Abstract:High temperature proton exchange membrane fuel cells (HT-PEMFC) operated at a temperature range from 120 degrees C to 200 degrees C show high reaction kinetics, high tolerance of the Pt catalyst for impurities such as carbon monoxide and simplified water and heat management. HT-PEMFC has attracted great attentions in many applications including portable devices, unmanned vehicles and fuel cell cars. One of the essential components of the HT-PEMFC is high temperature proton exchange membrane (HT-PEM). The state-of-the-art HT-PEM is phosphoric acid (PA) doped polybenzimidazole (PBI) composite membrane. Phosphoric acid acts as the proton conductor while the PBI plays as a skeleton to hold the PA molecules and provides mechanical strength for the composite membrane. Nevertheless, the complex fabrication procedures and expensive cost hinder wide application of PBI in IIT-PFMPC. Alternative polymer skeletons including polyvinylpyrrolidone and amino-functionalized proton exchange membrane have been developed for the HT-PEM. Generally, the high proton conductivity of the HT-PEMs results from high doping level of PA. However, the plasticizer effect of PA molecules reduces the Van der Waals force among the polymer macromolecules. That leads to the low mechanical strength of the HT-PEMs. Cross-linking method significantly increases the mechanical strength of the HT-PEMs. On the other hand, the cross-linking reaction consumes the PA doping site of the HT-PEMs, leading to the low proton conductivity of these HT-PEMs. In this research, a novel self-crosslinked polyethyleneimine-polysulfone (PEI-PSF) HT-PEM with both high mechanical strength and high proton conductivity has been designed. The PEI molecules are anchored to the PSF backbones by chloromethylation and tertiary aminating reactions. That is prone to enhance the mechanical strength of the membrane. In addition, the PEI also acts as PA adsorption sites, which improves the PA doping level and proton conductivity of the HT-PEM. The degree of crosslinking is controlled by the degree of chloromethylation. The H-1 nuclear magnetic resonance characterization shows successfully graft of benzyl chloride onto the PSF backbone to form chloromethylated polysulfone (CMPSF). In addition, the X-ray photoelectron spectra confirm the reaction of PEI with CMPSF to form a self-crosslinked PEI-PSF membrane. With the increase of crosslinking degree, the PA doping level of the PEI-PSF membrane increases whereas its tensile strength decreases. A proton conductivity of 3.4 X10(-2) S.cm(-1) is obtained for a PEI-PSF membrane with a chloromethylation degree of 58%, denoted as PEI-PSF-58, and PA doping level of 122 wt% at 150 degrees C under anhydrous conditions. Meanwhile, the PEI-PSF-58 membrane remains excellent mechanical property with tensile strength of 30 MPa at room temperature. Moreover, HT-PEMFC based on the PEI-PSF-58 membrane exhibits a high peak power density of 200 mW.cm(-2) and outstanding stability under 150 C with a constant cell voltage of 0.4 V. In summary, a series of self-crosslinlced PEI-PSF HT-PEMs with both high proton conductivity and excellent mechanical properties have been synthesized. The self-crosslinking is a promising strategy to cope with trade-off between high proton conductivity and mechanical strength for the conventional PA doped HT-PEMs.

Constructing Anhydrous Proton Exchange Membranes Based on Cadmium Telluride Nanocrystal-Doped Sulfonated Poly(ether Ether Ketone)/polyurethane Composites

Sulfonated Polyaryletherketone with Pendant Benzimidazole Groups for Proton Exchange Membranes

HT-PEMs Based on Nitrogen-Heterocycle Decorated Poly (arylene Ether Ketone) with Enhanced Proton Conductivity and Excellent Stability

Achieving Better Balance on the Mechanical Stability and Conduction Performance of Sulfonated Poly(ether Ether Ketone) Proton Exchange Membranes Through Polydopamine/polyethyleneimine Co-Modified Poly(vinylidene Fluoride) Nanofiber As Support

Gel-state Polybenzimidazole Proton Exchange Membranes with Flexible Alkyl Sulfonic Acid Side Chains for a Wider Operating Temperature Range (25–240 °C)

3d Network Structural Poly (Aryl Ether Ketone)-Polybenzimidazole Polymer For High-Temperature Proton Exchange Membrane Fuel Cells

Fabrication of PBI/SPOSS Hybrid High-Temperature Proton Exchange Membranes Using SPAEK As Compatibilizer

Novel High Temperature Proton Exchange Membranes Based on Functionalized Poly(arylene Dimethylamino Benzene) Polymers

Phosphoric Acid Doped High Temperature Proton Exchange Membranes Based on Comb-Shaped Polymers with Quaternized Graft Architectures

Constructing Anhydrous Proton Exchange Membranes Through Alternate Depositing Graphene Oxide and Chitosan on Sulfonated Poly (vinylidenefluoride) or Sulfonated Poly(vinylidene Fluoride-Co-hexafluoropropylene) Membranes

Self-crosslinked Polyethyleneimine-polysulfone Membrane for High Temperature Proton Exchange Membrane

Dual Cross-Linked Organic-Inorganic Hybrid Polymer Electrolyte Membranes Based on Quaternized Poly(ether Ether Ketone) and (3-Aminopropyl)triethoxysilane

Submicro-Pore Containing Poly(Ether Sulfones)/Polyvinylpyrrolidone Membranes For High-Temperature Fuel Cell Applications

Construction of High-Performance, High-Temperature Proton Exchange Membranes through Incorporating SiO2 Nanoparticles into Novel Cross-linked Polybenzimidazole Networks

Spacer-engineering construction of continuous proton transport networks for cardo poly(biphenyl indole) high-temperature proton exchange membranes

In Situ Crosslinking of Polyoxometalate-Polymer Nanocomposites for Robust High-Temperature Proton Exchange Membranes

A Novel Comb-Shaped Polybenzimidazoles Crosslinked Sulfonic Acid Functionalized Polyphosphazenes High Temperature Proton Exchange Membrane

Polyoxometalate-Cross-Linked Proton Exchange Membranes with Post-Assembled Nanostructures for High-Temperature Proton Conduction

Tetramethyl poly(aryl ether ketone) modified by DABCO cationic polymer for high temperature proton exchange membrane fuel cells

Sulfonated Polyether Ether Ketone Composite Proton Exchange Membranes Incorporated with a Novel Hierarchical‐structure Hybrid Nanofiller Consisting Solid Superacid Zirconium Phosphate and CNTs

Semi-crystalline Sulfonated Poly(ether Ketone) Proton Exchange Membranes: the Trade-off of Facile Synthesis and Performance.