Abstract:We demonstrate a novel transmission color filter design that exploits both dielectric and plasmonic resonances to establish a highly color-selective device, reaching an experimental full-width at half-maximum (fwhm) that is only half that of previously demonstrated cost-effective color filter devices for the same peak transmission and better out-of-band rejection. The measured fwhm is only 25 nm, and the peak transmission reaches up to 53%. The filter uses the interference of Fabry-Pérot resonances and guided-mode resonances in two separated dielectric slabs to achieve this excellent fwhm while relying on propagating surface plasmon polaritons to achieve the excellent out-of-band rejection. A simulation study elucidates the nature of the optical modes in the device and their interference mechanisms and reveals the most important design considerations. Fabrication was done in a CMOS pilot line and is cost-effective, as it requires only two metal patterning steps. Fabrication imperfections are discussed, together with strategies to mitigate them. We show the correct mitigation of these imperfections leads to further performance gain, enabling a full-width at half-maximum down to 20 nm and a peak transmission beyond 60%. We believe this novel filter design is a powerful concept to improve the spectral resolution of color filters for cost-effective multispectral imaging. Beyond multispectral imaging, the design could be adapted for other applications that require on-chip spectral filtering in a thin form factor.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsphotonics.1c01983.Table with dimensions of optimized unit cell designs for different pitches; Transfer matrix method applied to separate SiN sections to isolate Fabry-Pérot resonances; Simulated and measured transmission spectra for the orthogonal polarization (electric field parallel with the grating lines); Simulated transmission spectra for nonzero angle of incidence; Refractive index and extinction coefficient extracted from ellipsometry measurement (PDF)This article has not yet been cited by other publications.

Decorative near-infrared transmission filters featuring high-efficiency and angular-insensitivity employing 1D photonic crystals

Angle-insensitive Decorative NIR Transmission Filter

Design of incident angle-independent color filter based on subwavelength two-dimensional gratings

Highly Efficient Omnidirectional Structural Color Tuning Method Based on Dielectric-Metal-dielectric Structure.

Compact Multilayer Film Structure for Angle Insensitive Color Filtering

Optical Thin-Film Reflection Filters Based on the Theory of Photonic Crystals.

High-color-purity Transmissive Colors with High Angular Tolerance Based on Metal/dielectric Stacks

Design and simulation of omnidirectional reflective color filters based on metal-dielectric-metal structure.

High-Q Filters Based on One-Dimensional Photonic Crystals Using Epsilon-Negative Materials

Inverse Design of Ultranarrow and High-Efficiency Color Filters Based on Tandem Convolutional Neural Networks

Application of phase change material in tunable optical filters and shutters

Flexible High-Color-Purity Structural Color Filters Based on a Higher-Order Optical Resonance Suppression

Plasmon-induced Transparency in a Reconfigurable Composite Valley Photonic Crystal.

Near-infrared Narrow-Band Minus Filter Based on a Mie Magnetic Dipole Resonance

Polarization-insensitive Optical Angular Filtration Enabled by Defective Photonic Crystals

Manipulation of resonance orders and absorbing materials for structural colors in transmission with improved color purity

Highly Selective Color Filters Based on Hybrid Plasmonic–Dielectric Nanostructures

Trans-Reflective Structural Color Filters Assisting Multifunctional-Integrated Semitransparent Photovoltaic Window

Bidirectional Angle-Tolerant Polarization-Tuned Filtering and Wide-Range Refractive Index Sensing Based on Metal Film Coated Nanograting

Nanostructured Metal-Insulator-metal Resonators for High-Resolution Color Filtering and Spectral Imaging

Tunable Near-Infrared Transparent Bands Based on Cascaded Fabry–Perot Cavities Containing Phase Change Materials