Abstract:OBJECTIVE:To investigate influence of setting time on bond strength of different bioactive pulp capping materials with self-etch or etch-and-rinse adhesive.METHODS:Sixty specimens were prepared for each of the three tested capping materials, namely mineral trioxide aggregate (MTA), iRoot BP Plus (BP) and iRoot FS (FS). Specimens of each material were divided into three groups and bonded at three setting time points of the materials respectively: initial setting time (4 h for MTA, 2 h for BP and 20 min for FS), 24 h after application and 7 d after application. The specimen surfaces of each group were treated with self-etch mode or etch-and-rinse mode of one universal adhesive (Single Bond Universal, SBU) (n=10). The bonding area was restricted to a round area with 3 mm diameter, on which composite cylinders were build up with flowable composite and light cured completely. The shear bond strength was tested immediately with a shear strength tester and fracture mode was observed under stereo microscope and recorded. The mean shear bond strength for each group was analyzed with SPSS 19.0 software ANOVA method. The surface morphology of each material was observed after setting and acid treatment under scanning electron microscope.RESULTS:There was no significant difference among the three tested materials at either initial setting point or 7 d after application (P<0.05). The bond strength of MTA was significantly higher than those of BP and FS 24 h after application in both bonding modes (P<0.05). For all the three tested materials, shear bond strength was significantly higher for complete setting group than for initial setting group of the same material (P<0.05). Under scanning electron microscope, the characteristic crystal patterns could be observed on the three bioactive materials surfaces after complete setting, the size of which was bigger for MTA than for BP and FS. These features were lost to some extent after self-etch primer application or phosphoric acid etching.CONCLUSION:Based on the present results, adequate bond strength can be obtained for FS at initial setting time, which is comparable with BP and MTA. This implies that clinically composite restoration can be placed over bioactive direct capping materials after shortened initial setting process in one visit.

[Comparative Study of Three Bonding Methods in Attaching Removable Thermoplastic Appliances].

Influence of Casein Phosphopeptide-Amorphous Calcium Phosphate Application, Smear Layer Removal, and Storage Time on Resin-Dentin Bonding

Comparative study of three composite materials in bonding attachments for clear aligners

The clinical evaluation for three types of orthodontic bracket bonding cement applied to patients with Angle classⅡmalocclusion and the care

Comparison of the bond strength of five different composites used in the production of clear aligner attachments

[Effects of Three Self-Etch Adhesives and Mild Salivary Contamination on the Bonding Durability of Deciduous Teeth].

A comparison of bond strength between direct- and indirect-bonding methods

[Comparison of flow conditions of adhesives and retention force of restorations among four cement-retained methods of implant-supported fixed prostheses]

[Influence of Setting Time on Bond Strength of Different Bioactive Pulp Capping Materials with Dental Adhesive].

Comparison of a recently developed nanofiller self-etching primer adhesive with other self-etching primers and conventional acid etching

Comparative Evaluation of Shear Bond Strength, Enamel Microfracture, and Adhesive Remnant Index of APC Flash-Free System Versus Traditional Bonding: An In-Vitro Study

[Effects of Application Methods of Self-Etching Adhesives on Resin-Dentin Bonding].

[The Durability of Three Self-Etch Adhesives Bonded to Dentin].

Adhesive Interfacial Characteristics and the Related Bonding Performance of Four Self-Etching Adhesives with Different Functional Monomers Applied to Dentin.

Experimental study of bonding strength between resin composite direct core build-up materials and dentin in vitro

An In-Vitro Comparison of Shear Bond Strength and Adhesive Remnant Score Between Two Color Change Adhesives in Orthodontic Bonding With Reduced Curing Time Using Different High-Intensity Light Emitting Diode Units

Comparison of Enamel Discoloration Associated with Bonding with Three Different Orthodontic Adhesives and Cleaning-Up with Four Different Procedures.

Experimental Study on Bond Strength of Machinable Composite Resin and Dentin with Three Kinds of Resin Cements

Influence of different but compatible all-ceramic materials and bonding systems on dentin bonding properties

Cross-compatibility of methacrylate-based resin composites and etch-and-rinse one-bottle adhesives

[Research progress in the performance of clear aligner attachment materials]