Novel Self-Strengthening Hybrid Dentin Adhesive Via a Facile Visible-Light Irradiation Triple Polymerization
Ye Qiang,Song Linyong,Ge Xueping,Misra Anil,Spencer Paulette
DOI: https://doi.org/10.3389/conf.fbioe.2016.01.01192
IF: 5.7
2016-01-01
Frontiers in Bioengineering and Biotechnology
Abstract:Event Abstract Back to Event Novel self-strengthening hybrid dentin adhesive via a facile visible-light irradiation triple polymerization Qiang Ye1, Linyong Song1, Xueping Ge1, Anil Misra1, 2 and Paulette Spencer1, 3 1 University of Kansas, Bioengineering Research Center, United States 2 University of Kansas, Department of Civil Engineering, United States 3 University of Kansas, Department of Mechanical Engineering, United States Introduction: In vivo biodegradation of the bond between the composite and tooth, i.e. the composite restoration’s adhesive bond layer, is considered a major contributor to premature failure of composite restorations[1]. The structure of methacrylate-based dentin adhesives suggests a general mechanism for their chemical and enzymatic degradation in oral fluids. In our previous study[2], the crosslink density of dentin adhesives can be improved with the addition of epoxide monomers. The objective of this work was to further develop a self-strengthening methacrylate-based dentin adhesive system by introducing an epoxy cyclohexyl trimethoxysilane (TS) containing both epoxy and methoxysilyl functional groups and cured by visible-light photopolymerization. Materials and Methods: Neat methacrylate monomer mixture (Scheme 1) of HEMA/BisGMA at 45/55 wt% was used as the control (C0). Experimental formulation with HEMA/BisGMA/TS (22.5/27.5/50, wt%) was used to investigate the free radical polymerization of methacrylate, ring-opening cationic polymerization of epoxy, and photoacid-induced sol-gel reaction. The polymerization behavior was monitored in-situ using real-time Fourier transform infrared spectroscopy (FTIR). The properties of copolymers at TS concentration from 5 to 35 wt% were determined using dynamic mechanical analysis (DMA). The leachables from polymer discs were determined by HPLC using a reverse phase C18 column and UV/diode array detectors. Results and Discussion: In this triple polymIn this triple polymerization system, free radical polymerization rate was the highest and the hydrolysis-condensation reaction was the slowest. In acidic environments, the fast hydrolysis reaction and the limited condensation gave rise to the self-strengthening process, which significantly improved the mechanical properties. When the TS concentration was 10-20 wt%, the copolymers became more homogeneous and the storage modulus at 70 0C reached maximum. The cumulative amounts of leached monomers were reduced significantly (Figure 1). Conclusion: With the introduction of both epoxy and trimethoxysilyl functional groups, a self-strengthening hybrid system has been developed for application as a dentin adhesive. During visible-light irradiation, a triple polymerization mechanism was involved (Figure 2). Supported by grant NIH/NIDCR R01 DE022054. Scheme 1. Chemical structures of monomers used in the formulations. Figure 1. Cumulative release of HEMA from the dentin adhesive copolymers as a function of incubation time in ethanol at 23±2 0C Figure 2. Proposed polymethacrylate-based matrix network structure and the autonomic self-strengthening process with different TS concentrations. (A1 and A2) Polymethacrylate-based network formed by free radical polymerization, cationic ring-opening polymerization, and limited photoacid-induced sol-gel reaction in dry conditions after 40 s irradiation; (B1 and B2) photoacid-induced ring-opening polymerization and sol-gel reaction after 24 h; (C1 and C2) self-strengthening process via sol-gel reaction and ring-opening polymerization in wet environment. Supported by grant R01DE022054 (PS, JSL), from the National Institute of Dental and Craniofacial Research, National Institutes of Health, Bethesda, MD 20892.References:[1] Spencer P et al. Annals of Biomedical Engineering, 38(6):1989-2003, 2010.[2] Song, L.Y., et al., Journal of Biomedical Materials Research Part B-Applied Biomaterials, 2015, published online, doi: 10.1002/jbm.b.33435 Keywords: microstructure, Functionalization, Smart material, Polymeric material Conference: 10th World Biomaterials Congress, Montréal, Canada, 17 May - 22 May, 2016. Presentation Type: Poster Topic: Combinatorial approaches to biomaterial design Citation: Ye Q, Song L, Ge X, Misra A and Spencer P (2016). Novel self-strengthening hybrid dentin adhesive via a facile visible-light irradiation triple polymerization. Front. Bioeng. Biotechnol. Conference Abstract: 10th World Biomaterials Congress. doi: 10.3389/conf.FBIOE.2016.01.01192 Copyright: The abstracts in this collection have not been subject to any Frontiers peer review or checks, and are not endorsed by Frontiers. They are made available through the Frontiers publishing platform as a service to conference organizers and presenters. The copyright in the individual abstracts is owned by the author of each abstract or his/her employer unless otherwise stated. Each abstract, as well as the collection of abstracts, are published under a Creative Commons CC-BY 4.0 (attribution) licence (https://creativecommons.org/licenses/by/4.0/) and may thus be reproduced, translated, adapted and be the subject of derivative works provided the authors and Frontiers are attributed. For Frontiers’ terms and conditions please see https://www.frontiersin.org/legal/terms-and-conditions. Received: 27 Mar 2016; Published Online: 30 Mar 2016. Login Required This action requires you to be registered with Frontiers and logged in. To register or login click here. Abstract Info Abstract The Authors in Frontiers Qiang Ye Linyong Song Xueping Ge Anil Misra Paulette Spencer Google Qiang Ye Linyong Song Xueping Ge Anil Misra Paulette Spencer Google Scholar Qiang Ye Linyong Song Xueping Ge Anil Misra Paulette Spencer PubMed Qiang Ye Linyong Song Xueping Ge Anil Misra Paulette Spencer Related Article in Frontiers Google Scholar PubMed Abstract Close Back to top Javascript is disabled. Please enable Javascript in your browser settings in order to see all the content on this page.