Abstract:Introduction Respiration monitoring is important for evaluating human health [1]. The human exhaled gas is always accompanied by high humidity, so humidity sensors are promising for respiration monitoring [2]. Importantly, a fast response to humidity change and good stability under high humidities must be guaranteed for the utilized humidity sensor. In order to achieve fast response and good stability, humidity sensors based on stable polyelectrolytes were prepared via in-situ thiol-ene click polymerization. This method provides a novel way for preparing high quality humidity sensors. Method The polyelectrolytes were prepared by thiol-ene click polymerization (Fig. 1). Mercaptopropyl polyhedral oligomeric silsesquioxane (50.0 mg), 1,4-divinylbenzene (30.0 mg), sodium p-styrene sulfonate hydrate (5.6 mg), and benzoin dimethyl ether (4.0 mg) were dissolved in mixed solvents of methanol (0.75 mL) and THF (0.5 mL). Then, the obtained mixture was drop-cast onto the ceramic plate interdigitated carbon electrodes. The substrates covered with precursor solution were irradiated under UV light (365 nm, 0.12 J/cm2) for 30 min. The cross-linked humidity sensors were then rinsed with the mixed solvents of methanol and THF to remove unreacted monomers and the catalyst. The thickness of the sensing film is ∼30 μm. Results and Conclusions The impedance results of PMDS and PPDS sensors in a batch were tested at different relative humidities (RHs) (Fig. 2a). There is only tiny response for these two sensors in the humidity range of 11-54% RH. At high humidity range, PPDS sensors show an incredibly small variation, while PMDS sensors show an impedance change of nearly 2 orders of magnitude. PMDS sensor’s response/recovery time between 33 and 95% RH is 0.29/0.47 s (Fig. 2b), and that of PPDS sensor is 0.75/0.48 s (Fig. 2c). In addition, the PMDS sensor shows good long-term response/recovery time stability and impedance stability. The PMDS sensor could distinguish the variation of breath rate and depth among a normal breath, a fast breath, a slow breath, a deep breath, a random breath, and a paused breath (Fig. 3). It is worthy to note that almost every cycle behaves inhaled and exhaled platforms. The signal equilibrium value is very important and beneficial to recognize the single inspiration and expiration. The polyelectrolytes were in situ cross-linked on the substrates with interdigitated electrodes successfully by thiol-ene click polymerization. The obtained optimum sensor shows high response and recovery speeds to humidity change and good stability. Different respiration patterns can be distinguished, and the breath rate/depth of detection subjects can also be determined by the sensor., which is meaningful in future diagnostic breath analysis. References Q.Trung, N.-E.Lee, Flexible and Stretchable Physical Sensor Integrated Platforms for Wearable Human-Activity Monitoring and Personal Healthcare. Adv. Mater. 28 (2016) 4338-4372. doi: 10.1002/adma.201504244. Kano, K.Kim, M.Fujii, Fast-Response and Flexible Nanocrystal-Based Humidity Sensor for Monitoring Human Respiration and Water Evaporation on Skin. ACS Sens. 2 (2017) 828−833. doi: 10.1021/acssensors.7b00199. Figure 1

Ultrafast Response Polyelectrolyte Humidity Sensor for Respiration Monitoring.

Design Strategy for Ultrafast-Response Humidity Sensors Based on Gel Polymer Electrolytes and Application for Detecting Respiration

A novel SAW humidity sensor based on electrosprayed polymerized electrolyte film

Sodium Alginate/MXene-Based Flexible Humidity Sensors with High-Humidity Durability and Application Potentials in Breath Monitoring and Non-Contact Human–Machine Interfaces

Stable Polyelectrolyte Humidity Sensors: Preparation and Application

Fast Response Humidity Sensor Based on Hyperbranched Zwitterionic Polymer for Respiratory Monitoring and Non-Contact Human Machine Interface

A fast response resistive thin film humidity sensor based on poly(4-vinylpyridine) and poly(glycidyl methacrylate)

In Situ Preparation of Porous Humidity Sensitive Composite Via a One-Stone-Two-Birds Strategy

Fast-Response Non-Contact Flexible Humidity Sensor Based on Direct-Writing Printing for Respiration Monitoring

An ultrafast-response and flexible humidity sensor for human respiration monitoring and noncontact safety warning

Single-sided and Integrated Polyaniline/ Poly(vinylidene Fluoride) Flexible Membrane with Micro/nanostructures As Breathable, Nontoxic and Fast Response Wearable Humidity Sensor.

Surface Modification of Polysquaraines to Sense Humidity Within a Second for Breath Monitoring

Flexible Humidity Sensor Based on Electrochemically Polymerized Polypyrrole

Fast response, gas-permeable flexible humidity sensor based on PEDOT:PSS-GO for respiration monitoring

Facile Fabrication of Poly (diallyldimethyl Ammonium Chloride)/ti3c2tx/poly (vinylidene Fluoride) 3D Hollow Fiber Membrane Flexible Humidity Sensor and Its Application in the Monitoring of Health-Related Physiological Activity

A fast response resistance-type humidity sensor based on organic silicon containing cross-linked copolymer

Rapid-response, reversible and flexible humidity sensing platform using a hydrophobic and porous substrate

Humidity Sensors Based on 3D Porous Polyelectrolytes Via Breath Figure Method

High Sensitive And Fast Response Humidity Sensor Based On Polymer Composite Nanofibers For Breath Monitoring And Non-Contact Sensing

High-Performance Ultrafast Humidity Sensor Based on Microknot Resonator-Assisted Mach-Zehnder for Monitoring Human Breath.

MXene/TPU Composite Film for Humidity Sensing and Human Respiration Monitoring