Abstract:This article has been retracted: please see Elsevier Policy on Article Withdrawal (https://www.elsevier.com/about/our-business/policies/article-withdrawal). <This article has been retracted: please see Elsevier Policy on Article Withdrawal (http://www.elsevier.com/locate/withdrawalpolicy). This article has been retracted at the request of the Editor. Figure 5 duplicates figure 8 of the article that had already appeared in Materials Characterization 98 (2014) 147–161, http://dx.doi.org/10.1016/j.matchar.2014.10.026, figure 12 of the paper that had appeared in Applied Physics A 117 (2014) 2251-2264, http://dx.doi.org/10.1007/s00339-014-8655-1, as well as panels from figure 12 of the article that had appeared in the Journal of Alloys and Compounds 616 (2014) 173–183, http://dx.doi.org/10.1016/j.jallcom.2014.07.143. Figure 6 duplicates figure 9 of the article that had already appeared in Materials Characterization 98 (2014) 147–161, http://dx.doi.org/10.1016/j.matchar.2014.10.026 and figure 13 of the article that had appeared in the Journal of Alloys and Compounds 616 (2014) 173–183, http://dx.doi.org/10.1016/j.jallcom.2014.07.143. Figure 7 duplicates figure 10 of the article that had already appeared in Surface & Coatings Technology 258 (2014) 467–484, http://dx.doi.org/10.1016/j.surfcoat.2014.08.052. One of the conditions of submission of a paper for publication is that authors declare explicitly that their work is original and has not appeared in a publication elsewhere. Re-use of any data should be appropriately cited. As such this article represents an abuse of the scientific publishing system. The scientific community takes a very strong view on this matter and apologies are offered to readers of the journal that this was not detected during the submission process. Journal records indicate that confirmation of the submission and publication of the article was sent to the first author's email address, in addition to an email that used the corresponding author's name (guoyitangforwork@163.com). The corresponding author and the first author wish to mention that the co-author Zion T.H. Tse was not involved in the preparation and handling of this article. He was not informed about the publication and he did not grant the use of his name and affiliation in the publication. Prof. S. Petter Lyngstadaas, Dr. Hanna Tiainen and Dr. Sebastian Geissler from University of Oslo are acknowledged for the considerable effort put into collecting the evidence and reporting this case of multiple publication.)> © 2018

Retraction Note To: Ultra-High Strength and Ductile Lamellar-Structured Powder Metallurgy Binary Ti-Ta Alloys

Retraction Note: Effect of Electropulsing Treatment on the Microstructure, Texture, and Mechanical Properties of Cold-Rolled Ti-6Al-4V Alloy

Retraction notice to “Influence of electropulsing treatment on microstructure and mechanical properties of Ti-6Al-4V alloy strip with lamellar microstructure” [Mater. Sci. Eng. A 622 (2015) 1−6](S0921509314013422)(10.1016/j.msea.2014.11.003)

Retraction Notice to “microstructure, Properties and Temperature Evolution of Electro-Pulsing Treated Functionally Graded Ti-6Al-4V Alloy Strip” [journal of Alloys and Compounds 599 (2014) 1–9]

WITHDRAWN: Nanocrystallization kinetics, structure and magnetic properties of FINEMET-type ribbons with Cu substitution by Ag

RETRACTED: Microstructure and Tribological Characterizations of Ni-based Self-Lubricating Coating

Retraction notice to: “Effect of electropulsing treatment on microstructure and mechanical properties of cold-rolled pure titanium strips” (Journal of Materials Processing Tech. (2015) 222 (27–32), (S0924013615000850), (10.1016/j.jmatprotec.2015.02.035))

RETRACTION: In Situ Observation of Phase Transformations of Pearlite Heat-Resistant Steel during Solidification (Retraction of July, art no 2300172, 2023)

RETRACTION: Enhanced tensile strength and thermal conductivity in copper diamond composites with B<sub>4</sub>C coating (Vol 12, 10727, 2022) (Retraction of Vol 12, art no 10727, 2022)

RETRACTED: Vorotilo et al. Manufacturing of Conductive, Wear-Resistant Nanoreinforced Cu-Ti Alloys Using Partially Oxidized Electrolytic Copper Powder. Nanomaterials 2020, 10, 1261

RETRACTED: Xu et al. Cr–Diamond/Cu Composites with High Thermal Conductivity Fabricated by Vacuum Hot Pressing. Materials 2024, 17, 3711

RETRACTED—Formation and Properties of Zr-based Bulk Quasicrystalline Alloys with High Strength and Good Ductility

RETRACTED: Effect of Electropulsing Treatment and Ultrasonic Striking Treatment on the Mechanical Properties and Microstructure of Biomedical Ti-6Al-4v Alloy

Notice of Retraction: Forming Analysis of Aluminium Alloy Workpiece

Retraction: Zhu et al. The Effect of Vacuum Annealing Temperature on the Properties of AlCrTiSiN Coating Prepared by Arc Ion Plating. Coatings 2022, 12, 316

Retraction notice to “ Effects of high-energy electro-pulsing treatment on microstructure, mechanical properties and corrosion behavior of Ti–6Al–4V alloy” [MSEC Volume 49, Year 2015, Pages 851-860](S0928493115000910)(10.1016/j.msec.2015.01.081)

RETRACTED: Mechanical properties and phase transition of biomedical titanium alloy strips with initial quasi-single phase state under high-energy electropulses

RETRACTED: Shi et al. Effect of Final Rolling Temperature on Microstructures and Mechanical Properties of AZ31 Alloy Sheets Prepared by Equal Channel Angular Rolling and Continuous Bending. Materials 2020, 13, 3346

WITHDRAWN: High Cycle Fatigue Behavior of Extruded Mg–Zn–Y–Zr Alloys Containing Varying Contents of Yttrium

Retraction Note: Enhanced tensile strength and thermal conductivity in copper diamond composites with B4C coating

Retracted: Investigation of Tribological Behaviour on DLC Coatings for AA5051 using DC Sputtering