Abstract:In this experimental study, a porous material is used inside the pipes of the evaporator as the main heat exchanging device in the air conditioning cycle. The used porous material consists of stainless steel balls of different diameters. As a case study, refrigerant R454B, which is a drop‐in replacement to refrigerant R410A, is used as a working fluid in the air conditioner thermodynamic cycle. Four different porosities were used during the experimental tests; 100% (empty tube), 46%, 40%, and 33%. This study investigated the influence of variation of porosity as well as outside air temperature and refrigerant evaporation temperature on the cycle coefficient of performance, evaporation capacity, pressure drop, and power consumption during the compression process. Measured evaporation temperatures and indoor temperatures during tests were in the range of 1.5–12°C and 18–25°C, respectively. The use of porous material in the evaporation heat exchanger resulted in a considerable increase in the cycle evaporation capacity and coefficient of performance. Varying porosity from 100% to 33% resulted in an average percent increase of cycle evaporation capacity and coefficient of performance by 48.8% and 84.3%, respectively. Also, decreasing porosity from 100% to 33% resulted in an average percent increase in power consumption during the compression process by about 27%. An average percent increase of power consumption of compressor by about 25.9% is also reported, when evaporation temperature increased from 1.5°C to 12°C. Increasing outside air temperature from 27.1°C to 39.5°C resulted in decreasing evaporation capacity and coefficient of performance by 35.2% and 34.5%, respectively, and in increasing compressor power consumption by about 14.3%. A considerable pressure drop was recorded during the evaporation process when using porous material. The volumetric evaporation capacity, as well as compressor discharge temperature, are increased by increasing evaporating temperature and by decreasing evaporator porosity. The increase in air ambient temperature resulted in a considerable increase in refrigerant mass flow rate.

Evaporator Performance Enhancement by Pulsation Width Modulation (PWM)

Heat Transfer Measurement and Flow Regime Visualization of Two-Phase Pulsating Flow in an Evaporator

Experimental Study on Liquid-Vapor Two-Phase Pressure Drop of Pulsating Flow in an Evaporator

Performance Analysis of a New Ejector Enhanced Vapor Injection Heat Pump Cycle

An experimental study exploring heat transfer enhancement in tube in tube heat exchanger with pulsating flow

Performance Investigation of a Pressure Pulsation Dampener Applied in the Discharge Chamber of a Twin Screw Refrigeration Compressor

Continuous versus pulsating flow boiling. Experimental comparison, visualization, and statistical analysis

Experimental Research on the Performance of a Refrigerant Generating Bubble Pump Based on a Diffusion Generation Process with H2O HCOOK-R134a

Theoretical and Experimental Research on the Performance of a Refrigerant Generating Bubble Pump with a High-Accuracy Semi-Empirical Model

Investigation of characteristics of discharge pressure pulsation in a twin-screw refrigeration compressor

Effect of venting the periodic reverse vapor flow on the performance of a microchannel evaporator in air-conditioning systems

Simulation Study on the Performance of a Vapor-Bypassed Evaporator for Heat Pump Applications

Analysis of Enhanced Heat Exchange Caused by Pressure Pulsation in Cooler of Reciprocating Compressor

Periodic Reverse Flow and Boiling Fluctuations in A Microchannel Evaporator of an R134a Mobile Air-Conditioning System

Periodical reverse flow and boiling fluctuations in a microchannel evaporator of an air-conditioning system

Effect of airflow distribution shape on the performance of finned-tube evaporator in air-conditioning

Model of R134a Liquid–Vapor Two-Phase Heat Transfer Coefficient for Pulsating Flow Boiling in an Evaporator Using Response Surface Methodology

Experimental investigation on thermal performance of pulsating heat pipe by using Dowtherm – A

Study on the Pulsed Flow Control on Radiant Cooling and Heating Systems in Part Load

Performance enhancement of a split air conditioner using porous material inside the evaporator pipes

Experimental Study of a Counter-Flow Regenerative Evaporative Cooler