Abstract:Metal-organic frameworks (MOFs) have attracted a great deal of interest from both academia and industry due to their extensive potential applications. The tunable physical properties through the manipulation of composition have led to increasing attention to the exploration of the MOF applications. However, the tunability of physical property of MOF with external mechanical load, which usually steams from actual fabrication and application processes, has been rarely investigated. Here, ab initio (first-principles) density functional theory calculations are performed to investigate the mechanical, electrical properties and strain engineering of a typical metal-organic framework, MOF-5. Preliminary calculations by using different pseudopotentials and cut-off energies are performed to verify the adopted critical parameters in subsequent simulations. Both the structural stability of MOF-5 and the effect of applied strain are investigated from an energetic point of view. With the increase of applied strain, the cohesive energy of MOF-5 decreases, inducing the reduction of structural stability. In addition, the variation of cohesive energy of MOF-5 shows an asymmetry under expansive and compressive conditions. By applying strain along different directions, the mechanical properties of MOF-5 are systematically investigated, and mechanical constants including Young's modulus, Poisson ratio and elastic constants are obtained. In addition, by analyzing the band gap of MOF-5, the intrinsic electrical property of MOF-5 is clarified. The band gap of MOF-5 is 3.49 eV, indicating that MOF-5 is a wide bandgap semiconductor, which is represented by the combination effect of both [Zn4O](6+) metal clusters and organic linkers. Analysis on the strain engineering of electrical properties of MOF-5 reveals that the applied strain induces the decrease of band gap of MOF-5, and thus leading to the increase of conductivity. This transition is induced by the decrease of conduction energy-level. Further studies on the variations of PDOS and covalent bond show that the strain engineering of electrical property of MOF-5 intrinsically originates from the variation of covalent bond in the organic linker. The applied strain apparently weakens the covalent bond, and thus inducing the relaxation and redistribution of electrons, which increases the activities of electrons, and finally leads to the overall increase of conductivity of MOF-5. This theoretical study quantitatively clarifies the tunability of electronic band gap of MOF-5 with external strain, and provides a theoretical guidance in the design optimization and property evaluation of gas sensors based on MOF-5.

Common but differentiated flexible MIL-53(Al): role of metal sources in synthetic protocol for tuning the adsorption characteristics

(Invited, Digital Presentation) Atomic Layer Deposited Templates for Constructing Functional Metal-Organic Framework Thin Films

Tuning strategies of MIL metal organic frameworks for adsorptive removal of formaldehyde in air

Regulation of hydrophobicity and water adsorption of MIL-101(Cr) through post-synthetic modification

A Comparative Study of Rigid and Flexible MOFs for the Adsorption of Pharmaceuticals: Kinetics, Isotherms and Mechanisms

One-Pot Synthesis of Two-Linker Mixed Al-Based Metal–Organic Frameworks for Modulated Water Vapor Adsorption

Dialing in Catalytic Sites on Metal Organic Framework Nodes: MIL-53(Al) and MIL-68(Al) Probed with Methanol Dehydration Catalysis

Synthesis of Hierarchical-Porous Fluorinated Metal-Organic Frameworks with Superior Toluene Adsorption Properties

First-Principle Studies of Mechanical, Electronic Properties and Strain Engineering of Metal-Organic Framework

Synthesis Methods and Influencing Factors of Metal Organic Framework Material MIL-53

Size- and Morphology-Controlled Nh2-Mil-53(Al) Prepared in Dmf-Water Mixed Solvents

Simultaneous adsorption of anionic and cationic species on UiO-66 and MIL-125 MOFs: Mechanisms & selectivity

Tuning Hydrophilicity of Aluminum MOFs by a Mixed‐Linker Strategy for Enhanced Performance in Water Adsorption‐Driven Heat Allocation Application

Alkenyl/Thiol-Derived Metal-Organic Frameworks (mofs) by Means of Postsynthetic Modification for Effective Mercury Adsorption

Experimental investigations into the irregular synthesis of iron(iii) terephthalate metal-organic frameworks MOF-235 and MIL-101

Small Molecules, Big Effects: Tuning Adsorption and Catalytic Properties of Metal–Organic Frameworks

Tailoring Lewis Acid Properties of Metal–Organic Framework Nodes via Anion Post-Replacement for Gas Adsorption and Separation

Structure Stability of Metal-Organic Framework MIL-53 (al) in Aqueous Solutions

Solvent Impact on the Properties of Benchmark Metal-Organic Frameworks: Acetonitrile-Based Synthesis of CAU-10, Ce-UiO-66, and Al-MIL-53

Introducing High Density of Very Active Sites and Stepwise Postmodification for Tailoring the Porosity of Highly Demanding Cr 3+ -Based Metal–Organic Frameworks

Tuning the Atrazine Binding Sites in an Indium-Based Flexible Metal-Organic Framework