Abstract:The thread and spline synchronous rolling process can form the external threaded and external splined tooth profiles on different parts of component by only one rolling process. However, it is a coupled rolling process where the thread rolling coupling with the spline rolling, and both phase adjusting requirements of dies before rolling for thread rolling and spline rolling should be satisfied in the synchronous rolling process. Thus, the phase adjustment only by rotating die may be difficult to ensure the thread and spline rolling by different dies well connects respectively. In this paper, requirements of phase difference adjustment for dies before thread rolling and before spline rolling have been studied systematically, and the mathematical expressions of phase difference adjustment have been established, and then the requirements of phase difference under different starts of threaded workpiece and die (or teeth of splined workpiece and die) for two and three rolling dies before thread rolling (or spline rolling) have been investigated. Based on these, the ratio S of phase difference between corresponding threaded sections of rolling dies to that between corresponding splined sections of rolling dies was introduced, and the phase characteristic between dies and the method of phase difference adjustment under different parameters in thread and spline synchronous rolling process were systematically researched. The results indicated that: (1) for thread (or spline) rolling process, if the remainder from dividing the starts nw of thread (or teeth Zw of spline) of workpiece by number N of rolling dies is equal to the remainder from dividing the starts nd of thread (or teeth Zd of spline) of rolling die by N, i.e., nw≡nd(mod N) (or Zw≡Zd(mod N)), then the phases of dies before rolling are the same, else there is a phase difference between dies; (2) for thread and spline synchronous rolling process, if the phase difference of splined section between rolling die j (j = 2,…, N) and rolling die 1 is φsj1=hNθsh=1,…,N$$ {\varphi}_{{\mathrm{s}}_{j1}}=\frac{h}{N}{\theta}_s\left(h=1,\dots, N\right) $$ and ratio of phase difference is Sj1=Nhk+1k=0,1,2,3,…$$ {S}_{j1}=\frac{N}{h}k+1\left(k=0,1,2,3,\dots \right) $$, then the die structures of two dies are the same, i.e., the relative phase between threaded and splined sections for two dies are the same, else the die structures of rolling dies j and 1 are different and the phase difference for threaded sections of rolling dies and the phase difference for splined sections of rolling dies are assured by die structure itself.

Die Structure and Its Trial Manufacture for Thread and Spline Synchronous Rolling Process

Phase characteristic between dies before rolling for thread and spline synchronous rolling process

New method for forming shaft having thread and spline by rolling with round dies

Research Status of High Efficiency Forming Shaft Parts Having Thread and Spline Coaxially by Synchronous Rolling

Implementing approach of rolling process for inner spline sleeve with medium diameter: radial-feed rolling and through-feed rolling

Analysis of Forming Error During Thread and Spline Synchronous Rolling Process Based on Motion Characteristic

A Note on Phase Characteristic among Rollers Before Thread or Spline Rolling

Influence of Processing Parameters on the Thread and Spline Synchronous Rolling Process: an Experimental Study.

Analysis of Motion Between Rolling Die and Workpiece in Thread Rolling Process with Round Dies

General Phase-Difference Model of Round Dies for Inner and External Helical Profile Rolling Processes with Radial-Feed and Through-Feed

Investigation and implementation for forming lead screw by through-feed rolling process with active rotation

Cold-extrusion Die Design of Subsidiary Transmission Shaft

Finite element modeling and analysis for the integration–rolling–extrusion process of spline shaft

Forming characteristic of thread cold rolling process with round dies

Analysis of Thread Rolling Process Using an Analytical Single Tooth Rolling Model Based on the Slip Line Field Theory and Slab Method

An innovative spinning-rolling process and its intelligent FE modelling for big-tapered profiled ring disk

Improvement of Axial Forging Process for Spline Shaft by Die Design

Motion Characteristic Between Die and Workpiece in Spline Rolling Process with Round Dies

The Design and Simulation of Roller for Machining Involute Spline

Numerical and Experimental Analysis of Deformation Behaviors and Microstructure Evolution in the Thread Rolling Process

The Planetary Rolling Process of Forming the Internal Thread