Abstract:The uniform bubble distribution is ensured to gain sufficient performance of dense fluidized bed reactors. Although distributor plays an important role in obtaining homogenous and small bubbles, the highly inelastic energy dissipation from solids bed triggers non-uniform bubbles growth. Hence, the total solids pressure loading ( T) is introduced here to present the interaction between contribution from solids bed and distributor. The boundary between uniform and non-uniform bubble growth can be detected by criterion based on Prigogine’s minimum of the entropy production principle. Furthermore, an industrial case is studied further based on stability analysis and new operational conditions are provided to improve the performance through eliminating non-uniform bubble growth. INTRODUCTION Consider gas solids fluidization that begins in an initial state of uniform density where gas is evenly introduced into the base of the bed via distributor. The solids then “cools” as the collisions dissipate the kinetic energy of the initial condition, and the cooling solids do not remain homogenous, i.e. the state of uniform density is unstable so that the system totally exhibits the coexistence of two phases: clusters and bubbles. Thus, uniform gas solids distribution, resulting from the distributor, will be damaged by solids beds itself and this process is self-aggregating until the size of large bubbles reaches the bed diameter1-4. Recent studies have shown that non-uniform bubble growth even slugging may occur in a sufficiently deep bed, as exemplified in Fig. 1. The result of this phenomenon will resist mass transfer and bypass reactant in the form of large bubbles or slugs, leading to poor conversion and selectivity in reactors. Therefore, a deep fluidized bed is a fundamental model in uniformity breaking mechanics and should be investigated carefully to ensure the performance of fluidized bed reactors. Fig. 1. Illustration of the mal-distribution in a deep fluidized bed. STABLITY ANALYSIS The distribution of bubbles is distributed uniformly through the distributor, while the uniformity is broken due to inelastic energy dissipation from solids beds. Therefore, in order to describe the multi-phase interaction in dense fluidization, the dimensionless number total solids pre T), i.e. the pressure ratio between solids bed and distributor, is introduced here:

Force Characteristic of a Large Dense Object in a Fluidized Bed Equipped with an Inclined Air Distributor

Experimental and numerical investigation of solid behavior in a gas–solid turbulent fluidized bed

Characterization of Flow Pattern of Cohesive Particles in Gas-Solid Fluidized Bed Via Axial Distribution of Particle Motions

CFD Simulation of an Agitated Gas-Fluidized Bed: Effects of Particle–particle Restitution Coefficient on the Hydrodynamics

Experimental and Numerical Study of Solids Concentration Distribution in Transition Section of Turbulent Fluidized Bed

Solid Concentration and Velocity Distributions in an Annulus Turbulent Fluidized Bed

CFD Simulation and Experiments of Dynamic Parameters in Gas–solid Fluidized Bed

Experimental Investigation of Bubble and Particle Motion Behaviors in A Gas-Solid Fluidized Bed with Side Wall Liquid Spray

Experimental Investigation of Electrostatic Effect on Particle Motions in Gas-Solid Fluidized Beds

Effect of inclined distributor on the motion behavior of a large spherical object in the bottom zone of a fluidized bed

Electrostatic Distribution in the Riser of the Multizone Circulating Fluidized Bed for Polypropylene

Dispersion Trajectory and Dynamics of Particles Injected from the Sidewall in the Gas–Solid Fluidized Bed

CFD-DEM study of impacts of the porous distributor medium on fluidization characteristics of a 2D-fluidized bed

Time-series Analysis of the Characteristic Pressure Fluctuations in a Conical Fluidized Bed with Negative Pressure

Effects of Interparticle Forces on Fluidization Characteristics in Liquid-Containing and High-Temperature Fluidized Beds

Experimental characterizing the residence time distribution of large spherical objects immersed in a fluidized bed

Gas and Powder Flow Characteristics of Packed Bed: A Two-way Coupled CFD-DEM Study

Effect of Bed Thickness on a Pseudo 2D Gas-Solid Fluidized Bed Turbulent Flow Structures and Dynamics

12th International Conference on Fluidized Bed Technology UNIFORM BUBBLE GROWTH IN FLUIDIZED BED AND ITS STABILITY ANALYSIS

Statistical Study of the Distribution of Voidage in a Bubbling Fluidized Bed with a Constant Section

A Euler-Euler Hydrodynamic Modelling and Simulation of Dense Particle Flow in a Small-Scale Fluidized Bed