Abstract:Background context: Facet joints have been discussed as influential factors in the development of lumbar degeneration, which includes disc herniation and degenerative lumbar spondylolisthesis. Facet orientation (FO) and facet tropism (FT) are two important structural parameters of the lumbar facet joints. Many previous studies have focused on single parameter analysis of the lumbar spine. Owing to the correlation between independent variables, single-factor analysis cannot reflect the interaction between variables; however, there has been no corresponding biomechanical method developed to address this problem. Purpose: To investigate the complex biomechanical influences on the lumbar spine when vertebral FO and FT are varied using finite element analysis (FEA) and contour maps visualization, and analyze the biomechanical role of facet joint structural parameters in the process of lumbar degenerative diseases. Study design: A biomechanical modelling, analysis, and verification study was performed. Methods: A three-dimensional non-linear FEA model of 3 denucleated intervertebral discs (L2-3, L3-4, L4-5) with adjacent vertebral bodies (L2-L5) was created. Previously performed in vitro experiments provided experimental data for the range of motion in each load direction that was used for calibration. For 12 lumbar models, different facet joint angles relative to the sagittal plane at both L3-4 facet joints were simulated for 35°≤FO≤50° and 0°≤FT≤15°. By modifying different values of FO and FT, FEA simulation of different lumbar spine models was performed. Contour maps were used to visualize the FO- and FT-relevant data. Results: Under flexion, extension, and torsion moments, facet joint contact force and intradiscal stress increased with increasing FT. In the condition where FT remained 0° and increasing FO values, facet joint contact force and intradiscal stress remained low with no apparent increasing or decreasing trend when the model was under flexion, extension, and torsion moments. In the condition where FO and the FT values were varied at the same time, the highest force and stress regions in the contour maps were observed when all three types of moments were applied. Stress distributions of the L3-4 disc with different FT and FO values showed disc stress increased significantly with increases of FT and was concentrated on the ipsilateral region of the facet joint with the more sagittal orientation. Conclusions: The combination of FO and FT has an important impact on the corresponding disc and facet joints, but FT played a more significant role. Moreover, disc stress was concentrated on the ipsilateral region of facet joint with greater sagittal orientation when FT existed. FT with high sagittal orientation may increase risk of recurrent LDH due to increase ipsilateral disc pressure. Clinical significance: These biomechanical findings may help clinicians to understand the prognosis of some lumbar degenerative conditions.

A Validated Finite Element Analysis of Facet Joint Stress in Degenerative Lumbar Scoliosis.

Influence of the Morphology of Lumbar Motion Segment on Isthmic Stress and Facet Contact Force: A Finite Element Analysisangzh

Contribution of Sagittal Orientation of Facet Joints and Disc Degeneration to Degenerative Spondylolisthesis in Lumbar Spine: A Finite Element Research

The Effects of Adult Degenerative Lumbar Scoliosis on the Facet Joint Contact Forces: A Finite Element Study

Finite element analysis of the lumbar spine in adolescent idiopathic scoliosis subjected to different loads

Research on Spinal Lumbar Sacral Degeneration Finite Element Model

Facet Joint Orientation and Sagittal Spinopelvic Alignment in Patients with Degenerative Lumbar Scoliosis

Motion of Lumbar Endplate in Degenerative Lumbar Scoliosis Patients with Different Cobb Angle in Vivo: Reflecting the Biomechanics of the Lumbar Disc

Finite Element Based-Analysis for Pre and Post Lumbar Fusion of Adult Degenerative Scoliosis Patients

Stress Analysis of the Lower Lumbar Spine Three-Joint Complex According to Different Pelvic Incidences

Sagittal Plane Analysis of the Spine and Pelvis in Degenerative Lumbar Scoliosis

Analyzing isolated degeneration of lumbar facet joints: implications for degenerative instability and lumbar biomechanics using finite element analysis

Analysis of the facet joint morphology for degenerative lumbar spondylolisthesis

Biomechanical Study of Symmetric Bending and Lifting Behavior in Weightlifter with Lumbar L4-L5 Disc Herniation and Physiological Straightening Using Finite Element Simulation

Development of a spinopelvic complex finite element model for quantitative analysis of the biomechanical response of patients with degenerative spondylolisthesis

Flexibility of the coronal lumbosacral region of congenital scoliosis: a three-dimensional finite element analysis

Etiological Relationship Between the Facet Joint Angle and Degenerative Lumbar Spondylolisthesis

Lumbar spine finite element model for healthy subjects: development and validation

Finite element analysis on scoliosis lumbosacral vertebral structure and its deformation trend

The biomechanical influence of facet joint parameters on corresponding segment in the lumbar spine: a new visualization method

[Correlation Study Between Sagittal Lumbar Facet Joint and Degenerative Lumbar Spondylolisthesis].