Abstract:Abstract Precisely constraining the source parameters of large earthquakes is one of the primary objectives of seismology. However, the quality of the results relies on the quality of synthetic earth response. Although earth structure is laterally heterogeneous, particularly at shallow depth, most earthquake source studies at the global scale rely on the Green's functions calculated with radially symmetric (1D) earth structure. To avoid the impact of inaccurate Green's functions, these conventional source studies use a limited set of seismic phases, such as long period seismic waves, broadband P and S waves in teleseismic distances (30 degrees < ∆ < 90 degrees), and strong ground motion records at close-fault stations. The enriched information embedded in the broadband seismograms recorded by global and regional networks is largely ignored, limiting the spatiotemporal resolution. Here we calculate 3D strain Green's functions at 30 GSN stations for source regions of 10 selected global earthquakes, with frequency up to 67 mill hertz (15 s), using SPECFEM3D_GLOBE and the reciprocity theorem. The 3D SEM mesh model is composed of mantle model S40RTS, crustal model CRUST2.0, and surface topography ETOPO2. We surround each target event with grids in horizontal spacing of 5 km and vertical spacing of 2.0∼3.0 km, allowing us to investigate not only the mainshock but also the background seismicity. In total, the response at over 210,000 source points is calculated in simulation. The number of earthquakes, including different focal mechanisms, centroid depth range, and tectonic background, could further increase without additional computational cost if they were properly selected to avoid overloading individual CPUs. The storage requirement can be reduced by two orders of magnitude if the output strain Green's functions are stored for periods over 15 s. We quantitatively evaluate the quality of these 3D synthetic seismograms, which are frequency and phase dependent, for each source region using nearby aftershocks, before using them to constrain the focal mechanisms and slip distribution. Case studies show that using a 3D earth model significantly improves the waveform similarity, agreement in amplitude and arrival time of seismic phases with the observations. The limitations of current 3D models are still notable, dependent on seismic phases and frequency range. The 3D synthetic seismograms cannot well match the high frequency (>40mHz) S wave and (>20mHz) Rayleigh wave yet. Though the mean time-shifts are close to zero, the standard deviations are notable. Careful calibration using the records of nearby better located earthquakes is still recommended to take full advantage of better waveform similarity due to the use of 3D models. Our results indicate that it is now feasible to systematically study global large earthquakes using full 3D earth response in a global scale.

Source Parameter Scaling Relations for Shallow Crustal Earthquakes: Exploration With the Single Asperity Model

New Empirical Source-Scaling Laws for Crustal Earthquakes Incorporating Fault Dip and Seismogenic-Thickness Effects

Scaling Laws of the Global Parameters of Source Models from NGA Data

Integrated Seismic Source Model of the 2021 M 7.1 Fukushima Earthquake

Asperity Size and Neighboring Segments Can Change the Frictional Response and Fault Slip Behavior: Insights From Laboratory Experiments and Numerical Simulations

Asperities, barriers, characteristic earthquakes and strong motion prediction

Source parameters and scaling relationships of stress drop for shallow crustal seismic events in Western Europe

Source parameters inversion of the global large earthquakes using 3D SEM Green's functions: Strain Green's function calculation and validation

Global seismic energy scaling relationships based on the type of faulting

Patterns of Causative Faults of Normal Earthquakes in the Fluid‐Rich Outer Rise of Northeastern Japan, Constrained With 3D Teleseismic Waveform Modeling

Stress drops and scaled energies of micro-earthquakes at Koyna-Warna, India: Implications for self-similarity scaling

Self-similarity of low-frequency earthquakes

Seismic Versus Aseismic Slip: Probing Mechanical Properties of the Northeast Japan Subduction Zone

Source Modeling of Deep Plate Boundary 2021 Miyagi Earthquake (Mw7.0) Employing Modified Semi-Empirical Technique with Site Effects: A Step Forward Towards Hazard Mitigation

Heterogeneity of Direct Aftershock Productivity of the Mainshock Rupture

Earthquake Nucleation and Slip Behavior Altered by Stochastic Normal Stress Heterogeneity

Nonergodic Ground-Motion Models for Subduction Zone and Crustal Earthquakes in Japan

Steady‐State Effective Normal Stress in Subduction Zones Based on Hydraulic Models and Implications for Shallow Slow Earthquakes

Onset of Aftershocks: Constraints on the Rate‐and‐State Model

Integrated Investigation on Heterogeneous Lower Crust Rheology in Kyushu and Afterslip Behavior Following the 2016 Mw7.1 Kumamoto Earthquake

Progress in modeling the Tohoku-oki megathrust earthquake cycle and associated crustal deformation processes