Abstract:An in-situ compatibilized starch (St) and polyacrylonitrile (PAN) composite spinning solution was designed by preparing starch-graft-polyacrylonitrile (St-g-PAN) through graft copolymerizing acrylonitrile from soluble starch and using ammonium cerium nitrate (CAN) as initiator. As dimethyl sulfoxide (DMSO) was used as the solvent, St/St-g-PAN/PAN/DMSO spinning solution was prepared and St/St-g-PAN/PAN composite fibers were obtained by dry-wet spinning technique. The effects of air gap, coagulation bath, hot drawing and stretching, and thermal-setting process were studied in detail. Fourier transform infrared spectroscopy (FT-IR), solid state nuclear magnetic resonance (13C NMR), thermogravimetric analysis (TGA), X-ray diffraction analysis (XRD), and scanning electron microscopy (SEM) were used to characterize the structure and morphology of the copolymer and the fibers. Single fiber strength tester and sonic orientation instrument were performed to measure the fiber mechanical properties and orientation degrees. The results showed that as the grafting ratio ~150.0% and the reacting mixture containing St ~9.8%, St-g-PAN ~81.6%, and homo-PAN ~8.6% in DMSO solution with 6.0 wt% in concentration were used, the spinning parameters such as air gap ~35 mm, coagulation bath concentration ~70%, temperature ~25 °C, and positive stretching ~48%, hot drawing and stretching 6 times at 80 °C, thermal-setting at 90 °C for 3 h under constant length mode were met, composite fibers with breaking strength 3.41 cN·dtex−1, breaking elongation 14.41%, sonic orientation factor 0.625, moisture recovery ratio 10.53% under standard condition (1 atm, 22 °C, and relative humidity 65%), and boiling water shrinkage ratio 9.60% were obtained. The as prepared composite fiber was better than common viscose fiber 2.11 cN·dtex−1 and cotton fiber ~3.24 cN·dtex−1 and expected to be used in the fields of medical gauze, bandage, protective clothing, et al. besides of common textiles. The in-situ compatibilization method can be applied in preparation of other composite polymer materials.

Stabilization Kinetics of Gel Spun Polyacrylonitrile/lignin Blend Fiber

On the structural changes, mechanism and kinetics of stabilization of lignin blended polyacrylonitrile copolymer fiber

Crystallization behavior and mechanical properties of bio-based green composites based on poly(L-lactide) and kenaf fiber

Insight into stabilization behaviors of Lignin/PAN-derived electrospun precursor fibers

Dry-Jet Wet Spinning of Thermally Stable Lignin-Textile Grade Polyacrylonitrile Fibers Regenerated from Chloride-Based Ionic Liquids Compounds

Fabrication and Characterization of Electrospun Poly(acrylonitrile- co-Methyl Acrylate)/Lignin Nanofibers: Effects of Lignin Type and Total Polymer Concentration

Transformation of Specific Dispersion Interactions between Cellulose and Polyacrylonitrile in Solutions into Covalent Interactions in Fibers

Accelerating the formation of the conjugated ladder structure of Poly(acrylonitrile-co-vinyl acetate) by cross-linked poplar lignin doped with boron phosphate

In-situ compatibilized starch/polyacylonitrile composite fiber fabricated via dry-wet spinning technique

Structural Transformation of Polyacrylonitrile (PAN) Fibers during Rapid Thermal Pretreatment in Nitrogen Atmosphere

Oxidative Stabilization of Pan/Vgcf Composite

Preparation, Stabilization and Carbonization of a Novel Polyacrylonitrile-Based Carbon Fiber Precursor

Synthesis and Processing of Melt Spun Materials from Esterified Lignin with Lactic Acid

Terpolymers of acrylonitrile, methyl acrylate, and 2‐acrylamido‐2‐methylpropane sulfonic acid for carbon fiber precursor: Effect of comonomers on the thermal stabilization of polyacrylonitrile copolymers

Effects of Moisture Content and Heat Treatment on the Viscoelasticity and Gelation of Polyacrylonitrile/Dimethylsulfoxide Solutions

Multi‐step heating strategy during thermal stabilization of polyacrylonitrile multi‐filament bundle before carbonization

Carbon Fibers Precursors from Lignin and Cellulose Acetate via Melt‐Spinning

Stabilization of polyacrylonitrile nanofiber mats obtained by needleless electrospinning using dimethyl sulfoxide as solvent

Lignin-Assisted Stabilization of an Oriented Liquid Crystalline Cellulosic Mesophase, Part B: Toward the Molecular Origin and Mechanism

Potentials of Polyacrylonitrile Substitution by Lignin for Continuous Manufactured Lignin/Polyacrylonitrile-Blend-Based Carbon Fibers

Stabilization of polyacrylonitrile-based fiber with a quasi-traveling microwave applicator