation of Al-Si alloy for low pressure die casting

Theoretical prediction of the temperature-dependent yield strength of solid solution strengthening Nickel-based alloys